Network Working Group M. Allen
Request for Comments: 2051 Wall Data Inc.
Category: Standards Track B. Clouston
Z. Kielczewski
Cisco Systems
W. Kwan
Jupiter Technology Inc.
B. Moore
IBM
October 1996
Definitions of Managed Objects for APPC using SMIv2
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Table of Contents
1. Introduction ........................................... 1
2. The SNMP Network Management Framework .................. 1
3. Overview ............................................... 2
3.1 APPC MIB structure ...................................... 4
4. Definitions ............................................ 10
5. Acknowledgments ........................................ 123
6. References ............................................. 123
7. Security Considerations ................................ 123
8. Authors' Addresses ..................................... 124
1. Introduction
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it defines objects for managing the configuration,
monitoring and controlling of network devices with APPC (Advanced
Program-to-Program Communications) capabilities. This memo
identifies managed objects for the SNA LU6.2 protocols.
2. The SNMP Network Management Framework
The SNMP Network Management Framework consists of several components.
For the purpose of this specification, the applicable components of
the Framework are the SMI and related documents [2, 3, 4], which
define the mechanisms used for describing and naming objects for the
Allen, et. al. Standards Track [Page 1]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
purpose of management.
The Framework permits new objects to be defined for the purpose of
experimentation and evaluation.
3. Overview
This document identifies the proposed set of objects for managing the
configuration, monitoring and controlling devices with APPC
capabilities. APPC is the aspect of SNA which supports peer-to-peer
communication, and provides the interface for applications to
communicate. In this document, we will describe LU6.2 protocol-
specific managed objects.
This document describes both dependent and independent LU 6.2
protocols.
A dependent LU requires assistance from an SSCP in order to activate
an LU 6.2 session. An independent LU is able to activate an LU 6.2
session without assistance from the SSCP. If the agent supports
dependent LU 6.2 only, the SNA NAU MIB, RFC 1666 [7] is used instead
to represent those objects.
Local LUs and partner LUs connect with each other using sessions.
Multiple different sessions can be established between LUs with
characteristics defined by Modes. Session limits within a defined
Mode are negotiated between the local and partner LUs using a
protocol called CNOS (Change Number of Sessions).
Transaction Programs (TPs) are applications that use sessions to
communicate with each other. Multiple TPs can use the same session,
but not at the same time. A single usage of a session is called a
conversation. While a session can stay active for a long time, a
conversation can come up and down based on usage by the TPs.
Common Programming Interface - Communications (CPI-C) is a standard
API (Application Programming Interface) for APPC and OSI TP that is
used by TPs for accessing conversations. Although, many of the CPI-C
objects in this MIB are relevant to both APPC and OSI TP, the
intention is for managing APPC products only.
SNA names such as LU names, CP names, mode names, and COS names can
be padded with space characters in SNA formats. These space
characters are insignificant. For example, in a BIND RU a mode name
of "#INTER" with a length of 6 is identical to a mode name of "#INTER
" with a length of 8. However, in this MIB, insignificant space
characters are not included by the agent. Using the mode name from
the previous example, an agent would return a length of 6 and the
Allen, et. al. Standards Track [Page 2]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
string "#INTER" with no space characters for appcModeAdminModeName,
regardless of how it appears in the BIND RU or in internal storage.
The lone exception is the all blank mode name, for which the agent
returns a length of 8 and the string " " (8 space characterss).
When an SNA name is functioning as a table index, an agent shall
treat trailing space characters as significant. If a Management
Station requests the objects from a row with index "#INTER ", the
agent does not match this to the row with index "#INTER". Since an
agent has no insignificant space characters in any of its table
indices, the only reason for a Management Station to include them
would be to start GetNext processing at a chosen point in a table.
For example, a GetNext request with index "M " would start
retrieval from a table at the first row with an 8-character index
beginning with M or a letter after M.
The SNA/APPC terms and overall architecture are documented in [1],
[5], and [6].
Highlights of the management functions supported by the APPC MIB
module include the following:
o Activating and deactivating statistics keeping and counting.
o Activating and deactivating tracing.
o Issuing CNOS processing verbs/commands for
INITIALIZE_SESSION_LIMIT, CHANGE_SESSION_LIMIT and
RESET_SESSION_LIMIT.
o Monitoring of parameters related to local LU, partner LU, modes,
TPs and CPI-C side information.
o Deactivating sessions.
o Monitoring of LU6.2-specific session operational parameters and
statistics, historical information about abnormally terminated
sessions, and information about APPC sessions that are
transported by APPN HPR.
o Monitoring of conversation operational parameters, and
historical information about abnormally terminated sessions.
Allen, et. al. Standards Track [Page 3]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
This MIB module does not support:
o Modifying APPC defaults.
o Creating and deleting partner LUs, modes, TPs, and CPI-C side
information tables.
o Modifying parameters related to local LU, partner LU, modes,
TPs, and CPI-C side information.
o Activating or deactivating local LUs.
o Activating or deactivating partner LUs.
o Activating or deactivating conversations.
o Activating or deactivating Transaction Programs.
o Activating sessions.
o Traps
3.1. APPC MIB Structure
The APPC MIB module contains six groups of objects:
o appcGlobal - objects related to global defaults and controls.
In addition, CNOS processing objects are also part of this group.
o appcLu - objects related to LU6.2-specific local and partner
LU, mode definition, monitoring and control.
o appcTp - objects related to transaction program definition,
monitoring and control.
o appcSession - objects related to LU6.2-specific session
monitoring.
o appcConversation - objects related to conversation monitoring.
o appcCPIC - objects related to related CPI-C side information.
These groups are described below in more detail.
The objects related to LU6.2 are generally organized into two types of
tables: the Admin and Oper tables.
Allen, et. al. Standards Track [Page 4]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
The "Admin" table contains read-only objects which contain default or
expected configuration values. This MIB does not create or modify
configuration values. The "Oper" table contains objects which
provide current operational values, such as state values or
negotiated parameters, for dynamic or configured objects. Dynamic
objects are created by the APPC system using one of the templates
provided in the "Admin" table. Configured objects usually have a
one-to-one relationship between "Admin" and "Oper" entries. However,
some "Admin" values may have changed since the object became
operational, such that the "Oper" values may no longer be based on
the "Admin" values. The "Admin" entry could even be deleted. For
example, some implementations may allow a mode definition
(appcModeAdminEntry) to be deleted even while an active session was
using this mode (appcModeOperEntry still exists). Where appropriate,
the "Oper" table may include initial starting values for objects that
can be reconfigured while operational. How the "Admin" values are
changed or deleted is outside the scope of this MIB.
