Network Working Group M. Ahmed
Request for Comments: 1695 K. Tesink
Category: Standards Track Editors
Bell Communications Research
August 1994
Definitions of Managed Objects
for ATM Management Version 8.0
using SMIv2
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Table of Contents
1. Introduction ............................................. 2
2. The SNMPv2 Network Management Framework .................. 2
3. Object Definitions ....................................... 2
4. ATM Terminology .......................................... 3
4.1 VCL/VPL and VCC/VPC ..................................... 3
4.2 PVC and SVC ............................................. 5
4.3 Traffic Management Parameters ........................... 5
4.3.1 Traffic Policing and Traffic Shaping Parameters ...... 5
4.3.2 Cell Loss Priority .................................... 6
4.3.3 QoS Class ............................................. 6
5. Overview ................................................. 7
5.1 Background .............................................. 7
5.2 Structure of the MIB .................................... 7
5.3 ATM Interface Configuration Group ....................... 7
5.4 ATM Interface DS3 PLCP and TC Layer Groups .............. 8
5.5 ATM Virtual Link and Cross-Connect Groups ............... 8
6. Application of MIB II to ATM ............................. 8
6.1 The System Group ........................................ 8
6.2 The Interface Group ..................................... 8
6.2.1 Support of the ATM Cell Layer by ifTable .............. 9
7. Support of the AAL3/4 Based Interfaces ................... 10
8. Support of the AAL5 Managed Objects ...................... 10
8.1 Managing AAL5 in a Switch ............................... 11
8.2 Managing AAL5 in a Host ................................. 12
8.3 Support of AAL5 by ifTable .............................. 13
8.4 Support of Proprietary Virtual Interface by ifT-able .. 14
8.5 AAL5 Connection Performance Statistics Group ............ 15
Ahmed & Tesink [Page 1]
RFC 1695 ATM Management Objects August 1994
9. ILMI MIB and the ATM Managed Objects ..................... 15
10. Definitions ............................................. 18
11. Acknowledgments ......................................... 72
12. References .............................................. 72
13. Security Considerations ................................. 73
14. Authors' Addresses ...................................... 73
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes objects used for managing ATM-based
interfaces, devices, networks and services.
This memo specifies a MIB module in a manner that is both compliant
to the SNMPv2 SMI, and semantically identical to the peer SNMPv1
definitions.
2. The SNMPv2 Network Management Framework
The SNMPv2 Network Management Framework consists of four major
components. They are:
0 RFC 1442 [1] which defines the SMI, the mechanisms used
for describing and naming objects for the purpose of
management.
0 STD 17, RFC 1213 [2] defines MIB-II, the core set of
managed objects for the Internet suite of protocols.
0 RFC 1445 [3] which defines the administrative and other
architectural aspects of the framework.
0 RFC 1448 [4] which defines the protocol used for network
access to managed objects.
The Framework permits new objects to be defined for the purpose of
experimentation and evaluation.
3. Object Definitions
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the subset of Abstract Syntax Notation One (ASN.1)
defined in the SMI. In particular, each object type is named by an
OBJECT IDENTIFIER, an administratively assigned name. The object
type together with an object instance serves to uniquely identify a
specific instantiation of the object. For human convenience, we
Ahmed & Tesink [Page 2]
RFC 1695 ATM Management Objects August 1994
often use a textual string, termed the descriptor, to also refer to
the object type.
4. ATM Terminology
Some basic ATM terminologies are described in this section to
facilitate defining the ATM managed objects.
4.1. VCL/VPL and VCC/VPC
There are two distinct types of ATM virtual connections: Virtual
Channel Connections (VCCs) and Virtual Path Connection (VPCs). As
shown in Figures 1 and 2, ATM virtual connections consist of
concatenated series of virtual links which forms a path between two
end points, with each concatenation occurring at an ATM switch.
Virtual links of VCCs are called Virtual Channel Links (VCLs).
Virtual links of VPCs are called Virtual Path Links (VPLs). The VCI
and VPI fields in the ATM cell header associate each cell of a VCC
with a particular VCL over a given physical link. The VPI field in
the ATM cell header associates each cell of a VPC with a particular
VPL over a given physical link. Switches route cells between VCLs
(or VPLs) via a cross-connect function according to the cells'
VCI/VPI (or VPI) values.
<-----------------------VCC-------------------------->
------------ -----------
|ATM | |ATM |
|X-Connect | |X-Connect |
VCL1 |Point | VCL2 |Point | VCL3
O---------|----X-----|-------|-----|----X-----|-------O
| | | |
------------ ------------
ATM Switch ATM Switch
Figure 1: Virtual Channel Links and
Virtual Channel Connection
Ahmed & Tesink [Page 3]
RFC 1695 ATM Management Objects August 1994
<-----------------------VPC-------------------------->
------------ -----------
|ATM | |ATM |
|X-Connect | |X-Connect |
VPL1 |Point | VPL2 |Point | VPL3
O---------|----X-----|-------|-----|----X-----|-------O
| | | |
------------ ------------
ATM Switch ATM Switch
Figure 2: Virtual Path Links and
Virtual Path Connection
A single ATM end-system or switch does not support the whole end-to-
end span of a VCC (or VPC). Rather, multiple ATM end- systems and/or
switches each support one piece of the VCC (or VPC). That is, each
ATM end-system at one end of the VCC/VPC supports its end of the
VCC/VPC plus the VCLs or VPLs on its external interfaces, and each
switch through which the VCC/VPC passes, supports the multiple
VCLs/VPLs on that switch's external interfaces and the cross-
connection of those VCLs/VPLs through that switch. Thus, the end-
to-end management of a VCC or VPC is achieved only by appropriate
management of its individual pieces in combination.
Note that for management purposes, an ATM network may be viewed as a
large distributed switch by hiding all the network's internal
connectivity as being internal to the distributed switch (as shown in
Figure 2a). This model may for example be used for Customer Network
Management (CNM) purposes.
Ahmed & Tesink [Page 4]
RFC 1695 ATM Management Objects August 1994
<---------------------VCC--------------------------->
--------------------------------------
| |
| ---------- ---------- |
| | ATM | | ATM | |
VCL1 | | Switch | | Switch | | VCL3
O-------|-|--------|------/-------|--------|-|------O
| | | | | |
| ---------- ---------- |
| |
| ATM Network |
--------------------------------------
Figure 2a: ATM Network modeled as a large distributed
switch
A VCC has a set of traffic characteristics (i.e., bandwidth
parameters, QoS Class parameters, etc.). VCLs inherit their traffic
characteristics from the VCC of which they are a part. VCCs are bi-
directional by definition. However, the traffic parameters in the
two directions of a connection can be symmetric or asymmetric, i.e.,
the two directions can have the same or different traffic flows. A
uni-directional traffic flow across a VCC is achieved by assigning a
zero bandwidth in one direction. Note that in addition to the
bandwidth required by the user traffic flow, bandwidth is also
required for OAM cell flows, even for the zero-bandwidth direction of
a uni-directional connection. These same principles apply to VPCs.
4.2. PVC and SVC
A Permanent Virtual Connection (PVC) is a provisioned VCC or VPC. A
Switched Virtual Connection (SVC) is a switched VCC or VPC that is
set up in real-time via call set-up signaling procedures. A PVC (or
an SVC) can be a point-to-point, point-to-multipoint, or multipoint-
to-multipoint VCC or VPC.
4.3. Traffic Management Parameters
4.3.1. Traffic Policing and Traffic Shaping Parameters
In order to allocate resources fairly among different users, some
networks police traffic at resource access points. The traffic
enforcement or policing taken at a UNI is called Usage Parameter
Control (UPC) and is activated on an incoming VCL or VPL as shown in
Figure 3. The use of the traffic enforcer at the ingress of the
connection is to make sure that the user traffic does not exceed the
Ahmed & Tesink [Page 5]
RFC 1695 ATM Management Objects August 1994
negotiated traffic parameters such as the peak cell rate associated
with a specific traffic descriptor type.
---------- ----------
UNI | ATM | NNI | ATM | UNI
| | switch | | | switch | |
O<---|---->X(UPC) |<----|------>| (UPC)X<-----|--->O
| VCL | | | VCL | | VCL |
---------- ----------
Figure 3: An Example of a UPC
In addition, traffic shaping may be performed on an outgoing VPL or
VCL at a given ATM interface. The function of the ATM traffic shaper
either at the source or an egress point of the connection is to
smooth the outgoing cell traffic inter-arrival time. If policing or
shaping is not performed then the policing or shaping algorithm is
not activated. ATM Forum has specified seven traffic descriptor
types including one for the best effort traffic [9].
4.3.2. Cell Loss Priority
To prioritize traffic during resource congestion, ATM cells are
assigned one of the two types of Cell Loss Priority (CLP), CLP=0 and
CLP=1. ATM cells with CLP=0 have a higher priority in regard to cell
loss than ATM cells with CLP=1. Therefore, during resource
congestions, CLP=1 cells are dropped before any CLP=0 cell is
dropped.
4.3.3. QoS Class
A VCC or VPC is associated with one of a number of Quality of Service
(QoS) classes. The following service classes have been specified:
Service Class A: Constant bit rate video and Circuit
emulation
Service Class B: Variable bit rate video/audio
Service Class C: Connection-oriented data
Service Class D: Connectionless data
Four QoS classes numbered 1, 2, 3, and 4 have been specified with the
aim of supporting service classes A, B, C, and D respectively. The
VCLs (or VPLs) concatenated to form a VCC (or VPC) will all have the
same QoS class as that of the VCC (or VPC). The Cell Loss Ratio
(CLR), Cell Delay Variation (CDV), and end-to-end Cell Delay (CD)
parameters are defined as part of QoS Class definition. In addition,
Ahmed & Tesink [Page 6]
RFC 1695 ATM Management Objects August 1994
an unspecified QoS Class numbered 0 is specified for best effort
traffic.
5. Overview
ATM management objects are used to manage ATM interfaces, ATM virtual
links, ATM cross-connects, AAL5 entities and AAL5 connections
supported by ATM hosts, ATM switches and ATM networks. This section
provides an overview and background of how to use this MIB and other
potential MIBs for this purpose.
The purpose of this memo is primarily to manage ATM PVCs. ATM SVCs
are also represented by the management information in this MIB.
However, full management of SVCs may require additional capabilities
which are beyond the scope of this memo.
5.1. Background
In addition to the MIB module defined in this memo, other MIB modules
are necessary to manage ATM interfaces, links and cross-connects.
Examples include MIB II for general system and interface management
(RFC 1213 and RFC 1573), the DS3 or SONET MIBs for management of
physical interfaces, and, as appropriate, MIB modules for
applications that make use of ATM, such as SMDS. These MIB modules
are outside the scope of this specification.
The current specification of this ATM MIB is based on SNMPv2.
5.2. Structure of the MIB
The managed ATM objects are arranged into the following groups:
(1) ATM interface configuration group
(2) ATM interface DS3 PLCP group
(3) ATM interface TC Sublayer group
(4) ATM interface virtual link (VPL/VCL) configuration
groups
(5) ATM VP/VC cross-connect groups
(6) AAL5 connection performance statistics group
Note that, managed objects for activation/deactivation of OAM cell
flows and ATM traps notifying virtual connection or virtual link
failures are outside the scope of this memo.
5.3. ATM Interface Configuration Group
This group contains information on ATM cell layer configuration of
local ATM interfaces on an ATM device in addition to the information
Ahmed & Tesink [Page 7]
RFC 1695 ATM Management Objects August 1994
on such interfaces contained in the ifTable.
5.4. ATM Interface DS3 PLCP and TC Layer Groups
These groups provide performance statistics of the DS3 PLCP and TC
sublayer of local ATM interfaces on a managed ATM device. DS3 PLCP
and TC sublayer are currently used to carry ATM cells respectively
over DS3 and SONET transmission paths.
5.5. ATM Virtual Link and Cross-Connect Groups
ATM virtual link and cross-connect groups model bi-directional ATM
virtual links and ATM cross-connects. The ATM VP/VC link groups are
implemented in an ATM host, ATM switch and ATM network. The ATM
switch and ATM network also implement the ATM VP/VC cross-connect
groups. Both link and cross-connect groups are implemented in a
carrier's network for Customer Network Management (CNM) purposes.
The ATM virtual link groups are used to create, delete or modify ATM
virtual links in an ATM host, ATM switch and ATM network. ATM
virtual link groups along with the cross-connect groups are used to
create, delete or modify ATM cross-connects in an ATM switch or ATM
network (e.g., for CNM purposes).
6. Application of MIB II to ATM
6.1. The System Group
For the purposes of the sysServices object in the System Group of MIB
II [2], ATM is a data link layer protocol. Thus, for ATM switches
and ATM networks, sysServices will have the value "2".
6.2. The Interface Group
The Interfaces Group of MIB II defines generic managed objects for
managing interfaces. This memo contains the media-specific
extensions to the Interfaces Group for managing ATM interfaces.
This memo assumes the interpretation of the Interfaces Group to be in
accordance with [5] which states that the interfaces table (ifTable)
contains information on the managed resource's interfaces and that
each sub-layer below the internetwork layer of a network interface is
considered an interface. Thus, the ATM cell layer interface is
represented as an entry in the ifTable. This entry is concerned with
the ATM cell layer as a whole, and not with individual virtual
connections which are managed via the ATM-specific managed objects
specified in this memo. The inter-relation of entries in the ifTable
is defined by Interfaces Stack Group defined in [5].
Ahmed & Tesink [Page 8]
RFC 1695 ATM Management Objects August 1994
6.2.1. Support of the ATM Cell Layer by ifTable
Some specific interpretations of ifTable for the ATM cell layer
follow.
Object Use for the generic ATM layer
====== =============================
ifIndex Each ATM port is represented by an ifEntry.
ifDescr Description of the ATM interface.
ifType The value that is allocated for ATM is 37.
ifSpeed The total bandwidth in bits per second
for use by the ATM layer.
ifPhysAddress The interface's address at the ATM protocol
sublayer; the ATM address which would be used
as the value of the Called Party Address
Information Element (IE) of a signalling
message for a connection which either:
- would terminate at this interface, or
- for which the Called Party Address IE
would need to be replaced by the Called
Party SubAddress IE before the message
was forwarded to any other interface.
For an interface on which signalling is
not supported, then the interface does not
necessarily have an address, but if it
does, then ifPhysAddress is the address which
would be used as above in the event that
signalling were supported. If the interface
has multiple such addresses, then ifPhysAddress
is its primary address. If the interface has
no addresses, then ifPhysAddress is an octet
string of zero length. Address encoding is as
per [9]. Note that addresses assigned for
purposes other than those listed above (e.g.,
an address associated with the service provider
side of a public network UNI) may be represented
through atmInterfaceAdminAddress.
ifAdminStatus See [5].
ifOperStatus Assumes the value down(2) if the ATM cell
layer or any layer below that layer is down.
Ahmed & Tesink [Page 9]
RFC 1695 ATM Management Objects August 1994
ifLastChange See [5].
ifInOctets The number of received octets over the
interface, i.e., the number of received,
assigned cells multiplied by 53.
ifOutOctets The number of transmitted octets over the
interface, i.e., the number of transmitted,
assigned cells multiplied by 53.
ifInErrors The number of cells dropped due to
uncorrectable HEC errors.
ifInUnknownProtos The number of received cells discarded
during cell header validation, including
cells with unrecognized VPI/VCI values,
and cells with invalid cell header patterns.
If cells with undefined PTI values are discarded,
they are also counted here.
ifOutErrors See [5].
ifName Textual name (unique on this system) of the
interface or an octet string of zero length.
ifLinkUpDownTrapEnable Default is disabled (2).
ifConnectorPresent Set to false (2).
ifPromiscuousMode Set to false(2).
ifHighSpeed See [5].
ifHCInOctets The 64-bit version of ifInOctets; supported
if required by the compliance statements in [5].
ifHCOutOctets The 64-bit version of ifOutOctets; supported
if required by the compliance statements in [5].
7. Support of the AAL3/4 Based Interfaces
For the management of AAL3/4 CPCS layer, see [6].
8. Support of the AAL5 Managed Objects
Support of AAL5 managed objects in an ATM switch and ATM host are
described below.
Ahmed & Tesink [Page 10]
RFC 1695 ATM Management Objects August 1994
8.1. Managing AAL5 in a Switch
Managing AAL5 in a switch involves:
(1) performance management of an AAL5 entity as
an internal resource in a switch
(2) performance management of AAL5 per virtual connection
AAL5 in a switch is modeled as shown in Figures 4 and 5. AAL5 will
be managed in a switch for only those virtual connections that carry
AAL5 and are terminated at the AAL5 entity in the switch. Note that,
the virtual channels within the ATM UNIs carrying AAL5 will be
switched by the ATM switching fabric (termed as ATM Entity in the
figure) to the virtual channels on a proprietary internal interface
associated with the AAL5 process (termed as AAL5 Entity in the
figure). Therefore, performance management of the AAL5 resource in
the switch will be modeled using the ifTable through an internal
(pseudo-ATM) virtual interface and the AAL5 performance management
per virtual connection will be supported using an additional AAL5
connection table in the ATM MIB. The association between the AAL5
virtual link at the proprietary virtual, internal interface and the
ATM virtual link at the ATM interface will be derived from the
virtual channel cross-connect table and the virtual channel link
table in the ATM MIB.
___________________________
| |
| ============= |
| | AAL5 | |
| | Entity | |
| ============= |
| | |
| -----Prop. Virtual Interface
| | |
| ============= |
| | ATM | |
| | Entity | |
| ============= |
|_____|__|__|__|__|_______|
| | | | |
---------------- ATM UNIs
| | | | |
| | | | |
v v v v v
Figure 4 : Model of an AAL5 Entity in a Switch
Ahmed & Tesink [Page 11]
RFC 1695 ATM Management Objects August 1994
__________________
| |
| AAL5 |
|________________|
| |
| Prop. Virtual |
| Interface |
|________________|
Figure 5 : AAL5 Entity's Interface Stack in a Switch
8.2. Managing AAL5 in a Host
Managing AAL5 in a host involves managing the AAL5 sublayer interface
as shown in Figures 6 and 7. The AAL5 sublayer is stacked directly
over the ATM sublayer. The ifTable is applied to the AAL5 sublayer
as defined in Section 8.3.
___________________________
| |
| ============= |
| | AAL5 | |
| | Entity | |
| ============= |
| | ATM | |
| | Entity | |
| ============= |
|___________|_____________|
|
__|__ ATM UNI
|
|
v
Figure 6 : Model of an AAL5 Entity in a Host
__________________
| |
| AAL5 |
|________________|
| |
| ATM Layer |
|________________|
| |
| Physical Layer|
|________________|
Ahmed & Tesink [Page 12]
RFC 1695 ATM Management Objects August 1994
Figure 7 : AAL5 Entity's Interface Stack in a Host
8.3. Support of AAL5 by ifTable
The AAL5 entity in an ATM device (e.g., switch or host) is managed
using the ifTable. There are additional counters specified for AAL5
than those specified in the ATM B-ICI document [10]. Specific
interpretations of ifTable for the AAL5 CPCS layer are as follows.
Object Use for AAL5 CPCS layer entity
====== ==============================
ifIndex Each AAL5 entity is represented by an ifEntry.
ifDescr Description of the AAL5 entity.
ifType The value that is allocated for AAL5 is 49.
ifMtu Set to the largest PDU size for the
AAL5 CPCS layer that can be processed
by the AAL5 entity.
ifSpeed Set to 0.
ifPhysAddress An octet string of zero length.
ifAdminStatus See [5].
ifOperStatus Assumes the value down(2) if the AAL5 or
any layer below that layer is down.
ifLastChange See [5].
ifInOctets The number of received AAL5 CPCS PDU octets.
ifOutOctets The number of AAL5 CPCS PDU octets
transmitted.
ifInUcastPkts The number of received AAL5 CPCS PDUs passed
to a higher-layer.
ifOutUcastPkts The number of AAL5 CPCS PDUs received from a
higher-layer for transmission.
[Note: The number of AAL5 PDUs actually
transmitted is the number received from a
higher-layer for transmission minus any which
are counted by ifOutErrors and ifOutDiscards.]
Ahmed & Tesink [Page 13]
RFC 1695 ATM Management Objects August 1994
ifInErrors Number of errored AAL5 CPCS PDUs received.
The types of errors counted include CRC-32 errors,
SAR time-out errors, and oversized SDU errors.
ifInUnknownProtos Set to 0.
ifInDiscards Number of received AAL5 CPCS PDUs discarded.
Possible reason may be input buffer overflow.
ifOutErrors Number of AAL5 CPCS PDUs that could not
be transmitted due to errors.
ifOutDiscards Number of AAL5 CPCS PDUs received for
transmission that are discarded.
Possible reason may be output buffer
overflow.
ifInMulticastPkts Set to 0.
ifInBroadcastPkts Set to 0.
ifOutMulticastPkts Set to 0.
ifOutBroadcastPkts Set to 0.
ifName Textual name (unique on this system) of the
AAL5 entity or an octet string of zero length.
ifHighSpeed Set to 0.
ifConnectorPresent Set to false (2).
ifPromiscuousMode Set to false(2).
ifLinkUpDownTrapEnable Default is disabled (2).
8.4. Support of Proprietary Virtual Interface by ifTable
Specific interpretations of ifTable for the proprietary virtual,
internal interface associated with an AAL5 entity in an ATM switch
are as follows.
Object Use for proprietary virtual, internal interface
associated with AAL entities
====== ===============================================
ifIndex Each proprietary virtual, internal interface
associated with AAL entities is represented by an
Ahmed & Tesink [Page 14]
RFC 1695 ATM Management Objects August 1994
ifEntry.
ifDescr Description of the proprietary virtual, internal
interface associated with AAL entities.
ifType The value that is allocated for proprietary
virtual, internal interface is 53.
ifSpeed See [5]. Set to 0 if the speed is not
known.
ifPhysAddress See [5]. An octet string of zero length
if no address is used for this interface.
ifAdminStatus See [5].
ifOperStatus See [5].
ifLastChange See [5].
ifName Textual name (unique on this system) of the
interface or an octet string of zero length.
ifHighSpeed See [5]. Set to 0 if the speed is not known.
ifConnectorPresent Set to false (2).
ifLinkUpDownTrapEnable Default is disabled (2).
8.5. AAL5 Connection Performance Statistics Group
An AAL5 connection table is used to provide AAL5 performance
information for each AAL5 virtual connection that is terminated at
the AAL5 entity contained within an ATM switch or host.
9. ILMI MIB and the ATM Managed Objects
The ILMI MIB is specified by the ATM Forum in UNI specification [9],
to manage local ATM UNIs. The support of the ATM management
functions by the ILMI MIB and those contained in this memo are
compared in Table 1. In this table, "yes" in the "ILMI MIB" column
indicates that the management functions are supported by the ILMI
MIB. The MIB groups in the "This memo" column are the groups listed
in Section 5.2.
For that subset of management information which the ILMI MIB and this
memo have in common, every effort has been made to retain identical
semantics and syntax, even though the MIB objects are identified
Ahmed & Tesink [Page 15]
RFC 1695 ATM Management Objects August 1994
using different OBJECT IDENTIFIERs.
Table 1 - Structuring of ATM Managed Objects
______________________________________________________________
| |This |ILMI|
ATM Mgmt.Inf. |ATM Managed Objects |memo |MIB |
______________|_________________________________|_______|____|
Local Interface Information:
_____________________________________________________________
ATM interface:| (1) port identifier |ATM MIB| |
physical layer| (2) physical transmission types | gr.1*|yes*|
configuration | (3) operational status |MIB II | |
| (4) administrative status | | |
| (5) last change status | | |
_____________________________________________________________
ATM interface:| (1) active VPI/VCI fields |ATM MIB| |
cell layer | (2) maximum number of VPCs/VCCs | gr.1 |yes |
configuration | (3) configured VPCs/VCCs | | ** |
| (4) ILMI VPI/VCI values | | |
| (5) ATM address type | | |
| (6) ATM administrative address | | |
_____________________________________________________________
ATM interface:|(1) received/transmitted cells | | |
cell layer |(2) cells with HEC error |MIB II |yes |
performance |(3) cell header validation errors| | |
_____________________________________________________________
ATM interface:|(1)DS3 PLCP severely errored |ATM MIB| |
PLCP & TC | framing seconds | gr.2,3| |
layer |(2)DS3 PLCP unavailable seconds | |no |
performance |(3)DS3 PLCP alarm state | | |
|(4)out of cell delineation events| | |
|(5)TC alarm state | | |
_____________________________________________________________
VP/VC link: |(1)VPI or VPI/VCI value |ATM MIB| |
configuration |(2)VCL or VPL operational status | gr. 4|yes |
|(3)VCL/VPL administrative status | |*** |
|(4)VCL/VPL last change status | | |
|(5)transmit/receive traffic/QoS | | |
| parameters | | |
|(6)AAL type | | |
|(7)transmit/receive AAL5 SDU size| | |
|(8)AAL5 encapsulation type | | |
_____________________________________________________________
Ahmed & Tesink [Page 16]
RFC 1695 ATM Management Objects August 1994
_____________________________________________________________
VP/VC |(1)cross-connect identifier | | |
Cross-connect:|(2)port identifier of one | | |
configuration | end | | |
|(3)port identifier of the other |ATM MIB| |
| end | gr. 5|no |
|(4)VPI or VPI/VCI value | | |
| of one end | | |
|(5)VPI or VPI/VCI value of | | |
| the other end | | |
|(6)VC/VP cross-connect | | |
| operational status | | |
|(7)VC/VP cross-connect | | |
| administrative status | | |
|(8)VC/VP last change status | | |
_____________________________________________________________
VCC AAL5 CPCS |(1)PDUs discarded for CRC errors |ATM MIB| |
layer: |(2)PDUs discarded due to | gr.6 | |
performance | reassembly time out | |no |
|(3)PDUs discarded due to large | | |
| SDUs | | |
_____________________________________________________________
AAL5 entity: |(1)received/transmitted PDUs | | |
|(2)PDUs discarded due to | | |
| protocol errors |MIB II |no |
|(3)a set of configuration/state | | |
| parameters | | |
_____________________________________________________________
*The operational, administrative, and last change status of
the ATM interface and the physical transmission type shall be
supported by the interface table in MIB II (RFC 1213, RFC
1573). ILMI does not contain the administrative and last
change status of the ATM interface.