3.1.1. appcGlobal group
The appcGlobal group consists of the following tables and objects:
1) appcCntrlAdminGroup
This group of objects controls whether certain statistics and
counters (e.g., session counters and RSCV collection) should be
maintained by the Agent. In addition, the ability to activate and
deactivate tracing is also supported through objects in this group.
These objects are for Agent implementations that wish to provide this
level of operational control and are optional.
The objects in this group represent the desired state, with the
actual operational values in appcCntlOperGroup.
These objects can be generated initially, after startup of SNA
service, by the Agent which uses information from the Node
configuration file. Subsequent modifications of object values is
possible by a Management station. The modifications to these objects
can be saved in the Node configuration file for the next startup
(i.e., restart or next initialization) of SNA service, but the
mechanism for this function is not defined in this document.
2) appcCntrlOperGroup
This group of objects monitors whether certain statistics and
counters (e.g., session counters and RSCV collection ) are maintained
by an Agent. In addition, the ability to monitor tracing activity is
also supported through objects in this group.
Allen, et. al. Standards Track [Page 5]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
This table represents the actual operational state. These states can
be modified via objects in the appcCntrlAdminGroup.
3) appcGlobalObjects
These objects describe global information such as APPC system start
time, the control point name, and default LU 6.2 configuration
values. The type of default configuration information includes mode
name, LU, and maximum logical record size.
4) appcCnosControl
These objects allows for issuing of CNOS commands relative to a local
and partner LU pair and a Mode. They support the following CNOS
commands: INITIALIZE_SESSION_LIMIT, CHANGE_SESSION_LIMIT and
RESET_SESSION_LIMIT.
The objects in this group can be modified by a Management Station.
This group consists of objects that are relevant to the CNOS commands
parameters, which a Management Station needs to set. After setting
the parameters of a CNOS command, the Management Station will set the
control object (appcCnosCommand) to request the Agent to issue the
appropriate CNOS command.
3.1.2. appcLu group
The appcLu group consists of the following tables:
1) appcLluAdminTable
This table contains objects which describe specific LU6.2 local LU
configuration information. The type of information includes the
maximum number of sessions supported and compression parameters.
2) appcLluOperTable
This table contains objects which describe specific LU6.2 local LU
operational information. The type of information includes the maximum
number of sessions supported, the number of sessions currently
active, and compression parameters.
3) appcLuPairAdminTable
This table contains objects which describe local LU and partner LU
configuration information. The type of information includes security
information and whether parallel sessions are supported.
Allen, et. al. Standards Track [Page 6]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
For those implementations that have partner LU definitions associated
with each local LU, multiple entries with the same
appcLuPairAdminParLuName could exist with different
appcLuPairAdminLocLuName. For those implementations in which partner
LU definitions apply to all local LUs, the appcLuPairAdminLocLuName
is set to '*ALL'.
4) appcLuPairOperTable
This table contains objects which describe partner/local LU pair run-
time operational information. The type of information includes
security information and whether parallel sessions are supported.
Although the Admin (appcLuPairAdminTable) table entries could be
global to all local LUs in a Node, an entry in this Oper table is
always associated with one local LU.
A row in this table is created as soon as there is an active session
between the local and partner LU. Two entries are present when both
LUs in a pair are local.
5) appcModeAdminTable
This table contains objects which describe Mode configuration
information. The type of information includes the mode name and
maximum session limit.
For those implementations that have Mode definitions associated with
each local and partner LU pair, multiple entries with the same
appcModeAdminModeName could exist with different
appcModeAdminLocLuName and appcModeAdminParLuName. For those
implementations in which Mode definitions apply to all local and/or
all partner LUs, the appcModeAdminLocLuName and/or
appcModeAdminParLuName are set to '*ALL'.
6) appcModeOperTable
This table contains objects which describe Mode run-time operational
information for each local/partner LU pair. The type of information
includes the mode name and maximum session limit.
Although the Admin table entries could be global to all local and
partner LUs in a Node, the Oper table entries are always associated
with one local and partner LU pair.
A row in this table is created as soon as there is an active session
between local and partner LU for this Mode. Two entries are present
when both LUs in a pair are local.
Allen, et. al. Standards Track [Page 7]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
3.1.3. appcTp group
The appcTp group consists of the following table:
1) appcTpAdminTable
This table contains objects which describe transaction program (TP)
configuration information. The type of information includes the TP
name and TP operation, indicating how the TP will be started.
For those implementations that have TP definitions associated with
each local LU, multiple entries with the same appcTpAdminTpName could
exist with different appcTpAdminLocLuName. For those implementations
in which TP definition applies to all local LUs, it will have
appcTpAdminLocLuName set to '*ALL'.
There is no appcTpOperTable. Run-time information about TP tends to
be product-specific (e.g., process Id), and much of the information
can be derived from the conversation tables.
3.1.4. appcSession group
The appcSession group consists of the following tables:
1) appcActSessTable
This table contains objects which describe LU6.2 session information.
The type of information includes the PCID and the pacing counts.
2) appcSessStatsTable
This table contains statistical information about LU 6.2 sessions.
The type of information includes counters of bytes and RUs sent and
received.
3) appcHistSessTable
This table contains historical information about APPC sessions that
have terminated abnormally. The type of information includes the
unbind type and sense data.
4) appcSessRtpTable
This table contains information about LU 6.2 sesions that are being
transported by High Performance Routing. The type of information
includes the NCEID and TCID.
Allen, et. al. Standards Track [Page 8]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
3.1.5. appcConversation group
The appcConversation group consists of the following tables:
1) appcActiveConvTable
This table contains objects which describe active conversation
information. The type of information includes the state and type. An
entry is created by an Agent when the conversation is started, and is
removed when the conversation ends.