** The ILMI MIB does not contain information on the ATM
address type and the ATM administrative address assigned at
the ATM interface.
***The ILMI MIB contains local and end-to-end operational
status of the VPC/VCC segment. However, it does not contain
the VPC/VCC administrative and last change status and the VCC
AAL information.
Ahmed & Tesink [Page 17]
RFC 1695 ATM Management Objects August 1994
10. Definitions
ATM-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, OBJECT-IDENTITY,
Counter32, Integer32, IpAddress
FROM SNMPv2-SMI
TEXTUAL-CONVENTION, DisplayString,
TimeStamp, RowStatus
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
ifIndex, mib-2
FROM RFC1213-MIB;
atmMIB MODULE-IDENTITY
LAST-UPDATED "9406072245Z"
ORGANIZATION "IETF AToM MIB Working Group"
CONTACT-INFO
" Masuma Ahmed
Postal: Bellcore
331 Newman Springs Road
Red Bank, NJ 07701
US
Tel: +1 908 758 2515
Fax: +1 908 758 4131
E-mail: mxa@mail.bellcore.com
Kaj Tesink
Postal: Bellcore
331 Newman Springs Road
Red Bank, NJ 07701
US
Tel: +1 908 758 5254
Fax: +1 908 758 4196
E-mail: kaj@cc.bellcore.com"
DESCRIPTION
"This is the MIB Module for ATM and AAL5-related
objects for managing ATM interfaces, ATM virtual
links, ATM cross-connects, AAL5 entities, and
and AAL5 connections."
::= { mib-2 37 }
atmMIBObjects OBJECT IDENTIFIER ::= {atmMIB 1}
-- This ATM MIB Module consists of the following groups:
Ahmed & Tesink [Page 18]
RFC 1695 ATM Management Objects August 1994
-- (1) ATM Interface configuration group
-- (2) ATM Interface DS3 PLCP group
-- (3) ATM Interface TC Sublayer group
-- (4) ATM Interface VPL configuration group
-- (5) ATM Interface VCL configuration group
-- (6) ATM VP Cross Connect group
-- (7) ATM VC Cross Connect group
-- (8) ATM Interface AAL5 VCC performance statistics
-- group
IfIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value of this object identifies the interface
for which the entry contains management
information. The value of this object for a
particular interface has the same value as the
ifIndex object, defined in RFC 1213, for the same
interface."
SYNTAX Integer32
AtmTrafficDescrParamIndex ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The value of this object identifies the row
in the atmTrafficDescrParamTable."
SYNTAX Integer32
atmTrafficDescriptorTypes OBJECT IDENTIFIER ::=
{atmMIBObjects 1}
-- The following values are defined for use as
-- possible values of the ATM traffic descriptor type.
-- ATM Forum specified seven types of ATM traffic
-- descriptors.
atmNoTrafficDescriptor OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This identifies the no ATM traffic descriptor
type. Parameters 1, 2, 3, 4, and 5 are not used.
This traffic descriptor type can be used for
best effort traffic."
::= { atmTrafficDescriptorTypes 1}
atmNoClpNoScr OBJECT-IDENTITY
Ahmed & Tesink [Page 19]
RFC 1695 ATM Management Objects August 1994
STATUS current
DESCRIPTION
"This traffic descriptor is for no CLP and
no Sustained Cell Rate. The use of the
parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: not used
Parameter 3: not used
Parameter 4: not used
Parameter 5: not used.
This traffic descriptor type can be used
for best effort traffic."
::= { atmTrafficDescriptorTypes 2}
atmClpNoTaggingNoScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor is for no CLP without
tagging and no Sustained Cell Rate. The use
of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CLP=0 peak cell rate in
cells per second
Parameter 3: not used
Parameter 4: not used
Parameter 5: not used."
::= { atmTrafficDescriptorTypes 3}
atmClpTaggingNoScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor is for CLP with
tagging and no Sustained Cell Rate. The
use of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CLP=0 peak cell rate in
cells per second with excess
traffic tagged as CLP=1
Parameter 3: not used
Parameter 4: not used
Parameter 5: not used."
::= { atmTrafficDescriptorTypes 4}
atmNoClpScr OBJECT-IDENTITY
STATUS current
Ahmed & Tesink [Page 20]
RFC 1695 ATM Management Objects August 1994
DESCRIPTION
"This traffic descriptor is for no CLP
with Sustained Cell Rate. The
use of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CLP=0+1 sustained cell rate in
cells per second
Parameter 3: CLP=0+1 maximum burst size
in cells
Parameter 4: not used
Parameter 5: not used."
::= { atmTrafficDescriptorTypes 5}
atmClpNoTaggingScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor is for CLP
with Sustained Cell Rate and no tagging.
The use of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CLP=0 sustained cell rate in
cells per second
Parameter 3: CLP=0 maximum burst size in cells
Parameter 4: not used
Parameter 5: not used."
::= { atmTrafficDescriptorTypes 6}
atmClpTaggingScr OBJECT-IDENTITY
STATUS current
DESCRIPTION
"This traffic descriptor is for CLP
with tagging and Sustained Cell Rate.
The use of the parameter vector for this type:
Parameter 1: CLP=0+1 peak cell rate in
cells per second
Parameter 2: CLP=0 sustained cell rate in
cells per second with excess
traffic tagged as CLP=1
Parameter 3: CLP=0 maximum burst size in cells
Parameter 4: not used
Parameter 5: not used."
::= { atmTrafficDescriptorTypes 7}
-- ATM Interface Configuration Parameters Group
Ahmed & Tesink [Page 21]
RFC 1695 ATM Management Objects August 1994
-- This group contains ATM specific
-- configuration information associated with
-- an ATM interface beyond those
-- supported using the ifTable.
atmInterfaceConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmInterfaceConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains ATM local interface
configuration parameters, one entry per ATM
interface port."
::= { atmMIBObjects 2 }
atmInterfaceConfEntry OBJECT-TYPE
SYNTAX AtmInterfaceConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This list contains ATM interface configuration
parameters and state variables."
INDEX { ifIndex }
::= { atmInterfaceConfTable 1}
AtmInterfaceConfEntry ::= SEQUENCE {
atmInterfaceMaxVpcs INTEGER,
atmInterfaceMaxVccs INTEGER,
atmInterfaceConfVpcs INTEGER,
atmInterfaceConfVccs INTEGER,
atmInterfaceMaxActiveVpiBits INTEGER,
atmInterfaceMaxActiveVciBits INTEGER,
atmInterfaceIlmiVpi INTEGER,
atmInterfaceIlmiVci INTEGER,
atmInterfaceAddressType INTEGER,
atmInterfaceAdminAddress OCTET STRING,
atmInterfaceMyNeighborIpAddress IpAddress,
atmInterfaceMyNeighborIfName DisplayString
}
atmInterfaceMaxVpcs OBJECT-TYPE
SYNTAX INTEGER (0..4096)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of VPCs (PVCs and SVCs)
supported at this ATM interface. At the ATM UNI,
Ahmed & Tesink [Page 22]
RFC 1695 ATM Management Objects August 1994
the maximum number of VPCs (PVCs and SVCs)
ranges from 0 to 256 only."
::= { atmInterfaceConfEntry 1}
atmInterfaceMaxVccs OBJECT-TYPE
SYNTAX INTEGER (0..65536)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of VCCs (PVCs and SVCs)
supported at this ATM interface."
::= { atmInterfaceConfEntry 2}
atmInterfaceConfVpcs OBJECT-TYPE
SYNTAX INTEGER (0..4096)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of VPCs (PVCs and SVCs)
configured for use at this ATM interface.
At the ATM UNI, the configured number of
VPCs (PVCs and SVCs) can range from
0 to 256 only."
::= { atmInterfaceConfEntry 3}
atmInterfaceConfVccs OBJECT-TYPE
SYNTAX INTEGER (0..65536)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of VCCs (PVCs and SVCs)
configured for use at the ATM interface."
::= { atmInterfaceConfEntry 4}
atmInterfaceMaxActiveVpiBits OBJECT-TYPE
SYNTAX INTEGER (0..12)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of active VPI bits
configured for use at the ATM interface.
At the ATM UNI, the maximum number of active
VPI bits configured for use ranges from
0 to 8 only."
::= { atmInterfaceConfEntry 5}
atmInterfaceMaxActiveVciBits OBJECT-TYPE
SYNTAX INTEGER (0..16)
Ahmed & Tesink [Page 23]
RFC 1695 ATM Management Objects August 1994
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The maximum number of active VCI bits
configured for use at this ATM interface."
::= { atmInterfaceConfEntry 6}
atmInterfaceIlmiVpi OBJECT-TYPE
SYNTAX INTEGER (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The VPI value of the VCC supporting
the ILMI at this ATM interface. If the values of
atmInterfaceIlmiVpi and atmInterfaceIlmiVci are
both equal to zero then the ILMI is not
supported at this ATM interface."
DEFVAL { 0 }
::= { atmInterfaceConfEntry 7}
atmInterfaceIlmiVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The VCI value of the VCC supporting
the ILMI at this ATM interface. If the values of
atmInterfaceIlmiVpi and atmInterfaceIlmiVci are
both equal to zero then the ILMI is not
supported at this ATM interface."
DEFVAL { 16 }
::= { atmInterfaceConfEntry 8}
atmInterfaceAddressType OBJECT-TYPE
SYNTAX INTEGER {
private(1),
nsapE164(2),
nativeE164(3),
other(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of primary ATM address configured
for use at this ATM interface."
::= { atmInterfaceConfEntry 9 }
atmInterfaceAdminAddress OBJECT-TYPE
Ahmed & Tesink [Page 24]
RFC 1695 ATM Management Objects August 1994
SYNTAX OCTET STRING (SIZE(0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"An address assigned for administrative purposes,
for example, an address associated with the
service provider side of a public network UNI.
If this interface has no assigned administrative
address, or when the address used for
administrative purposes is the same as that used
for ifPhysAddress, then this is an octet string of
zero length."
::= { atmInterfaceConfEntry 10 }
atmInterfaceMyNeighborIpAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The IP address of the neighbor system connected to
the far end of this interface, to which a Network
Management Station can send SNMP messages, as IP
datagrams sent to UDP port 161, in order to access
network management information concerning the
operation of that system. Note that the value
of this object may be obtained in different ways,
e.g., by manual configuration, or through ILMI
interaction with the neighbor system."
::= { atmInterfaceConfEntry 11 }
atmInterfaceMyNeighborIfName OBJECT-TYPE
SYNTAX DisplayString
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The textual name of the interface on the neighbor
system on the far end of this interface, and to
which this interface connects. If the neighbor
system is manageable through SNMP and supports
the object ifName, the value of this object must
be identical with that of ifName for the ifEntry
of the lowest level physical interface
for this port. If this interface does not have a
textual name, the value of this object is a zero
length string. Note that the value of this object
may be obtained in different ways, e.g., by manual
configuration, or through ILMI interaction with
the neighbor system."
Ahmed & Tesink [Page 25]
RFC 1695 ATM Management Objects August 1994
::= { atmInterfaceConfEntry 12 }
-- The ATM Interface DS3 PLCP Group
-- This group contains the DS3 PLCP configuration and
-- state parameters of those ATM interfaces
-- which use DS3 PLCP for carrying ATM cells over DS3.
atmInterfaceDs3PlcpTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmInterfaceDs3PlcpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains ATM interface DS3 PLCP
parameters and state variables, one entry per
ATM interface port."
::= { atmMIBObjects 3}
atmInterfaceDs3PlcpEntry OBJECT-TYPE
SYNTAX AtmInterfaceDs3PlcpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This list contains DS3 PLCP parameters and
state variables at the ATM interface."
INDEX {ifIndex }
::= { atmInterfaceDs3PlcpTable 1}
AtmInterfaceDs3PlcpEntry ::= SEQUENCE {
atmInterfaceDs3PlcpSEFSs Counter32,
atmInterfaceDs3PlcpAlarmState INTEGER,
atmInterfaceDs3PlcpUASs Counter32
}
atmInterfaceDs3PlcpSEFSs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of DS3 PLCP Severely Errored Framing
Second (SEFS). Each SEFS represents a
one-second interval which contains
one or more SEF event."
::= { atmInterfaceDs3PlcpEntry 1}
atmInterfaceDs3PlcpAlarmState OBJECT-TYPE
Ahmed & Tesink [Page 26]
RFC 1695 ATM Management Objects August 1994
SYNTAX INTEGER {
noAlarm(1),
receivedFarEndAlarm(2),
incomingLOF(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if there is an
alarm present for the DS3 PLCP. The value
receivedFarEndAlarm means that the DS3 PLCP
has received an incoming Yellow
Signal, the value incomingLOF means that
the DS3 PLCP has declared a loss of frame (LOF)
failure condition, and the value noAlarm
means that there are no alarms present.
Transition from the failure to the no alarm state
occurs when no defects (e.g., LOF) are received
for more than 10 seconds."
::= { atmInterfaceDs3PlcpEntry 2}
atmInterfaceDs3PlcpUASs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Unavailable Seconds encountered by the PLCP."
::= { atmInterfaceDs3PlcpEntry 3}
-- The ATM Interface TC Sublayer Group
-- This group contains TC sublayer configuration and
-- state parameters of those ATM interfaces
-- which use TC sublayer for carrying ATM cells over
-- SONET or DS3.
atmInterfaceTCTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmInterfaceTCEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains ATM interface TC
Sublayer parameters and state variables,
one entry per ATM interface port."
::= { atmMIBObjects 4}
Ahmed & Tesink [Page 27]
RFC 1695 ATM Management Objects August 1994
atmInterfaceTCEntry OBJECT-TYPE
SYNTAX AtmInterfaceTCEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This list contains TC Sublayer parameters
and state variables at the ATM interface."
INDEX {ifIndex }
::= { atmInterfaceTCTable 1}
AtmInterfaceTCEntry ::= SEQUENCE {
atmInterfaceOCDEvents Counter32,
atmInterfaceTCAlarmState INTEGER
}
atmInterfaceOCDEvents OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of times the Out of Cell
Delineation (OCD) events occur. If seven
consecutive ATM cells have Header Error
Control (HEC) violations, an OCD event occurs.
A high number of OCD events may indicate a
problem with the TC Sublayer."
::= { atmInterfaceTCEntry 1}
atmInterfaceTCAlarmState OBJECT-TYPE
SYNTAX INTEGER {
noAlarm(1),
lcdFailure(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates if there is an
alarm present for the TC Sublayer. The value
lcdFailure indicates that a Loss of
Cell Delineation (LCD) failure state has been
declared for the TC Sublayer. Transition from
failure to the no alarm state occurs
when 6 consecutive ATM cells
are received with valid HEC, followed by
about 10 seconds of acceptable working signal."
::= { atmInterfaceTCEntry 2}
Ahmed & Tesink [Page 28]
RFC 1695 ATM Management Objects August 1994
-- ATM Traffic Descriptor Parameter Group
-- This group contains a set of self-consistent
-- ATM traffic parameters including the
-- ATM traffic QoS Class.
-- The ATM virtual link tables (i.e., VPL and VCL tables)
-- will use this ATM Traffic Descriptor table
-- to assign traffic parameters and QoS Class
-- to the receive and transmit directions of
-- the ATM virtual links (i.e., VPLs and VCLs).
-- The ATM VPL or VCL table will indicate a row
-- in the atmTrafficDescrParamTable
-- using its atmTrafficDescrParamIndex value.
-- The management application can then compare a set of
-- ATM traffic parameters with a single value.
-- If no suitable row(s) in the atmTrafficDescrParamTable
-- exists, the manager must create a new row(s) in this
-- table. If such a row is created, agent checks the
-- sanity of that set of ATM traffic parameter values.
-- When creating a new row, the parameter values
-- will be checked for self-consistency.
-- Predefined/template rows may be supported.
-- A row in the atmTrafficDescrParamTable is deleted
-- by setting the atmTrafficDescrRowStatus to destroy(6).
-- The agent will check whether this row is still in use
-- by any entry of the atmVplTable or atmVclTable.
-- The agent denies the request if the row is still in
-- use.
-- The ATM Traffic Descriptor Parameter Table
atmTrafficDescrParamTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmTrafficDescrParamEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains information on ATM traffic
descriptor type and the associated parameters."
::= { atmMIBObjects 5}
atmTrafficDescrParamEntry OBJECT-TYPE
SYNTAX AtmTrafficDescrParamEntry
MAX-ACCESS not-accessible
Ahmed & Tesink [Page 29]
RFC 1695 ATM Management Objects August 1994
STATUS current
DESCRIPTION
"This list contains ATM traffic descriptor
type and the associated parameters."
INDEX {atmTrafficDescrParamIndex}
::= { atmTrafficDescrParamTable 1}
AtmTrafficDescrParamEntry ::= SEQUENCE {
atmTrafficDescrParamIndex AtmTrafficDescrParamIndex,
atmTrafficDescrType OBJECT IDENTIFIER,
atmTrafficDescrParam1 Integer32,
atmTrafficDescrParam2 Integer32,
atmTrafficDescrParam3 Integer32,
atmTrafficDescrParam4 Integer32,
atmTrafficDescrParam5 Integer32,
atmTrafficQoSClass INTEGER,
atmTrafficDescrRowStatus RowStatus
}
atmTrafficDescrParamIndex OBJECT-TYPE
SYNTAX AtmTrafficDescrParamIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is used by the virtual link
table (i.e., VPL or VCL table)
to identify the row of this table."
::= { atmTrafficDescrParamEntry 1}
atmTrafficDescrType OBJECT-TYPE
SYNTAX OBJECT IDENTIFIER
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the type
of ATM traffic descriptor.
The type may indicate no traffic descriptor or
traffic descriptor with one or more parameters.
These parameters are specified as a parameter
vector, in the corresponding instances of the
objects:
atmTrafficDescrParam1
atmTrafficDescrParam2
atmTrafficDescrParam3
atmTrafficDescrParam4
atmTrafficDescrParam5."
DEFVAL { atmNoTrafficDescriptor }
::= { atmTrafficDescrParamEntry 2}
Ahmed & Tesink [Page 30]
RFC 1695 ATM Management Objects August 1994
atmTrafficDescrParam1 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The first parameter of the ATM traffic descriptor
used according to the value of
atmTrafficDescrType."
DEFVAL { 0 }
::= { atmTrafficDescrParamEntry 3}
atmTrafficDescrParam2 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The second parameter of the ATM traffic descriptor
used according to the value of
atmTrafficDescrType."
DEFVAL { 0 }
::= { atmTrafficDescrParamEntry 4}
atmTrafficDescrParam3 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The third parameter of the ATM traffic descriptor
used according to the value of
atmTrafficDescrType."
DEFVAL { 0 }
::= { atmTrafficDescrParamEntry 5}
atmTrafficDescrParam4 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The fourth parameter of the ATM traffic descriptor
used according to the value of
atmTrafficDescrType."
DEFVAL { 0 }
::= { atmTrafficDescrParamEntry 6}
atmTrafficDescrParam5 OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-create
STATUS current
Ahmed & Tesink [Page 31]
RFC 1695 ATM Management Objects August 1994
DESCRIPTION
"The fifth parameter of the ATM traffic descriptor
used according to the value of
atmTrafficDescrType."
DEFVAL { 0 }
::= { atmTrafficDescrParamEntry 7}
atmTrafficQoSClass OBJECT-TYPE
SYNTAX INTEGER (0..255)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the QoS Class.
Four Service classes have been
specified in the ATM Forum UNI Specification:
Service Class A: Constant bit rate video and
Circuit emulation
Service Class B: Variable bit rate video/audio
Service Class C: Connection-oriented data
Service Class D: Connectionless data
Four QoS classes numbered 1, 2, 3, and 4 have
been specified with the aim to support service
classes A, B, C, and D respectively.
An unspecified QoS Class numbered `0' is used
for best effort traffic."
DEFVAL { 0 }
::= { atmTrafficDescrParamEntry 8}
atmTrafficDescrRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create
a new row or modify or delete an
existing row in this table."
DEFVAL { active }
::= {atmTrafficDescrParamEntry 9}
-- ATM Interface Virtual Path Link (VPL) Group
-- This group contains configuration and state
-- information of a bi-directional Virtual Path Link
-- (VPL)
-- This table can be used to create, delete or modify
Ahmed & Tesink [Page 32]
RFC 1695 ATM Management Objects August 1994
-- a VPL that is terminated in an ATM host or switch.
-- This table can also be used to create, delete or
-- modify a VPL which is cross-connected to another
-- VPL.
-- In the example below, the traffic flows on the receive
-- and transmit directions of the VPLs are characterized
-- by atmVplReceiveTrafficDescrIndex and
-- atmVplTransmitTrafficDescrIndex respectively.
-- The cross-connected VPLs are identified by
-- atmVplCrossConnectIdentifier.
-- ________________________________
-- | |
-- VPL | ATM Host, Switch, or Network | VPL
-- receive | | receive
-- ========> X X <=======
-- <======== X X ========>
-- transmit | | transmit
-- |______________________________|
-- The ATM Interface VPL Table
atmVplTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmVplEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Virtual Path Link (VPL) table. A
bi-directional VPL is modeled as one entry
in this table."
::= { atmMIBObjects 6}
atmVplEntry OBJECT-TYPE
SYNTAX AtmVplEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the VPL table. This entry is
used to model a bi-directional VPL.
To create a VPL at an ATM interface,
either of the following procedures are used:
Ahmed & Tesink [Page 33]
RFC 1695 ATM Management Objects August 1994
Negotiated VPL establishment
(1) The management application creates
a VPL entry in the atmVplTable
by setting atmVplRowStatus to createAndWait(5).
This may fail for the following reasons:
- The selected VPI value is unavailable,
- The selected VPI value is in use.
Otherwise, the agent creates a row and
reserves the VPI value on that port.
(2) The manager selects an existing row(s) in the
atmTrafficDescrParamTable,
thereby, selecting a set of self-consistent
ATM traffic parameters and the QoS Class
for receive and transmit directions of the VPL.
(2a) If no suitable row(s) in the
atmTrafficDescrParamTable exists,
the manager must create a new row(s)
in that table.
(2b) The manager characterizes the VPL's traffic
parameters through setting the
atmVplReceiveTrafficDescrIndex and the
atmVplTransmitTrafficDescrIndex values
in the VPL table, which point to the rows
containing desired ATM traffic parameter values
in the atmTrafficDescrParamTable. The agent
will check the availability of resources and
may refuse the request.
(3) The manager activates the VPL by setting the
the atmVplRowStatus to active(1).
If this set is successful, the agent has
reserved the resources to satisfy the requested
traffic parameter values and the QoS Class
for that VPL.
(4) If the VPL terminates a VPC in the ATM host
or switch, the manager turns on the
atmVplAdminStatus to up(1) to turn the VPL
traffic flow on. Otherwise, the
atmVpCrossConnectTable must be used
to cross-connect the VPL to another VPL(s)
in an ATM switch or network.
One-Shot VPL Establishment
Ahmed & Tesink [Page 34]
RFC 1695 ATM Management Objects August 1994
A VPL may also be established in one step by a
set-request with all necessary VPL parameter
values and atmVplRowStatus set to createAndGo(4).
In contrast to the negotiated VPL establishment
which allows for detailed error checking
(i.e., set errors are explicitly linked to
particular resource acquisition failures),
the one-shot VPL establishment
performs the setup on one operation but
does not have the advantage of step-wise
error checking.
VPL Retirement
A VPL is released by setting atmVplRowStatus to
destroy(6), and the agent may release all
associated resources."
INDEX {ifIndex, atmVplVpi }
::= { atmVplTable 1}
AtmVplEntry ::= SEQUENCE {
atmVplVpi INTEGER,
atmVplAdminStatus INTEGER,
atmVplOperStatus INTEGER,
atmVplLastChange TimeStamp,
atmVplReceiveTrafficDescrIndex
AtmTrafficDescrParamIndex,
atmVplTransmitTrafficDescrIndex
AtmTrafficDescrParamIndex,
atmVplCrossConnectIdentifier INTEGER,
atmVplRowStatus RowStatus
}
atmVplVpi OBJECT-TYPE
SYNTAX INTEGER (1..4095)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VPI value of the VPL.