2) appcHistConvTable
This table contains objects which describe historical conversation
information about abnormally terminated conversations. The number of
entries and how long they are kept depends on the Agent
implementation. The type of information inclues the sense data and
log data.
3.1.6. appcCPIC group
The appcCPIC group consists of the following tables:
1) appcCpicAdminTable
This table contains objects which describe CPI-C side information.
The type of information includes the symbolic destination name and
partner LU name.
For those implementations that have CPI-C definition associated with
each local LU, multiple entries with the same
appcCpicAdminSymbDestName could exist with different
appcCpicAdminLocLuName. For those implementations in which CPI-C
definition applies to all local LUs, it will have
appcCpicAdminLocLuName set to '*ALL'.
2) appcCpicOperTable
This table contains objects which describe CPI-C run-time operational
information. The type of information includes the symbolic
destination name and partner LU name.
Allen, et. al. Standards Track [Page 9]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
4. Definitions
APPC-MIB DEFINITIONS ::= BEGIN
IMPORTS
DisplayString, InstancePointer, TEXTUAL-CONVENTION, DateAndTime
FROM SNMPv2-TC
mib-2, Counter32, Gauge32, Integer32, TimeTicks,
OBJECT-TYPE, MODULE-IDENTITY
FROM SNMPv2-SMI
snanauMIB
FROM SNA-NAU-MIB
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF;
appcMIB MODULE-IDENTITY
LAST-UPDATED "9512150000Z"
ORGANIZATION "IETF SNA NAU MIB Working Group"
CONTACT-INFO
"
Michael Allen
Wall Data Inc.
P.O.Box 1120
Duval, WA 98019, USA
Tel: 1 206 844 3505
E-mail: mallen@hq.walldata.com
Bob Clouston
Cisco Systems
7025 Kit Creek Road
P.O. Box 14987
Research Triangle Park, NC 27709, USA
Tel: 1 919 472 2333
E-mail: clouston@cisco.com
Zbigniew Kielczewski
Cisco Systems
3100 Smoketree Court
Raleigh, NC 27604, USA
Tel: 1 919 871 6326
E-mail: zbig@cisco.com
Allen, et. al. Standards Track [Page 10]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
William Kwan
Jupiter Technology Inc.
200 Prospect Street
Waltham, MA 02254, USA
Tel: 1 617 894 9300, x423
E-mail: billk@jti.com
Bob Moore
IBM Corporation
800 Park Offices Drive
CNMA/664
P.O. Box 12195
Research Triangle Park, NC 27709, USA
Tel: 1 919 254 4436
E-mail: remoore@ralvm6.vnet.ibm.com
"
DESCRIPTION
"This is the MIB module for objects used to manage network
devices with APPC capabilities."
::= { snanauMIB 3 }
appcObjects OBJECT IDENTIFIER ::= { appcMIB 1 }
appcGlobal OBJECT IDENTIFIER ::= { appcObjects 1 }
appcLu OBJECT IDENTIFIER ::= { appcObjects 2 }
appcTp OBJECT IDENTIFIER ::= { appcObjects 3 }
appcSession OBJECT IDENTIFIER ::= { appcObjects 4 }
appcConversation OBJECT IDENTIFIER ::= { appcObjects 5 }
appcCPIC OBJECT IDENTIFIER ::= { appcObjects 6 }
-- *********************************************************************
-- Objects in this MIB are used to model an SNA device that supports
-- APPC LUs.
-- Following is the overall organization of the MIB.
--
-- 1. APPC Global Objects - global values, defaults,
-- controls (including CNOS)
-- 2. APPC Defined Lu Tables - Admin and Oper
-- 3. APPC Defined LU Pair Tables - Admin and Oper
-- 4. APPC Mode Tables - Admin and Oper
-- 5. APPC TP Tables - Admin only
-- 6. APPC Session Tables - Active, Stats, History, RTP
-- 7. APPC Conversation Table - Active, History
-- 8. APPC CPIC side info - Admin and Oper
-- *********************************************************************
-- *********************************************************************
Allen, et. al. Standards Track [Page 11]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
-- Textual Convention
-- ---------------------------------------------------------------------
SnaSenseData ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"To facilitate their display by a Management Station, sense
data objects in the MIB are represented as DisplayStrings of
size 8. Eight '0' characters indicates that no sense data
identifying an SNA error condition is available."
SYNTAX DisplayString (SIZE (8))
-- *********************************************************************
-- APPC Control Objects
-- ---------------------------------------------------------------------
-- The following objects allow:
-- * the collection of APPC Session information counters
-- to be started and stopped
-- * the collection of APPC Session RSCVs
-- to be started and stopped
-- * the collection of APPC tracing information to be started and
-- stopped
--
-- These objects are for implementations that wish to provide
-- this level of operational control. This group is
-- conditionally mandatory in the conformance section of the MIB.
--
-- *********************************************************************
-- *********************************************************************
-- Control Admin
-- These objects contain the desired states for the controls.
-- The actual states are in the Oper objects.
-- *********************************************************************
appcCntrlAdminGroup OBJECT IDENTIFIER ::= { appcGlobal 1 }
appcCntrlAdminStat OBJECT-TYPE
SYNTAX INTEGER {
notActive(1),
active(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the desired state of statistics collection:
notActive collection of counters is not active.
active collection of counters is active.
Allen, et. al. Standards Track [Page 12]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
When this object is set to notActive, all of the entries are
removed from the appcSessStatsTable."
::= { appcCntrlAdminGroup 1 }
appcCntrlAdminRscv OBJECT-TYPE
SYNTAX INTEGER {
notActive(1),
active(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the desired state of RSCV information collection:
notActive collection of route selection control vectors
is not active.
active collection of route selection control vectors
is active."
::= { appcCntrlAdminGroup 2 }
appcCntrlAdminTrace OBJECT-TYPE
SYNTAX INTEGER {
notActive(1),
active(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Indicates the desired state of tracing:
notActive collection of tracing information is not active
active collection of tracing information is active"
::= { appcCntrlAdminGroup 3 }
appcCntrlAdminTraceParm OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies the parameter to be used in conjunction with
activating tracing. The actual content is implementation
dependent."