Note that the VPI=0 is not used
for a VPL not associated with a VCL.
The maximum VPI value cannot
exceed the value allowable by the
atmInterfaceMaxVpiBits."
::= { atmVplEntry 1}
Ahmed & Tesink [Page 35]
RFC 1695 ATM Management Objects August 1994
atmVplAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is implemented only for a VPL which
terminates a VPC (i.e.,
one which is NOT cross-connected to other VPLs).
Its value specifies the desired administrative
state of the VPL. The up and down states indicate
that the traffic flow is enabled and disabled
respectively for this VPL."
DEFVAL { down }
::= { atmVplEntry 2}
atmVplOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
unknown(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the current operational
status of the VPL. The up and down states
indicate that the VPL is currently
operational, or not operational, respectively.
The unknown state indicates that the status of
this VPL cannot be determined."
::= { atmVplEntry 3}
atmVplLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of MIB II's sysUpTime object
at the time this VPL entered its current
operational state. If the current state was
entered prior to the last re-initialization of the
agent, then this object contains a zero value."
::= { atmVplEntry 4 }
Ahmed & Tesink [Page 36]
RFC 1695 ATM Management Objects August 1994
atmVplReceiveTrafficDescrIndex OBJECT-TYPE
SYNTAX AtmTrafficDescrParamIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to the receive direction of the VPL."
::= { atmVplEntry 5}
atmVplTransmitTrafficDescrIndex OBJECT-TYPE
SYNTAX AtmTrafficDescrParamIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row
in the atmTrafficDescrParamTable which
applies to the transmit direction of the VPL."
::= { atmVplEntry 6}
atmVplCrossConnectIdentifier OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is implemented only for a VPL
which is cross-connected to other VPLs
that belong to the same VPC. All such
associated VPLs have the same value of this
object, and all their cross-connections are
identified by entries in the
atmVpCrossConnectTable for which
atmVpCrossConnectIndex has the same value.
The value of this object is initialized by the
agent after the associated entries in the
atmVpCrossConnectTable have been created."
::= {atmVplEntry 7}
atmVplRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create, delete
or modify a row in this table.
To create a new VCL, this object is
initially set to 'createAndWait' or
'createAndGo'. This object must not be
Ahmed & Tesink [Page 37]
RFC 1695 ATM Management Objects August 1994
set to 'active' unless the following columnar
objects exist in this row:
atmVplReceiveTrafficDescrIndex and
atmVplTransmitTrafficDescrIndex."
DEFVAL { active }
::= {atmVplEntry 8}
-- ATM Interface Virtual Channel Link (VCL) Group
-- This group contains configuration and state
-- information of a bi-directional Virtual Channel
-- Link (VCL) at an ATM interface.
-- This table can be used to create, delete or modify
-- a VCL that is terminated in an ATM host or switch.
-- This table can also be
-- used to create, delete or modify a VCL that is
-- cross-connected to another VCL.
-- The ATM Interface VCL Table
atmVclTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmVclEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Virtual Channel Link (VCL) table. A
bi-directional VCL is modeled as one entry
in this table."
::= { atmMIBObjects 7}
atmVclEntry OBJECT-TYPE
SYNTAX AtmVclEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the VCL table. This entry is
used to model a bi-directional VCL.
To create a VCL at an ATM interface,
either of the following procedures are used:
Negotiated VCL establishment
(1) The management application creates
a VCL entry in the atmVclTable
Ahmed & Tesink [Page 38]
RFC 1695 ATM Management Objects August 1994
by setting atmVclRowStatus to createAndWait(5).
This may fail for the following reasons:
- The selected VPI/VCI values are unavailable,
- The selected VPI/VCI values are in use.
Otherwise, the agent creates a row and
reserves the VPI/VCI values on that port.
(2) The manager selects an existing row(s) in the
atmTrafficDescrParamTable,
thereby, selecting a set of self-consistent
ATM traffic parameters and the QoS Class
for receive and transmit directions of the VCL.
(2a) If no suitable row(s) in the
atmTrafficDescrParamTable exists,
the manager must create a new row(s)
in that table.
(2b) The manager characterizes the VCL's traffic
parameters through setting the
atmVclReceiveTrafficDescrIndex and the
atmVclTransmitTrafficDescrIndex values
in the VCL table, which point to the rows
containing desired ATM traffic parameter values
in the atmTrafficDescrParamTable. The agent
will check the availability of resources and
may refuse the request.
(3) The manager activates the VCL by setting the
the atmVclRowStatus to active(1).
If this set is successful, the agent has
reserved the resources to satisfy the requested
traffic parameter values and the QoS Class
for that VCL.
(4) If the VCL terminates a VCC in the ATM host
or switch, the manager turns on the
atmVclAdminStatus to up(1) to turn the VCL
traffic flow on. Otherwise, the
atmVcCrossConnectTable must be used
to cross-connect the VCL to another VCL(s)
in an ATM switch or network.
One-Shot VCL Establishment
A VCL may also be established in one step by a
set-request with all necessary VCL parameter
values and atmVclRowStatus set to createAndGo(4).
Ahmed & Tesink [Page 39]
RFC 1695 ATM Management Objects August 1994
In contrast to the negotiated VCL establishment
which allows for detailed error checking
(i.e., set errors are explicitly linked to
particular resource acquisition failures),
the one-shot VCL establishment
performs the setup on one operation but
does not have the advantage of step-wise
error checking.
VCL Retirement
A VCL is released by setting atmVclRowStatus to
destroy(6), and the agent may release all
associated resources."
INDEX {ifIndex, atmVclVpi, atmVclVci }
::= { atmVclTable 1}
AtmVclEntry ::= SEQUENCE {
atmVclVpi INTEGER,
atmVclVci INTEGER,
atmVclAdminStatus INTEGER,
atmVclOperStatus INTEGER,
atmVclLastChange TimeStamp,
atmVclReceiveTrafficDescrIndex
AtmTrafficDescrParamIndex,
atmVclTransmitTrafficDescrIndex
AtmTrafficDescrParamIndex,
atmVccAalType INTEGER,
atmVccAal5CpcsTransmitSduSize INTEGER,
atmVccAal5CpcsReceiveSduSize INTEGER,
atmVccAal5EncapsType INTEGER,
atmVclCrossConnectIdentifier INTEGER,
atmVclRowStatus RowStatus
}
atmVclVpi OBJECT-TYPE
SYNTAX INTEGER (0..4095)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VPI value of the VCL.
The maximum VPI value cannot
exceed the value allowable by the
atmInterfaceMaxVpiBits."
::= { atmVclEntry 1}
atmVclVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
Ahmed & Tesink [Page 40]
RFC 1695 ATM Management Objects August 1994
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VCI value of the VCL.
The maximum VCI value cannot
exceed the value allowable by the
atmInterfaceMaxVciBits."
::= { atmVclEntry 2}
atmVclAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is implemented only for a VCL which
terminates a VCC (i.e.,
one which is NOT cross-connected to other VCLs).
Its value specifies the desired administrative
state of the VCL. The up and down states indicate
that the traffic flow is enabled and disabled
respectively for this VCL."
::= { atmVclEntry 3}
atmVclOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
unknown(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the current operational
status of the VCL. The up and down states
indicate that the VCL is currently
operational, or not operational, respectively.
The unknown state indicates that the status of
this VCL cannot be determined."
::= { atmVclEntry 4}
atmVclLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Ahmed & Tesink [Page 41]
RFC 1695 ATM Management Objects August 1994
"The value of MIB II's sysUpTime object
at the time this VCL entered its current
operational state. If the current state was
entered prior to the last re-initialization of the
agent, then this object contains a zero value."
::= { atmVclEntry 5 }
atmVclReceiveTrafficDescrIndex OBJECT-TYPE
SYNTAX AtmTrafficDescrParamIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row
in the ATM Traffic Descriptor Table which
applies to the receive direction of this VCL."
::= { atmVclEntry 6}
atmVclTransmitTrafficDescrIndex OBJECT-TYPE
SYNTAX AtmTrafficDescrParamIndex
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the row
of the ATM Traffic Descriptor Table which applies
to the transmit direction of this VCL."
::= { atmVclEntry 7}
atmVccAalType OBJECT-TYPE
SYNTAX INTEGER {
aal1(1),
aal34(2),
aal5(3),
other(4),
unknown(5)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An instance of this object only exists when the
local VCL end-point is also the VCC end-point,
and AAL is in use.
The type of AAL used on this VCC.
The AAL type includes AAL1, AAL3/4,
and AAL5. The other(4) may be user-defined
AAL type. The unknown type indicates that
the AAL type cannot be determined."
::= { atmVclEntry 8 }
Ahmed & Tesink [Page 42]
RFC 1695 ATM Management Objects August 1994
atmVccAal5CpcsTransmitSduSize OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An instance of this object only exists when the
local VCL end-point is also the VCC end-point,
and AAL5 is in use.
The maximum AAL5 CPCS SDU size in octets that is
supported on the transmit direction of this VCC."
DEFVAL { 9188 }
::= { atmVclEntry 9 }
atmVccAal5CpcsReceiveSduSize OBJECT-TYPE
SYNTAX INTEGER (1..65535)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An instance of this object only exists when the
local VCL end-point is also the VCC end-point,
and AAL5 is in use.
The maximum AAL5 CPCS SDU size in octets that is
supported on the receive direction of this VCC."
DEFVAL { 9188 }
::= { atmVclEntry 10 }
atmVccAal5EncapsType OBJECT-TYPE
SYNTAX INTEGER {
vcMultiplexRoutedProtocol(1),
vcMultiplexBridgedProtocol8023(2),
vcMultiplexBridgedProtocol8025(3),
vcMultiplexBridgedProtocol8026(4),
vcMultiplexLANemulation8023(5),
vcMultiplexLANemulation8025(6),
llcEncapsulation(7),
multiprotocolFrameRelaySscs(8),
other(9),
unknown(10)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"An instance of this object only exists when the
local VCL end-point is also the VCC end-point,
and AAL5 is in use.
The type of data encapsulation used over
the AAL5 SSCS layer. The definitions reference
RFC 1483 Multiprotocol Encapsulation
Ahmed & Tesink [Page 43]
RFC 1695 ATM Management Objects August 1994
over ATM AAL5 and to the ATM Forum
LAN Emulation specification."
DEFVAL { llcEncapsulation }
::= { atmVclEntry 11 }
atmVclCrossConnectIdentifier OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object is implemented only for a VCL
which is cross-connected to other VCLs
that belong to the same VCC. All such
associated VCLs have the same value of this
object, and all their cross-connections are
identified by entries in the
atmVcCrossConnectTable for which
atmVcCrossConnectIndex has the same value.
The value of this object is initialized by the
agent after the associated entries in the
atmVcCrossConnectTable have been created."
::= {atmVclEntry 12}
atmVclRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object is used to create, delete or
modify a row in this table. To create
a new VCL, this object is initially set
to 'createAndWait' or 'createAndGo'.
This object must not be set to 'active'
unless the following columnar objects exist
in this row:
atmVclReceiveTrafficDescrIndex,
atmVclTransmitTrafficDescrIndex.
In addition, if the local VCL end-point
is also the VCC end-point:
atmVccAalType.
In addition, for AAL5 connections only:
atmVccAal5CpcsTransmitSduSize,
atmVccAal5CpcsReceiveSduSize, and
atmVccAal5EncapsType."
DEFVAL { active }
::= {atmVclEntry 13}
Ahmed & Tesink [Page 44]
RFC 1695 ATM Management Objects August 1994
-- ATM Virtual Path (VP) Cross Connect Group
-- This group contains configuration and state
-- information of all point-to-point,
-- point-to-multipoint, or multipoint-to-multipoint
-- VP cross-connects.
-- This table has read-create access and can be used
-- to cross-connect the VPLs together in an ATM switch
-- or network. The atmVpCrossConnectIndex
-- is used to associate the related
-- VPLs that are cross-connected together.
-- The ATM VP Cross Connect Group
-- models each bi-directional VPC
-- cross-connect as a set of entries in
-- the atmVpCrossConnectTable. A
-- point-to-point VPC cross-connect is modeled
-- as one entry; a point-to-multipoint (N leafs) VPC
-- cross-connect as N entries in this table; and
-- a multipoint-to-multipoint (N parties) VPC cross-
-- connect as N(N-1)/2 entries in this table.
-- In the latter cases, all the N (or N(N-1)/2) entries
-- are associated with a single VPC cross-connect by
-- having the same value of atmVpCrossConnectIndex.