::= { appcCntrlAdminGroup 4 }
-- *********************************************************************
Allen, et. al. Standards Track [Page 13]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
-- Control Oper
-- These objects contain the actual states of the controls.
-- *********************************************************************
appcCntrlOperGroup OBJECT IDENTIFIER ::= { appcGlobal 2 }
appcCntrlOperStat OBJECT-TYPE
SYNTAX INTEGER {
notActive(1),
active(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the current collection options in effect:
notActive collection of counters is not active.
active collection of counters is active.
Statistical entries are present in the appcSessStatsTable
only when the value of this object is 'active'."
::= { appcCntrlOperGroup 1 }
appcCntrlOperStatTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since the appcCntrlOperStat object last changed.
This time is in hundreds of a second."
::= { appcCntrlOperGroup 2 }
appcCntrlOperRscv OBJECT-TYPE
SYNTAX INTEGER {
notActive(1),
active(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the current collection options in effect:
notActive collection of route selection control vectors
is not active.
active collection of route selection control vectors
is active."
Allen, et. al. Standards Track [Page 14]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
::= { appcCntrlOperGroup 3 }
appcCntrlOperRscvTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since the appcCntrlOperRscv object last changed.
This time is in hundreds of a second."
::= { appcCntrlOperGroup 4 }
appcCntrlOperTrace OBJECT-TYPE
SYNTAX INTEGER {
notActive(1),
active(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the current state of tracing:
notActive collection of tracing information is not active.
active collection of tracing information is active."
::= { appcCntrlOperGroup 5 }
appcCntrlOperTraceTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Time since the appcCntrlOperTrace object last changed.
This time is in hundreds of a second."
::= { appcCntrlOperGroup 6 }
appcCntrlOperTraceParm OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the parameter used in conjunction with activating
tracing. The actual content is implementation dependent."
::= { appcCntrlOperGroup 7 }
-- ******************************************************************
Allen, et. al. Standards Track [Page 15]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
--
-- APPC global settings
--
-- ******************************************************************
appcGlobalObjects OBJECT IDENTIFIER ::= { appcGlobal 3 }
appcUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time, in hundredths of a second, since the
APPC portion of the system was last reinitialized."
::= { appcGlobalObjects 1 }
appcDefaultModeName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the mode name to be used under the following
conditions:
When an incoming BIND request contains a mode name not
defined at the local node. The parameters defined for
this mode are used for the inbound implicit mode
capability.
When an APPC program issues an [MC_]ALLOCATE,
[MC_]SEND_CONVERSATION, or CNOS verb, or when a CPI-C
program issues an Allocate (CMALLC) call,
specifying a mode name not defined at the local node. The
parameters defined for this mode are used for the outbound
implicit mode capability.
This mode name must match a defined entry in the
appcModeAdminTable."
::= { appcGlobalObjects 2 }
appcDefaultLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the name of the local LU that is to serve as the
default LU. This is the default LU to which are routed inbound
Allen, et. al. Standards Track [Page 16]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
BIND requests that exclude the secondary LU name. This field
is from 1 to 17 characters in length, including a period (.)
which separates the NetId from the NAU name if the NetId is
present. This local LU name must match a defined entry in the
appcLluAdminTable."
::= { appcGlobalObjects 3 }
appcDefaultImplInbndPlu OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether or not inbound implicit partner LU support
is enabled. The following values are defined:
no - Specifies that inbound implicit partner LU support
is disabled, which means that an incoming bind that
specifies a partner LU that is not defined at the
local node will be rejected.
yes - Specifies that inbound implicit partner LU support
is enabled, which provides the capability to accept
an incoming BIND request that contains a partner LU
name that is not defined at the local node."
::= { appcGlobalObjects 4 }
appcDefaultMaxMcLlSndSize OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the maximum size of a logical record to be used for
a mapped conversation when sending data to either the inbound
or outbound implicit partner LU. This size is the maximum
number of bytes in a single logical record, as indicated in the
LL field of the record. The default value is 32767.
Note that this object does not limit the maximum size that an
application program can supply on the Send Data call for a
mapped conversation."
::= { appcGlobalObjects 5 }
Allen, et. al. Standards Track [Page 17]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcDefaultFileSpec OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..80))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local file specification that is to be searched by the
APPC attach manager when no DEFINE_TP verb has been issued
for the TP name received on an incoming attach. In this
case, the attach manager will attempt to start a program
whose file name is the same as the incoming TP name. If
found, the program is loaded. If not found, the attach is
rejected.
The value '*' indicates that the normal search path for
executable programs is to be used for locating an undefined
transaction program.
A null string indicates that there is no default file
specification for undefined transaction programs."
::= { appcGlobalObjects 6 }
appcDefaultTpOperation OBJECT-TYPE
SYNTAX INTEGER {
other(1),
queuedOperatorStarted(2),
queuedOperatorPreloaded(3),
queuedAmStarted(4),
nonqueuedAmStarted(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies how the program will be started.
other - Specifies that the default TP operation is none of
the methods specified below. It may be a
product-specific method.
queuedOperatorStarted - Specifies that one version of the
program will be run at a time. If an incoming
attach arrives and the program has not been started
yet, APPC will issue a message to the operator to
start the specified program. Subsequent attaches
that arrive while the program is active will be
queued.
queuedOperatorPreloaded - Specifies that one version
Allen, et. al. Standards Track [Page 18]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
of the program will be run at a time. If an
incoming attach arrives and the program has not
been started yet, the Attach will be rejected. The
APPC attach manager determines that a TP has
started upon reception of an APPC RECEIVE_ALLOCATE
verb, or a CPI-C Accept_Conversation (CMACCP) or
Specify_Local_TP_Name (CMSLTP) call. No message is
sent to the operator. Subsequent attaches that
arrive while the program is active are queued.
queuedAmStarted - Specifies that one version of the
program will be run at a time and will be started
by the APPC attach manager. Subsequent attaches
that arrive while the program is active will be
queued.
nonqueuedAmStarted - Specifies that multiple copies of
the program will be run at a time and will be
started by the APPC attach manager. "
::= { appcGlobalObjects 7 }
appcDefaultTpConvSecRqd OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether or not conversation security will be used
for default TPs.
no - Specifies that the incoming attach does not have to
contain security information.
yes - Specifies that the incoming attach must contain
valid authentication information (e.g., user ID and
password)."
::= { appcGlobalObjects 8 }
appcLocalCpName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the name of the local control point. This field is
from 0 to 17 characters in length, including a period (.) which
Allen, et. al. Standards Track [Page 19]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
separates the NetId from the NAU name if the NetId is present.
A null string indicates that the value is unknown."
::= { appcGlobalObjects 9 }
appcActiveSessions OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the total number of active APPC sessions supported
by this implementation. Sessions for which both LUs are local
are counted twice."
::= { appcGlobalObjects 10 }
appcActiveHprSessions OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the total number of active HPR APPC sessions."
::= { appcGlobalObjects 11 }
-- ******************************************************************
-- APPC CNOS control
--
-- This group contains objects for issuing APPC Change-Number-of-Session
-- (CNOS) commands to a specific mode. Specifically, the commands
-- supported are:
-- INITIALIZE_SESSION_LIMIT
-- CHANGE_SESSION_LIMIT
-- RESET_SESSION_LIMIT
--
--
-- ******************************************************************
appcCnosControl OBJECT IDENTIFIER ::= { appcGlobal 4 }
appcCnosCommand OBJECT-TYPE
SYNTAX INTEGER {
initSesslimit(1),
changeSesslimit(2),
resetSesslimit(3)
}
MAX-ACCESS read-write
STATUS current
Allen, et. al. Standards Track [Page 20]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
DESCRIPTION
"Specifies the CNOS command or verb to issue. First set the
values of the particular CNOS parameter objects (from the range
{ appcCnosControl 2 } through { appcCnosControl 8 }) that apply
to the CNOS command to be executed, set the three CNOS target
objects ({ appcCnosControl 9 } through { appcCnosControl 11 }),
then set this object to the command to be executed.
Here is the list of parameter objects that must be set for each
of the CNOS commands:
INIT_SESSION_LIMIT -
appcCnosMaxSessLimit
appcCnosMinCwinLimit
appcCnosMinClosLimit
appcCnosTargetLocLuName
appcCnosTargetParLuName
appcCnosTargetModeName
CHANGE_SESSION_LIMIT -
appcCnosMaxSessLimit
appcCnosMinCwinLimit
appcCnosMinClosLimit
appcCnosResponsible
appcCnosTargetLocLuName
appcCnosTargetParLuName
appcCnosTargetModeName
RESET_SESSION_LIMIT -
appcCnosResponsible
appcCnosDrainPart
appcCnosForce
appcCnosTargetLocLuName
appcCnosTargetParLuName
appcCnosTargetModeName
"
::= { appcCnosControl 1 }
appcCnosMaxSessLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies the maximum value that the local LU is to use,
during CNOS processing, for the session limit. The local LU,
as a target LU, will negotiate a higher session limit it
receives in the CNOS request down to this maximum value. The
Allen, et. al. Standards Track [Page 21]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
local LU, as a source LU, will restrict the session limit it
sends in a CNOS request to a value less than or equal to this
maximum value.
If set (i.e., greater than 0), this overrides the maximum
session limit defined in the appcModeAdminTable.
This parameter should be set to the desired value before
setting the command (appcCnosCommand).
This parameter applies to the INITIALIZE_SESSION_LIMIT and
CHANGE_SESSION_LIMIT verbs."
DEFVAL { 0 }
::= { appcCnosControl 2 }
appcCnosMinCwinLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies the default minimum contention winner sessions
limit.
This parameter should be set to the desired value before
setting the command (appcCnosCommand).
This parameter applies to the INITIALIZE_SESSION_LIMIT and
CHANGE_SESSION_LIMIT verbs."
DEFVAL { 0 }
::= { appcCnosControl 3 }
appcCnosMinClosLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies the default minimum contention loser sessions limit.
This parameter should be set to the desired value before
setting the command (appcCnosCommand).
This parameter applies to the INITIALIZE_SESSION_LIMIT and
CHANGE_SESSION_LIMIT verbs."
Allen, et. al. Standards Track [Page 22]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
DEFVAL { 0 }
::= { appcCnosControl 4 }
appcCnosDrainSelf OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies whether the local LU is draining its conversations
for this mode. When a mode session limit is reset (via a CNOS
RESET_SESSION_LIMIT request), the local LU could be set to
process all queued conversations before deactivating all of the
sessions (using the SNA Bracket Initiation Stopped or BIS
protocol).
This parameter should be set to the desired value before
setting the command (appcCnosCommand).
This parameter applies only to the RESET_SESSION_LIMIT verb."
DEFVAL { no }
::= { appcCnosControl 5 }
appcCnosDrainPart OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies whether the partner LU is draining its conversations
for this mode. When a mode session limit is reset (via a CNOS
RESET_SESSION_LIMIT request), the partner LU could be set to
process all queued conversations before deactivating all of the
sessions (using the SNA Bracket Initiation Stop or BIS
protocol).
This parameter should be set to the desired value before
setting the command (appcCnosCommand).
This parameter applies only to the RESET_SESSION_LIMIT verb."
Allen, et. al. Standards Track [Page 23]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
DEFVAL { yes }
::= { appcCnosControl 6 }
appcCnosResponsible OBJECT-TYPE
SYNTAX INTEGER {
source(1),
target(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies which LU is responsible for selecting and
deactivating sessions as a result of a change that decreases
the session limit or the maximum number of contention winner
sessions for the source or target LU. If no session need to be
deactivated, this parameter is ignored.
source - specifies that the source (local) LU is
responsible. The target (partner) LU
cannot negotiate this value.
target - specifies that the target (partner) LU is
responsible. The target LU can negotiate
this value to source.
This parameter should be set to the desired value before
setting the command (appcCnosCommand).
This parameter applies to the RESET_SESSION_LIMIT and
CHANGE_SESSION_LIMIT verbs."
DEFVAL { source }
::= { appcCnosControl 7 }
appcCnosForce OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies whether the local LU should force the resetting of
the session limit when certain error conditions occur that
prevent the successful exchange of CNOS request and reply.