-- _________________________________________
-- | |
-- Low | ATM Switch or Network | High
-- port| | port
-- _____|>> from low to high VPC traffic flow >>|______
-- |<< from high to low VPC traffic flow <<|
-- | |
-- |_______________________________________|
--
-- The terms low and high are chosen to represent
-- numerical ordering of the two interfaces associated
-- with a VPC cross-connect. That is, the ATM interface
-- with the lower value of ifIndex is termed 'low',
-- while the other ATM interface associated with the
-- VPC cross-connect is termed 'high'. This terminology
-- is used to provide directional information; for
-- example, the atmVpCrossConnectL2HOperStatus applies
-- to the low->high direction, and
-- atmVpCrossConnectH2LOperStatus applies to the
-- high->low direction, as illustrated above.
Ahmed & Tesink [Page 45]
RFC 1695 ATM Management Objects August 1994
atmVpCrossConnectIndexNext OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an appropriate value to
be used for atmVpCrossConnectIndex when creating
entries in the atmVpCrossConnectTable. The value
0 indicates that no unassigned entries are
available. To obtain the atmVpCrossConnectIndex
value for a new entry, the manager issues a
management protocol retrieval operation to obtain
the current value of this object. After each
retrieval, the agent should modify the value to
the next unassigned index."
::= { atmMIBObjects 8 }
-- The ATM VP Cross Connect Table
atmVpCrossConnectTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmVpCrossConnectEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ATM VP Cross Connect table. A bi-
directional VP cross-connect which
cross-connects two VPLs is modeled
as one entry in this table."
::= { atmMIBObjects 9 }
atmVpCrossConnectEntry OBJECT-TYPE
SYNTAX AtmVpCrossConnectEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the ATM VP Cross Connect table.
This entry is used to model a bi-directional
ATM VP cross-connect which cross-connects
two VPLs.
Step-wise Procedures to set up a VP Cross-connect
Once the entries in the atmVplTable are created,
the following procedures are used
to cross-connect the VPLs together.
Ahmed & Tesink [Page 46]
RFC 1695 ATM Management Objects August 1994
(1) The manager obtains a unique
atmVpCrossConnectIndex by reading the
atmVpCrossConnectIndexNext object.
(2) Next, the manager creates a set of one
or more rows in the ATM VP Cross Connect
Table, one for each cross-connection between
two VPLs. Each row is indexed by the ATM
interface port numbers and VPI values of the
two ends of that cross-connection.
This set of rows specifies the topology of the
VPC cross-connect and is identified by a single
value of atmVpCrossConnectIndex.
Negotiated VP Cross-Connect Establishment
(2a) The manager creates a row in this table by
setting atmVpCrossConnectRowStatus to
createAndWait(5). The agent checks the
requested topology and the mutual sanity of
the ATM traffic parameters and
QoS Classes, i.e., the row creation fails if:
- the requested topology is not supported
by the agent,
- the traffic/QoS parameter values
associated with the requested row are
incompatible with those of already existing
rows for this VP cross-connect.
[For example, for setting up
a point-to-point VP cross-connect, the
ATM traffic parameters in the receive direction
of a VPL at the low end of the cross-connect
must equal to the traffic parameters in the
transmit direction of the other VPL at the
high end of the cross-connect,
otherwise, the row creation fails.]
The agent also checks for internal errors
in building the cross-connect.
The atmVpCrossConnectIndex values in the
corresponding atmVplTable rows are filled
in by the agent at this point.
(2b) The manager promotes the row in the
atmVpCrossConnectTable by setting
atmVpCrossConnectRowStatus to active(1). If
this set is successful, the agent has reserved
the resources specified by the ATM traffic
Ahmed & Tesink [Page 47]
RFC 1695 ATM Management Objects August 1994
parameter and QoS Class values
for each direction of the VP cross-connect
in an ATM switch or network.
(3) The manager sets the
atmVpCrossConnectAdminStatus to up(1) in all
rows of this VP cross-connect to turn the
traffic flow on.
One-Shot VP Cross-Connect Establishment
A VP cross-connect may also be established in
one step by a set-request with all necessary
parameter values and atmVpCrossConnectRowStatus
set to createAndGo(4).
In contrast to the negotiated VP cross-connect
establishment which allows for detailed error
checking (i.e., set errors are explicitly linked
to particular resource acquisition failures),
the one-shot VP cross-connect establishment
performs the setup on one operation but does not
have the advantage of step-wise error checking.
VP Cross-Connect Retirement
A VP cross-connect identified by a particular
value of atmVpCrossConnectIndex is released by:
(1) Setting atmVpCrossConnectRowStatus of all
rows identified by this value of
atmVpCrossConnectIndex to destroy(6).
The agent may release all
associated resources, and the
atmVpCrossConnectIndex values in the
corresponding atmVplTable row are removed.
Note that a situation when only a subset of
the associated rows are deleted corresponds
to a VP topology change.
(2) After deletion of the appropriate
atmVpCrossConnectEntries, the manager may
set atmVplRowStatus to destroy(6) the
associated VPLs. The agent releases
the resources and removes the associated
rows in the atmVplTable.
Ahmed & Tesink [Page 48]
RFC 1695 ATM Management Objects August 1994
VP Cross-connect Reconfiguration
At the discretion of the agent, a VP
cross-connect may be reconfigured by
adding and/or deleting leafs to/from
the VP topology as per the VP cross-connect
establishment/retirement procedures.
Reconfiguration of traffic/QoS parameter
values requires release of the VP cross-connect
before those parameter values may by changed
for individual VPLs."
INDEX { atmVpCrossConnectIndex,
atmVpCrossConnectLowIfIndex,
atmVpCrossConnectLowVpi,
atmVpCrossConnectHighIfIndex,
atmVpCrossConnectHighVpi }
::= { atmVpCrossConnectTable 1 }
AtmVpCrossConnectEntry ::= SEQUENCE {
atmVpCrossConnectIndex INTEGER,
atmVpCrossConnectLowIfIndex IfIndex,
atmVpCrossConnectLowVpi INTEGER,
atmVpCrossConnectHighIfIndex IfIndex,
atmVpCrossConnectHighVpi INTEGER,
atmVpCrossConnectAdminStatus INTEGER,
atmVpCrossConnectL2HOperStatus INTEGER,
atmVpCrossConnectH2LOperStatus INTEGER,
atmVpCrossConnectL2HLastChange TimeStamp,
atmVpCrossConnectH2LLastChange TimeStamp,
atmVpCrossConnectRowStatus RowStatus
}
atmVpCrossConnectIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique value to identify this VP cross-connect."
::= { atmVpCrossConnectEntry 1 }
atmVpCrossConnectLowIfIndex OBJECT-TYPE
SYNTAX IfIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of this object is equal to MIB II's
ifIndex value of the ATM interface port for this
VP cross-connect. The term low implies
Ahmed & Tesink [Page 49]
RFC 1695 ATM Management Objects August 1994
that this ATM interface has the numerically lower
ifIndex value than the other ATM interface
identified in the same atmVpCrossConnectEntry."
::= { atmVpCrossConnectEntry 2 }
atmVpCrossConnectLowVpi OBJECT-TYPE
SYNTAX INTEGER (1..4095)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of this object is equal to the VPI
value at the ATM interface
associated with the VP cross-connect that is
identified by atmVpCrossConnectLowIfIndex.
The VPI value cannot exceed the number
supported by the atmInterfaceMaxVpiBits
at the low ATM interface port."
::= { atmVpCrossConnectEntry 3 }
atmVpCrossConnectHighIfIndex OBJECT-TYPE
SYNTAX IfIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of this object is equal to MIB II's
ifIndex value of the ATM interface port for
this VP cross-connect. The term high
implies that this ATM interface has the
numerically higher ifIndex value than the
other ATM interface identified in the same
atmVpCrossConnectEntry."
::= { atmVpCrossConnectEntry 4 }
atmVpCrossConnectHighVpi OBJECT-TYPE
SYNTAX INTEGER (1..4095)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of this object is equal to the VPI
value at the ATM interface associated with
the VP cross-connect that is identified
by atmVpCrossConnectHighIfIndex.
The VPI value cannot exceed the number
supported by the atmInterfaceMaxVpiBits
at the high ATM interface port."
::= { atmVpCrossConnectEntry 5 }
atmVpCrossConnectAdminStatus OBJECT-TYPE
Ahmed & Tesink [Page 50]
RFC 1695 ATM Management Objects August 1994
SYNTAX INTEGER {
up(1),
down(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the desired
administrative status of this bi-directional
VP cross-connect. The up and down states
indicate that the traffic flow is enabled
and disabled respectively on this VP
cross-connect."
DEFVAL { down }
::= { atmVpCrossConnectEntry 6 }
atmVpCrossConnectL2HOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
unknown(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object identifies the current
operational status of the VP cross-connect
in one direction; (i.e., from the low to
high direction). The up and down states indicate
that this ATM VP cross-connect from low
to high direction is operational or not
operational respectively.
The unknown state indicates that
the state of it cannot be determined."
::= { atmVpCrossConnectEntry 7 }
atmVpCrossConnectH2LOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
unknown(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object identifies the current
operational status of the VP cross-connect
in one direction; (i.e., from the high to
Ahmed & Tesink [Page 51]
RFC 1695 ATM Management Objects August 1994
low direction). The up and down states indicate
that this ATM VP cross-connect from high
to low direction is operational or not
operational respectively. The
unknown state indicates that the state
of it cannot be determined."
::= { atmVpCrossConnectEntry 8 }
atmVpCrossConnectL2HLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of MIB II's sysUpTime object
at the time this VP cross-connect entered
its current operational state in the low to
high direction. If the current state was
entered prior to the last re-initialization of the
agent, then this object contains a zero value."
::= { atmVpCrossConnectEntry 9 }
atmVpCrossConnectH2LLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of MIB II's sysUpTime object at the
time this VP cross-connect entered its current
operational state in the high to low direction.
If the current state was entered prior to the
last re-initialization of the agent,
then this object contains a zero value."
::= { atmVpCrossConnectEntry 10 }
atmVpCrossConnectRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this entry in the
atmVpCrossConnectTable. This object is used to
create a cross-connect for cross-connecting
VPLs which are created using the atmVplTable
or to change or delete an existing cross-connect.
This object must be initially set
to `createAndWait' or 'createAndGo'.
This object cannot be set to `active'
unless the following columnar object exists
Ahmed & Tesink [Page 52]
RFC 1695 ATM Management Objects August 1994
in this row: atmVpCrossConnectAdminStatus.
To turn on a VP cross-connect,
the atmVpCrossConnectAdminStatus
is set to `up'."
DEFVAL { active }
::= { atmVpCrossConnectEntry 11 }
-- ATM Virtual Channel (VC) Cross Connect Group
-- This group contains configuration and state
-- information of a bi-directional VC cross-connect.
-- This group is used to model a bi-directional
-- point-to-point, point-to-multipoint or
-- multipoint-to-multipoint VC cross-connects.
-- This table has read-create access and is used
-- to cross-connect the VCLs together in an ATM switch
-- or network that belong to a VC connection.
-- The atmVcCrossConnectIndex is used to associate
-- the related VCLs that are cross-connected together.
-- The step-wise procedures described for setting
-- up a VP cross-connect are also used for setting up
-- a VC cross-connect.
atmVcCrossConnectIndexNext OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object contains an appropriate value to
be used for atmVcCrossConnectIndex when creating
entries in the atmVcCrossConnectTable. The value
0 indicates that no unassigned entries are
available. To obtain the atmVpCrossConnectIndex
value for a new entry, the manager issues a
management protocol retrieval operation to obtain
the current value of this object. After each
retrieval, the agent should modify the value to
the next unassigned index."
::= { atmMIBObjects 10 }
-- The ATM VC Cross Connect Table
Ahmed & Tesink [Page 53]
RFC 1695 ATM Management Objects August 1994
atmVcCrossConnectTable OBJECT-TYPE
SYNTAX SEQUENCE OF AtmVcCrossConnectEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The ATM VC Cross Connect table. A bi-
directional VC cross-connect which
cross-connects two end points (i.e., VCLs)
is modeled as one entry in this table."
::= { atmMIBObjects 11 }
atmVcCrossConnectEntry OBJECT-TYPE
SYNTAX AtmVcCrossConnectEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the ATM VC Cross Connect table.
This entry is used to model a bi-directional ATM
VC cross-connect cross-connecting two end points.
Step-wise Procedures to set up a VC Cross-connect
Once the entries in the atmVclTable are created,
the following procedures are used
to cross-connect the VCLs together to
form a VCC segment.
(1) The manager obtains a unique
atmVcCrossConnectIndex by reading the
atmVcCrossConnectIndexNext object.
(2) Next, the manager creates a set of one
or more rows in the ATM VC Cross Connect
Table, one for each cross-connection between
two VCLs. Each row is indexed by the ATM
interface port numbers and VPI/VCI values of
the two ends of that cross-connection.