This parameter should be set to the desired value before
Allen, et. al. Standards Track [Page 24]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
setting the command (appcCnosCommand).
This parameter applies only to the RESET_SESSION_LIMIT verb."
DEFVAL { no }
::= { appcCnosControl 8 }
appcCnosTargetLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The SNA name of the local LU to which the CNOS command is
to be applied. This field is from 1 to 17 characters in
length, including a period (.) which separates the
NetId from the NAU name if the NetId is present.
This object should be set to the desired value before setting
the command (appcCnosCommand).
This parameter applies to all CNOS verbs."
::= { appcCnosControl 9 }
appcCnosTargetParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The SNA name of the partner LU to which the CNOS command is
to be applied. This field is from 1 to 17 characters in
length, including a period (.) which separates the
NetId from the NAU name if the NetId is present.
This object should be set to the desired value before setting
the command (appcCnosCommand).
This parameter applies to all CNOS verbs."
::= { appcCnosControl 10 }
appcCnosTargetModeName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Specifies the mode name to which the CNOS command is to be
Allen, et. al. Standards Track [Page 25]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
applied.
This object should be set to the desired value before setting
the command (appcCnosCommand).
This parameter applies to all CNOS verbs."
::= { appcCnosControl 11 }
-- *********************************************************************
-- APPC LU information
-- ---------------------------------------------------------------------
-- Local LU
-- Partner LU
-- Mode
-- *********************************************************************
-- *********************************************************************
-- APPC Local LU
--
-- The entries in the following tables provide information for
-- independent and dependent LU 6.2.
--
-- *********************************************************************
-- *********************************************************************
-- APPC Local LU Admin Table
-- Objects in this table contain default or expected configuration
-- values for local 6.2 LUs.
-- *********************************************************************
appcLluAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcLluAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"APPC Local LU Admin Table."
::= { appcLu 1 }
appcLluAdminEntry OBJECT-TYPE
SYNTAX AppcLluAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about local APPC LUs. "
Allen, et. al. Standards Track [Page 26]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
INDEX { appcLluAdminName }
::= { appcLluAdminTable 1 }
AppcLluAdminEntry ::= SEQUENCE {
appcLluAdminName DisplayString,
appcLluAdminDepType INTEGER,
appcLluAdminLocalAddress OCTET STRING,
appcLluAdminSessLimit Integer32,
appcLluAdminBindRspMayQ INTEGER,
appcLluAdminCompression INTEGER,
appcLluAdminInBoundCompLevel INTEGER,
appcLluAdminOutBoundCompLevel INTEGER,
appcLluAdminCompRleBeforeLZ INTEGER,
appcLluAdminAlias DisplayString
}
appcLluAdminName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the name of the local LU. This field is from 1 to
17 characters in length, including a period (.) which separates
the NetId from the NAU name if the NetId is present."
::= { appcLluAdminEntry 1 }
appcLluAdminDepType OBJECT-TYPE
SYNTAX INTEGER {
dependent(1),
independent(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies whether the LU is dependent or
independent."
::= { appcLluAdminEntry 2 }
appcLluAdminLocalAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local address for this LU is a byte with a value ranging
from 0 to 254. For dependent LUs, this value ranges from 1 to
Allen, et. al. Standards Track [Page 27]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
254; for independent LUs this value is always 0."
::= { appcLluAdminEntry 3 }
appcLluAdminSessLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of sessions supported by this LU."
::= { appcLluAdminEntry 4 }
appcLluAdminBindRspMayQ OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether or not the local LU, as the sender of a BIND
request, allows a partner partner LU to delay sending the BIND
response if the partner LU cannot process the BIND request
immediately."
::= { appcLluAdminEntry 5 }
appcLluAdminCompression OBJECT-TYPE
SYNTAX INTEGER {
prohibited(1),
required(2),
negotiable(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether compression is supported. The local LU uses
this value for negotiation during session activation
(SNA BIND).
prohibited - specifies that no compression is to be used.
required - specifies that compression is required.
negotiable - specifies that the usage of compression
is to be negotiated between the LUs. The
level of compression is also negotiated."
::= { appcLluAdminEntry 6 }
Allen, et. al. Standards Track [Page 28]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcLluAdminInBoundCompLevel OBJECT-TYPE
SYNTAX INTEGER {
none(1),
rle(2),
lz9(3),
lz10(4),
lz12(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the maximum level of compression supported for
inbound data. The local LU uses this value in conjunction with
appcLluAdminCompression for negotiation during session
activation (SNA BIND).
none - specifies that no compression is to be used.
rle - specifies run-length encoding compression
in which a 1 or 2 byte sequence substitution is
used for each repeated run of the same character.
lz9 - specifies Lempel-Ziv-like compression in which
9 bit codes are used to substitute repeated
substrings in the data stream. These codes are
indices that refer to entries in a common
dictionary generated adaptively at both sender and
receiver as the data flows and compression occurs.
The larger number bits used for the code, the more
storage space is required for the dictionary, but
the larger the compression ratio.
lz10 - specifies a 10 bit code Lempel-Ziv-like compression.
lz12 - specifies a 12 bit code Lempel-Ziv-like compression."
::= { appcLluAdminEntry 7 }
appcLluAdminOutBoundCompLevel OBJECT-TYPE
SYNTAX INTEGER {
none(1),
rle(2),
lz9(3),
lz10(4),
lz12(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the maximum level of compression supported for
outbound data. The local LU uses this value in conjunction
with appcLluAdminCompression for negotiation during session
activation (SNA BIND).
Allen, et. al. Standards Track [Page 29]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
none - specifies that no compression is to be used.
rle - specifies run-length encoding compression
in which a 1 or 2 byte sequence substitution is
used for each repeated run of the same character.
lz9 - specifies Lempel-Ziv-like compression in which
9 bit codes are used to substitute repeated
substrings in the data stream. These codes are
indices that refer to entries in a common
dictionary generated adaptively at both sender and
receiver as the data flows and compression occurs.
The larger of number bits used for the code, the
more storage space is required for the dictionary,
but the larger the compression ratio.
lz10 - specifies a 10 bit code Lempel-Ziv-like compression.
lz12 - specifies a 12 bit code Lempel-Ziv-like compression."
::= { appcLluAdminEntry 8 }
appcLluAdminCompRleBeforeLZ OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether run-length encoding is to be applied to the
data before applying Lempel-Ziv-like compression. The local LU
uses this value for negotiation during session activation (SNA
BIND). This parameter is only supported if LZ compression is
used."
::= { appcLluAdminEntry 9 }
appcLluAdminAlias OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A local alias for the local LU. If not known or
not applicable, this object contains a zero-length
string."
::= { appcLluAdminEntry 10 }
-- *********************************************************************
-- APPC Local LU Oper Table
Allen, et. al. Standards Track [Page 30]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
-- Objects in this table contain current operational values, such
-- as state values or negotiated parameters, for local 6.2 LUs.
-- *********************************************************************
appcLluOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcLluOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"APPC Local LU Operational Table."
::= { appcLu 2 }
appcLluOperEntry OBJECT-TYPE
SYNTAX AppcLluOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Information about local APPC LUs."
INDEX { appcLluOperName }
::= { appcLluOperTable 1 }
AppcLluOperEntry ::= SEQUENCE {
appcLluOperName DisplayString,
appcLluOperDepType INTEGER,
appcLluOperLocalAddress OCTET STRING,
appcLluOperSessLimit Integer32,
appcLluOperBindRspMayQ INTEGER,
appcLluOperCompression INTEGER,
appcLluOperInBoundCompLevel INTEGER,
appcLluOperOutBoundCompLevel INTEGER,
appcLluOperCompRleBeforeLZ INTEGER,
appcLluOperAlias DisplayString,
appcLluOperActiveSessions Gauge32
}
appcLluOperName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the name of the local LU. This field is from 1 to
17 characters in length, including a period (.) which separates
the NetId from the NAU name if the NetId is present."
::= { appcLluOperEntry 1 }
Allen, et. al. Standards Track [Page 31]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcLluOperDepType OBJECT-TYPE
SYNTAX INTEGER {
dependent(1),
independent(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies whether the LU is dependent or
independent."
::= { appcLluOperEntry 2 }
appcLluOperLocalAddress OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local address for this LU is a byte with a value ranging
from 0 to 254. For dependent LUs, this value ranges from 1 to
254; for independent LUs this value is always 0."
::= { appcLluOperEntry 3 }
appcLluOperSessLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of sessions supported by this LU."
::= { appcLluOperEntry 4 }
appcLluOperBindRspMayQ OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether or not the local LU, as the sender of a BIND
request, allows a partner LU to delay sending the BIND
response if the partner LU cannot process the BIND request
immediately."
::= { appcLluOperEntry 5 }
Allen, et. al. Standards Track [Page 32]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcLluOperCompression OBJECT-TYPE
SYNTAX INTEGER {
prohibited(1),
required(2),
negotiable(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether compression is supported. The local LU uses
this value for negotiation during session activation (SNA
BIND).
prohibited - specifies that no compression is to be used.
required - specifies that compression is required.
negotiable - specifies that the usage of compression
is to be negotiated between the LUs. The
level of compression is also negotiated."
::= { appcLluOperEntry 6 }
appcLluOperInBoundCompLevel OBJECT-TYPE
SYNTAX INTEGER {
none(1),
rle(2),
lz9(3),
lz10(4),
lz12(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the maximum level of compression supported for
inbound data. The local LU uses this value in conjunction with
appcLluOperCompression for negotiation during session
activation (SNA BIND).
none - specifies that no compression is to be used.
rle - specifies run-length encoding compression
in which a 1 or 2 byte sequence substitution is
used for each repeated run of the same character.
lz9 - specifies Lempel-Ziv-like compression in which
9 bit codes are used to substitute repeated
substrings in the data stream. These codes are
indices that refer to entries in a common
dictionary generated adaptively at both sender and
receiver as the data flows and compression occurs.
The larger of number bits used for the code, the
Allen, et. al. Standards Track [Page 33]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
more storage space is required for the dictionary,
but the larger the compression ratio.
lz10 - specifies a 10 bit code Lempel-Ziv-like compression.
lz12 - specifies a 12 bit code Lempel-Ziv-like compression."
::= { appcLluOperEntry 7 }
appcLluOperOutBoundCompLevel OBJECT-TYPE
SYNTAX INTEGER {
none(1),
rle(2),
lz9(3),
lz10(4),
lz12(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the maximum level of compression supported for
outbound data. The local LU uses this value in conjunction
with appcLluAdminCompression for negotiation during session
activation (SNA BIND).
none - specifies that no compression is to be used.
rle - specifies run-length encoding compression
in which a 1 or 2 byte sequence substitution is
used for each repeated run of the same character.
lz9 - specifies Lempel-Ziv-like compression in which
9 bit codes are used to substitute repeated
substrings in the data stream. These codes are
indices that refer to entries in a common
dictionary generated adaptively at both sender and
receiver as the data flows and compression occurs.
The larger of number bits used for the code, the
more storage space is required for the dictionary,
but the larger the compression ratio.
lz10 - specifies a 10 bit code Lempel-Ziv-like compression.
lz12 - specifies a 12 bit code Lempel-Ziv-like compression."
::= { appcLluOperEntry 8 }
appcLluOperCompRleBeforeLZ OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Allen, et. al. Standards Track [Page 34]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
"Specifies whether run-length encoding is to be applied to the
data before applying Lempel-Ziv-like compression. The local LU
uses this value for negotiation during session activation (SNA
BIND). This parameter is only supported if LZ compression is
used."
::= { appcLluOperEntry 9 }
appcLluOperAlias OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A local alias for the local LU. If not known or
not applicable, this object contains a zero-length
string."
::= { appcLluOperEntry 10 }
appcLluOperActiveSessions OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the total number of active APPC sessions for this
LU."
::= { appcLluOperEntry 11 }
-- *********************************************************************
-- APPC LU Pair Admin Table
-- Objects in this table contain default or expected configuration
-- values for 6.2 LU pairs. An LU pair consists of a local LU and
-- a partner LU, which may or may not be local.