This set of rows specifies the topology of the
VCC cross-connect and is identified by a single
value of atmVcCrossConnectIndex.
Negotiated VC Cross-Connect Establishment
(2a) The manager creates a row in this table by
setting atmVcCrossConnectRowStatus to
createAndWait(5). The agent checks the
requested topology and the mutual sanity of
Ahmed & Tesink [Page 54]
RFC 1695 ATM Management Objects August 1994
the ATM traffic parameters and
QoS Classes, i.e., the row creation fails if:
- the requested topology is not supported
by the agent,
- the traffic/QoS parameter values
associated with the requested row are
incompatible with those of already existing
rows for this VC cross-connect.
[For example, for setting up
a point-to-point VC cross-connect, the
ATM traffic parameters in the receive direction
of a VCL at the low end of the cross-connect
must equal to the traffic parameters in the
transmit direction of the other VCL at the
high end of the cross-connect,
otherwise, the row creation fails.]
The agent also checks for internal errors
in building the cross-connect.
The atmVcCrossConnectIndex values in the
corresponding atmVclTable rows are filled
in by the agent at this point.
(2b) The manager promotes the row in the
atmVcCrossConnectTable by setting
atmVcCrossConnectRowStatus to active(1). If
this set is successful, the agent has reserved
the resources specified by the ATM traffic
parameter and QoS Class values
for each direction of the VC cross-connect
in an ATM switch or network.
(3) The manager sets the
atmVcCrossConnectAdminStatus to up(1)
in all rows of this VC cross-connect to
turn the traffic flow on.
One-Shot VC Cross-Connect Establishment
A VC cross-connect may also be established in
one step by a set-request with all necessary
parameter values and atmVcCrossConnectRowStatus
set to createAndGo(4).
In contrast to the negotiated VC cross-connect
establishment which allows for detailed error
checking i.e., set errors are explicitly linked to
Ahmed & Tesink [Page 55]
RFC 1695 ATM Management Objects August 1994
particular resource acquisition failures), the
one-shot VC cross-connect establishment
performs the setup on one operation but does
not have the advantage of step-wise error
checking.
VC Cross-Connect Retirement
A VC cross-connect identified by a particular
value of atmVcCrossConnectIndex is released by:
(1) Setting atmVcCrossConnectRowStatus of all rows
identified by this value of
atmVcCrossConnectIndex to destroy(6).
The agent may release all
associated resources, and the
atmVcCrossConnectIndex values in the
corresponding atmVclTable row are removed.
Note that a situation when only a subset of
the associated rows are deleted corresponds
to a VC topology change.
(2) After deletion of the appropriate
atmVcCrossConnectEntries, the manager may
set atmVclRowStatus to destroy(6) the
associated VCLs. The agent releases
the resources and removes the associated
rows in the atmVclTable.
VC Cross-Connect Reconfiguration
At the discretion of the agent, a VC
cross-connect may be reconfigured by
adding and/or deleting leafs to/from
the VC topology as per the VC cross-connect
establishment/retirement procedures.
Reconfiguration of traffic/QoS parameter
values requires release of the VC cross-connect
before those parameter values may by changed
for individual VCLs."
INDEX { atmVcCrossConnectIndex,
atmVcCrossConnectLowIfIndex,
atmVcCrossConnectLowVpi,
atmVcCrossConnectLowVci,
atmVcCrossConnectHighIfIndex,
atmVcCrossConnectHighVpi,
atmVcCrossConnectHighVci }
::= { atmVcCrossConnectTable 1 }
Ahmed & Tesink [Page 56]
RFC 1695 ATM Management Objects August 1994
AtmVcCrossConnectEntry ::= SEQUENCE {
atmVcCrossConnectIndex INTEGER,
atmVcCrossConnectLowIfIndex IfIndex,
atmVcCrossConnectLowVpi INTEGER,
atmVcCrossConnectLowVci INTEGER,
atmVcCrossConnectHighIfIndex IfIndex,
atmVcCrossConnectHighVpi INTEGER,
atmVcCrossConnectHighVci INTEGER,
atmVcCrossConnectAdminStatus INTEGER,
atmVcCrossConnectL2HOperStatus INTEGER,
atmVcCrossConnectH2LOperStatus INTEGER,
atmVcCrossConnectL2HLastChange TimeStamp,
atmVcCrossConnectH2LLastChange TimeStamp,
atmVcCrossConnectRowStatus RowStatus
}
atmVcCrossConnectIndex OBJECT-TYPE
SYNTAX INTEGER (1..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A unique value to identify this VC cross-connect."
::= { atmVcCrossConnectEntry 1 }
atmVcCrossConnectLowIfIndex OBJECT-TYPE
SYNTAX IfIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of this object is equal to MIB II's
ifIndex value of the ATM interface port for this
VC cross-connect. The term low implies
that this ATM interface has the numerically lower
ifIndex value than the other ATM interface
identified in the same atmVcCrossConnectEntry."
::= { atmVcCrossConnectEntry 2 }
atmVcCrossConnectLowVpi OBJECT-TYPE
SYNTAX INTEGER (0..4095)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of this object is equal to the VPI
value at the ATM interface
associated with the VC cross-connect that is
identified by atmVcCrossConnectLowIfIndex.
The VPI value cannot exceed the number
supported by the atmInterfaceMaxVpiBits
Ahmed & Tesink [Page 57]
RFC 1695 ATM Management Objects August 1994
at the low ATM interface port."
::= { atmVcCrossConnectEntry 3 }
atmVcCrossConnectLowVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of this object is equal to the VCI
value at the ATM interface
associated with this VC cross-connect that is
identified by atmVcCrossConnectLowIfIndex.
The VCI value cannot exceed the number
supported by the atmInterfaceMaxVciBits
at the low ATM interface port."
::= { atmVcCrossConnectEntry 4 }
atmVcCrossConnectHighIfIndex OBJECT-TYPE
SYNTAX IfIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of this object is equal to MIB II's
ifIndex value for the ATM interface port for
this VC cross-connect. The term high
implies that this VC cross-connect
that this ATM interface has the numerically higher
ifIndex value than the other ATM interface
identified in the same atmVcCrossConnectEntry."
::= { atmVcCrossConnectEntry 5 }
atmVcCrossConnectHighVpi OBJECT-TYPE
SYNTAX INTEGER (0..4095)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of this object is equal to the VPI
value at the ATM interface
associated with the VC cross-connect that is
identified by atmVcCrossConnectHighIfIndex.
The VPI value cannot exceed
the number supported by the atmInterfaceMaxVpiBits
at the high ATM interface port."
::= { atmVcCrossConnectEntry 6 }
atmVcCrossConnectHighVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS not-accessible
Ahmed & Tesink [Page 58]
RFC 1695 ATM Management Objects August 1994
STATUS current
DESCRIPTION
"The value of this object is equal to the VCI
value at the ATM interface
associated with the VC cross-connect that is
identified by atmVcCrossConnectHighIfIndex.
The VCI value cannot exceed
the number supported by the atmInterfaceMaxVciBits
at the high ATM interface port."
::= { atmVcCrossConnectEntry 7 }
atmVcCrossConnectAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The value of this object identifies the desired
administrative status of this bi-directional
VC cross-connect. The up and down states
indicate that the traffic flow is enabled or
disabled respectively on this VC cross-connect."
DEFVAL { down }
::= { atmVcCrossConnectEntry 8 }
atmVcCrossConnectL2HOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
unknown(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object identifies the current
operational status of the VC cross-connect
in one direction; (i.e., from the low to
high direction). The up and down states indicate
that this ATM VC cross-connect from low
to high direction is operational or not
operational respectively. The unknown state
indicates that the state of it cannot be
determined."
::= { atmVcCrossConnectEntry 9 }
Ahmed & Tesink [Page 59]
RFC 1695 ATM Management Objects August 1994
atmVcCrossConnectH2LOperStatus OBJECT-TYPE
SYNTAX INTEGER {
up(1),
down(2),
unknown(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object identifies the current
operational status of the VC cross-connect
in one direction; (i.e., from the high to
low direction). The up and down states indicate
that this ATM VC cross-connect from high
to low direction is operational or not
operational respectively. The unknown state
indicates that the state of it cannot be
determined."
::= { atmVcCrossConnectEntry 10 }
atmVcCrossConnectL2HLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of MIB II's sysUpTime object
at the time this VC cross-connect entered
its current operational state in low to high
direction. If the current state was
entered prior to the last re-initialization of the
agent, then this object contains a zero value."
::= { atmVcCrossConnectEntry 11 }
atmVcCrossConnectH2LLastChange OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of MIB II's sysUpTime object
at the time this VC cross-connect entered
its current operational state in high to low
direction. If the current state was
entered prior to the last re-initialization of the
agent, then this object contains a zero value."
::= { atmVcCrossConnectEntry 12 }
atmVcCrossConnectRowStatus OBJECT-TYPE
SYNTAX RowStatus
Ahmed & Tesink [Page 60]
RFC 1695 ATM Management Objects August 1994
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"The status of this entry in the
atmVcCrossConnectTable. This object is used to
create a new cross-connect for cross-connecting
VCLs which are created using the atmVclTable
or to change or delete existing cross-connect.
This object must be initially set to
`createAndWait' or 'createAndGo'. This object
cannot be set to `active' unless the following
columnar object exists in this row:
atmVcCrossConnectAdminStatus.
To turn on a VC cross-connect,
the atmVcCrossConnectAdminStatus
is set to `up'."
::= { atmVcCrossConnectEntry 13 }
-- AAL5 Virtual Channel Connection Performance Statistics
-- Group
-- This group contains the AAL5
-- performance statistics of a VCC at the
-- interface associated with an AAL5 entity in an ATM
-- host or ATM switch.
aal5VccTable OBJECT-TYPE
SYNTAX SEQUENCE OF Aal5VccEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains AAL5 VCC performance
parameters."
::= { atmMIBObjects 12 }
aal5VccEntry OBJECT-TYPE
SYNTAX Aal5VccEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This list contains the AAL5 VCC
performance parameters."
INDEX { ifIndex, aal5VccVpi, aal5VccVci }
::= { aal5VccTable 1 }
Aal5VccEntry ::= SEQUENCE {
Ahmed & Tesink [Page 61]
RFC 1695 ATM Management Objects August 1994
aal5VccVpi INTEGER,
aal5VccVci INTEGER,
aal5VccCrcErrors Counter32,
aal5VccSarTimeOuts Counter32,
aal5VccOverSizedSDUs Counter32
}
aal5VccVpi OBJECT-TYPE
SYNTAX INTEGER (0..4095)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VPI value of the AAL5 VCC at the
interface identified by the ifIndex."
::= { aal5VccEntry 1 }
aal5VccVci OBJECT-TYPE
SYNTAX INTEGER (0..65535)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The VCI value of the AAL5 VCC at the
interface identified by the ifIndex."
::= { aal5VccEntry 2 }
aal5VccCrcErrors OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of AAL5 CPCS PDUs received with
CRC-32 errors on this AAL5 VCC at the
interface associated with an AAL5 entity."
::= { aal5VccEntry 3 }
aal5VccSarTimeOuts OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of partially re-assembled AAL5
CPCS PDUs which were discarded
on this AAL5 VCC at the interface associated
with an AAL5 entity because they
were not fully re-assembled within the
required time period. If the re-assembly
timer is not supported, then this object
Ahmed & Tesink [Page 62]
RFC 1695 ATM Management Objects August 1994
contains a zero value."
::= { aal5VccEntry 4 }
aal5VccOverSizedSDUs OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of AAL5 CPCS PDUs discarded
on this AAL5 VCC at the interface
associated with an AAL5 entity because the
AAL5 SDUs were too large."
::= { aal5VccEntry 5 }
-- Conformance Information
atmMIBConformance OBJECT IDENTIFIER ::= { atmMIB 2 }
atmMIBGroups OBJECT IDENTIFIER
::= { atmMIBConformance 1 }
atmMIBCompliances OBJECT IDENTIFIER
::= { atmMIBConformance 2 }
-- Compliance Statements
atmMIBCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SNMP entities
including networks which have ATM and
AAL5 interfaces."
MODULE -- this module
MANDATORY-GROUPS {atmInterfaceConfGroup,
atmTrafficDescrGroup}
OBJECT atmInterfaceMaxVpcs
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmInterfaceMaxVccs
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
Ahmed & Tesink [Page 63]
RFC 1695 ATM Management Objects August 1994
OBJECT atmInterfaceMaxActiveVpiBits
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmInterfaceMaxActiveVciBits
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmInterfaceIlmiVpi
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmInterfaceIlmiVci
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmInterfaceMyNeighborIpAddress
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmInterfaceMyNeighborIfName
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmTrafficDescrType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmTrafficDescrParam1
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmTrafficDescrParam2
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmTrafficDescrParam3
MIN-ACCESS read-only
DESCRIPTION
Ahmed & Tesink [Page 64]
RFC 1695 ATM Management Objects August 1994
"Write access is not required."
OBJECT atmTrafficDescrParam4
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmTrafficDescrParam5
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmTrafficQoSClass
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmTrafficDescrRowStatus
SYNTAX INTEGER {active(1)}
-- subset of RowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required, and only one
of the six enumerated values for the
RowStatus textual convention need be
supported, specifically: active(1)."
GROUP atmInterfaceDs3PlcpGroup
DESCRIPTION
"This group is mandatory only for those
ATM interfaces which implement the
DS3 PLCP layer."
GROUP atmInterfaceTCGroup
DESCRIPTION
"This group is mandatory only for those
ATM interfaces which implement the
TC Sublayer."
GROUP atmVpcTerminationGroup
DESCRIPTION
"This group is mandatory only for those
ATM interfaces which implement ATM
VPLs that terminate VPCs (i.e., ones which
are NOT cross-connected to other VPLs)."
GROUP atmVpCrossConnectGroup
DESCRIPTION
Ahmed & Tesink [Page 65]
RFC 1695 ATM Management Objects August 1994
"This group is mandatory only for those
ATM interfaces which implement ATM
VPLs that are not associated with VCLs
and are cross-connected to other VPLs."
OBJECT atmVplVpi
SYNTAX INTEGER (1..255)
DESCRIPTION
"For ATM UNIs supporting VPCs, the VPI value
ranges from 1 to 255."
OBJECT atmVplAdminStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmVplReceiveTrafficDescrIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmVplTransmitTrafficDescrIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmVplRowStatus
SYNTAX INTEGER {active(1)}
-- subset of RowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required, and only one
of the six enumerated values for the
RowStatus textual convention need be
supported, specifically: active(1)."
OBJECT atmVpCrossConnectLowVpi
SYNTAX INTEGER (1..255)
DESCRIPTION
"For ATM UNIs supporting VPCs, the VPI value
at the numerically lower ATM interface port
index number ranges from 1 to 255."
OBJECT atmVpCrossConnectHighVpi
SYNTAX INTEGER (1..255)
DESCRIPTION
"For ATM UNIs supporting VPCs, the VPI value
at the numerically higher ATM interface port
Ahmed & Tesink [Page 66]
RFC 1695 ATM Management Objects August 1994
index number ranges from 1 to 255."
OBJECT atmVpCrossConnectAdminStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmVpCrossConnectRowStatus
SYNTAX INTEGER {active(1)}
-- subset of RowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required, and only one
of the six enumerated values for the
RowStatus textual convention need be
supported, specifically: active(1)."
GROUP atmVccTerminationGroup
DESCRIPTION
"This group is mandatory only for those
ATM interfaces which implement ATM
VCLs that terminate VCCs (i.e., ones which
are NOT cross-connected to other VCLs)."
GROUP atmVcCrossConnectGroup
DESCRIPTION
"This group is mandatory only for those
ATM interfaces which implement ATM
VCLs that are cross-connected to
other VCLs."
OBJECT atmVclVpi
SYNTAX INTEGER (0..255)
DESCRIPTION
"For ATM UNIs supporting VCCs, the VPI value
ranges from 0 to 255."
OBJECT atmVclAdminStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmVclReceiveTrafficDescrIndex
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmVclTransmitTrafficDescrIndex
Ahmed & Tesink [Page 67]
RFC 1695 ATM Management Objects August 1994
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmVccAalType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmVclRowStatus
SYNTAX INTEGER {active(1)}
-- subset of RowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required, and only one
of the six enumerated values for the
RowStatus textual convention need be
supported, specifically: active(1)."
OBJECT atmVcCrossConnectLowVpi
SYNTAX INTEGER (0..255)
DESCRIPTION
"For ATM UNIs supporting VCCs, the VPI value
at the numerically lower ATM interface port
index number ranges from 0 to 255."
OBJECT atmVcCrossConnectHighVpi
SYNTAX INTEGER (0..255)
DESCRIPTION
"For ATM UNIs supporting VCCs, the VPI value
at the numerically higher ATM interface port
index number ranges from 0 to 255."
OBJECT atmVcCrossConnectAdminStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmVcCrossConnectRowStatus
SYNTAX INTEGER { active(1)}
-- subset of RowStatus
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required, and only one
of the six enumerated values for the
RowStatus textual convention need be
supported, specifically: active(1)."
Ahmed & Tesink [Page 68]
RFC 1695 ATM Management Objects August 1994
GROUP aal5VccGroup
DESCRIPTION
"This group is mandatory for the
AAL5 virtual connections only."
OBJECT aal5VccVpi
SYNTAX INTEGER (0..255)
DESCRIPTION
"For ATM UNIs supporting AAL5 VCCs,
the VPI value ranges from 0 to 255."
OBJECT atmVccAal5CpcsTransmitSduSize
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmVccAal5CpcsReceiveSduSize
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
OBJECT atmVccAal5EncapsType
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
::= { atmMIBCompliances 1 }
-- Units of Conformance
atmInterfaceConfGroup OBJECT-GROUP
OBJECTS {
atmInterfaceMaxVpcs, atmInterfaceMaxVccs,
atmInterfaceConfVpcs, atmInterfaceConfVccs,
atmInterfaceMaxActiveVpiBits,
atmInterfaceMaxActiveVciBits,
atmInterfaceIlmiVpi,
atmInterfaceIlmiVci,
atmInterfaceAddressType,
atmInterfaceAdminAddress,
atmInterfaceMyNeighborIpAddress,
atmInterfaceMyNeighborIfName}
STATUS current
DESCRIPTION
"A collection of objects providing configuration
information about an ATM interface."
::= { atmMIBGroups 1 }
Ahmed & Tesink [Page 69]
RFC 1695 ATM Management Objects August 1994
atmTrafficDescrGroup OBJECT-GROUP
OBJECTS {
atmTrafficDescrType, atmTrafficDescrParam1,
atmTrafficDescrParam2, atmTrafficDescrParam3,
atmTrafficDescrParam4, atmTrafficDescrParam5,
atmTrafficQoSClass, atmTrafficDescrRowStatus}
STATUS current
DESCRIPTION
"A collection of objects providing information
about ATM traffic descriptor type and
the associated parameters."
::= { atmMIBGroups 2 }
atmInterfaceDs3PlcpGroup OBJECT-GROUP
OBJECTS {atmInterfaceDs3PlcpSEFSs,
atmInterfaceDs3PlcpAlarmState,
atmInterfaceDs3PlcpUASs}
STATUS current
DESCRIPTION
"A collection of objects providing information
about DS3 PLCP layer at an ATM interface."
::= { atmMIBGroups 3 }
atmInterfaceTCGroup OBJECT-GROUP
OBJECTS { atmInterfaceOCDEvents,
atmInterfaceTCAlarmState }
STATUS current
DESCRIPTION
"A collection of objects providing information
about TC sublayer at an ATM interface."
::= { atmMIBGroups 4 }
atmVpcTerminationGroup OBJECT-GROUP
OBJECTS {atmVplOperStatus, atmVplAdminStatus,
atmVplLastChange,
atmVplReceiveTrafficDescrIndex,
atmVplTransmitTrafficDescrIndex,
atmVplRowStatus }
STATUS current
DESCRIPTION
"A collection of objects providing
information about a VPL at an ATM interface
which terminates a VPC
(i.e., one which is NOT cross-connected
to other VPLs)."
::= { atmMIBGroups 5 }
atmVccTerminationGroup OBJECT-GROUP
Ahmed & Tesink [Page 70]
RFC 1695 ATM Management Objects August 1994
OBJECTS {atmVclOperStatus, atmVclAdminStatus,
atmVclLastChange,
atmVclReceiveTrafficDescrIndex,
atmVclTransmitTrafficDescrIndex,
atmVccAalType, atmVclRowStatus }
STATUS current
DESCRIPTION
"A collection of objects providing information
about a VCL at an ATM interface
which terminates a VCC (i.e., one which is
NOT cross-connected to other VCLs)."
::= { atmMIBGroups 6 }
atmVpCrossConnectGroup OBJECT-GROUP
OBJECTS { atmVplReceiveTrafficDescrIndex,
atmVplTransmitTrafficDescrIndex,
atmVplOperStatus, atmVplRowStatus,
atmVpCrossConnectAdminStatus,
atmVpCrossConnectL2HOperStatus,
atmVpCrossConnectH2LOperStatus,
atmVpCrossConnectL2HLastChange,
atmVpCrossConnectH2LLastChange,
atmVpCrossConnectRowStatus,
atmVplCrossConnectIdentifier,
atmVpCrossConnectIndexNext }
STATUS current
DESCRIPTION
"A collection of objects providing
information about a VP cross-connect
and the associated VPLs that are
cross-connected together."
::= { atmMIBGroups 7 }
atmVcCrossConnectGroup OBJECT-GROUP
OBJECTS { atmVclReceiveTrafficDescrIndex,
atmVclTransmitTrafficDescrIndex,
atmVclOperStatus, atmVclRowStatus,
atmVcCrossConnectAdminStatus,
atmVcCrossConnectL2HOperStatus,
atmVcCrossConnectH2LOperStatus,
atmVcCrossConnectL2HLastChange,
atmVcCrossConnectH2LLastChange,
atmVcCrossConnectRowStatus,
atmVclCrossConnectIdentifier,
atmVcCrossConnectIndexNext }
STATUS current
DESCRIPTION
"A collection of objects providing
Ahmed & Tesink [Page 71]
RFC 1695 ATM Management Objects August 1994
information about a VC cross-connect
and the associated VCLs that are
cross-connected together."
::= { atmMIBGroups 8 }
aal5VccGroup OBJECT-GROUP
OBJECTS {atmVccAal5CpcsTransmitSduSize,
atmVccAal5CpcsReceiveSduSize,
atmVccAal5EncapsType,
aal5VccCrcErrors, aal5VccSarTimeOuts,
aal5VccOverSizedSDUs }
STATUS current
DESCRIPTION
"A collection of objects providing
AAL5 configuration and performance statistics
of a VCC."
::= { atmMIBGroups 9 }
END
11. Acknowledgments
This memo is the result of the work of the AToMMIB Working Group. In
particular, the contributions of Keith McCloghrie and Ted Brunner
were critical to the formulation of this specification.
12. References
[1] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure
of Management Information for version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1442, SNMP Research,Inc.,
Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon
University, April 1993.
[2] McCloghrie, K., and M. Rose, Editors, "Management Information
Base for Network Management of TCP/IP-based internets: MIB-II",
STD 17, RFC 1213, Hughes LAN Systems, Performance Systems
International, March 1991.
[3] Galvin, J., and K. McCloghrie, "Administrative Model for version
2 of the Simple Network Management Protocol (SNMPv2)", RFC 1445,
Trusted Information Systems, Hughes LAN Systems, April 1993.
[4] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol
Operations for version 2 of the Simple Network Management
Protocol (SNMPv2)", RFC 1448, SNMP Research, Inc., Hughes LAN
Systems, Dover Beach Consulting, Inc., Carnegie Mellon
University, April 1993.
Ahmed & Tesink [Page 72]
RFC 1695 ATM Management Objects August 1994
[5] McCloghrie, K. and F. Kastenholz, "Evolution of the Interfaces
Group of MIB-II", RFC 1573, Hughes LAN Systems, FTP Software,
January 1994.
[6] Brown, T., and K. Tesink, "Definitions of Managed Objects for
SMDS Interfaces", RFC 1694, Bellcore, August 1994.
[7] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual
Conventions for SNMPv2", RFC 1443, SNMP Research,Inc., Hughes LAN
Systems, Dover Beach Consulting, Inc., Carnegie Mellon
University, April 1993.
[8] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Conformance Statements for SNMPv2", RFC 1444, SNMP
Research,Inc., Hughes LAN Systems, Dover Beach Consulting, Inc.,
Carnegie Mellon University, April 1993.
[9] "ATM Forum UNI Specification, Version 3.0", September 1993.
[10] "ATM Forum B-ICI Specification, Version 1.0", September 1993.
13. Security Considerations
Security issues are not discussed in this memo.
14. Authors' Addresses
Masuma Ahmed
Bell Communications Research
Room 1F-217
331 Newman Springs Road
P.O. Box 7020
Red Bank, NJ 07701-7020
Phone: (908) 758-2515
EMail: mxa@mail.bellcore.com
Kaj Tesink
Bell Communications Research
Room 1A-427
331 Newman Springs Road
P.O. Box 7020
Red Bank, NJ 07701-7020
Phone: (908) 758-5254
EMail: kaj@cc.bellcore.com
Ahmed & Tesink [Page 73]
|