-- *********************************************************************
appcLuPairAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcLuPairAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"APPC Partner LU administrative Table"
::= { appcLu 3 }
appcLuPairAdminEntry OBJECT-TYPE
SYNTAX AppcLuPairAdminEntry
MAX-ACCESS not-accessible
STATUS current
Allen, et. al. Standards Track [Page 35]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
DESCRIPTION
"Entry of APPC Partner LU Information Table.
It is indexed by the local and partner LU Names."
INDEX { appcLuPairAdminLocLuName,
appcLuPairAdminParLuName }
::= { appcLuPairAdminTable 1 }
AppcLuPairAdminEntry ::= SEQUENCE {
appcLuPairAdminLocLuName DisplayString,
appcLuPairAdminParLuName DisplayString,
appcLuPairAdminParLuAlias DisplayString,
appcLuPairAdminSessLimit Integer32,
appcLuPairAdminSessSec INTEGER,
appcLuPairAdminSecAccept INTEGER,
appcLuPairAdminLinkObjId InstancePointer,
appcLuPairAdminParaSessSup INTEGER
}
appcLuPairAdminLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNA name of the local LU to which this partner LU
definition applies. This field is from 1 to 17 characters in
length, including a period (.) which separates the
NetId from the NAU name if the NetId is present.
The reserved value '*ALL' indicates that the partner LU
definition applies to all local LUs, and not just to a single
local LU."
::= { appcLuPairAdminEntry 1 }
appcLuPairAdminParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNA name of the partner LU.
This field is from 1 to 17 characters in
length, including a period (.) which separates the
NetId from the NAU name if the NetId is present."
Allen, et. al. Standards Track [Page 36]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
::= { appcLuPairAdminEntry 2 }
appcLuPairAdminParLuAlias OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A local alias for the partner LU. If not known or
not applicable, this object contains a zero-length
string."
::= { appcLuPairAdminEntry 3 }
appcLuPairAdminSessLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of sessions supported by this partner LU."
::= { appcLuPairAdminEntry 4 }
appcLuPairAdminSessSec OBJECT-TYPE
SYNTAX INTEGER {
required(1),
accepted(2),
notAllowed(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the type of session-level security information that
a local LU will accept on BIND requests it receives from the
partner LU.
required - Specifies that the BIND request must carry
session level verification information that
will be verified upon receipt.
accepted - Specifies that the BIND request may carry
session level verification information that
will be verified upon receipt.
notAllowed - Specifies that the BIND request must not carry
session level verification information."
::= { appcLuPairAdminEntry 5 }
appcLuPairAdminSecAccept OBJECT-TYPE
SYNTAX INTEGER {
Allen, et. al. Standards Track [Page 37]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
none(1),
conversation(2),
alreadyVerified(3),
persistentVerification(4),
aVandpV(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies support for different levels of access security
information in ATTACH requests received from this partner LU.
Possible values are:
none - No access security information will be
accepted on allocation requests (ATTACH) from
this LU.
conversation
- Allocation requests will not be accepted that
include already verified or persistent
verification indicators. Accept
conversation-level access security
information, which must include both a user
Id and password, and may also include a
profile.
alreadyVerified
- Allocation requests will be accepted that
include already verified indicators.
Persistent verification indicators will not
be accepted.
persistentVerification
- Allocation requests will be accepted that
include persistent verification indicators.
Already verified indicators will not be
accepted.
aVandpV - Allocation requests will be accepted that
include already verified or persistent
verification indicators."
::= { appcLuPairAdminEntry 6 }
appcLuPairAdminLinkObjId OBJECT-TYPE
SYNTAX InstancePointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the link associated with this partner LU. This
value points to the row in the table containing information on
Allen, et. al. Standards Track [Page 38]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
the link instance. (e.g., the sdlcLSAdminTable of the SNA DLC
MIB module). This object may be NULL if the link is not
specified or if a link is not applicable (as for APPN-level
nodes)."
::= { appcLuPairAdminEntry 7 }
appcLuPairAdminParaSessSup OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Defined Parallel Sessions Supported.
Indicates whether or not multiple sessions between the partner
LU and its associated local LU are permitted. Parallel session
support also indicates that Change Number of Sessions (CNOS)
will be used to negotiate session limits between the LUs."
::= { appcLuPairAdminEntry 8 }
-- *********************************************************************
-- APPC LU Pair Oper Table
-- Objects in this table contain current operational values, such
-- as state values or negotiated parameters, for 6.2 LU pairs.
-- *********************************************************************
appcLuPairOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcLuPairOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of active partner/local LU pairs. Two entries are
present in the table when both LUs in a pair are local."
::= { appcLu 4 }
appcLuPairOperEntry OBJECT-TYPE
SYNTAX AppcLuPairOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry representing one partner/local LU pair."
INDEX { appcLuPairOperLocLuName,
Allen, et. al. Standards Track [Page 39]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcLuPairOperParLuName }
::= { appcLuPairOperTable 1 }
AppcLuPairOperEntry ::= SEQUENCE {
appcLuPairOperLocLuName DisplayString,
appcLuPairOperParLuName DisplayString,
appcLuPairOperParLuAlias DisplayString,
appcLuPairOperSessLimit Integer32,
appcLuPairOperSessSec INTEGER,
appcLuPairOperSecAccept INTEGER,
appcLuPairOperLinkObjId InstancePointer,
appcLuPairOperParaSessSup INTEGER,
appcLuPairOperParaSessSupLS INTEGER,
appcLuPairOperState INTEGER
}
appcLuPairOperLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNA name of the local LU. This field is from 1 to 17
characters in length, including a period (.) which separates
the NetId from the NAU name if the NetId is present.
If this object has the same value as appcLluOperName,
then the two entries being indexed apply to the same
resource (specifically, to the same local LU)."
::= { appcLuPairOperEntry 1 }
appcLuPairOperParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNA name of the partner LU.
This field is from 1 to 17 characters in
length, including a period (.) which separates the
NetId from the NAU name if the NetId is present."
::= { appcLuPairOperEntry 2 }
appcLuPairOperParLuAlias OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..8))
MAX-ACCESS read-only
STATUS current
Allen, et. al. Standards Track [Page 40]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
DESCRIPTION
"A local alias for the partner LU. If not known or
not applicable, this object contains a zero-length
string."
::= { appcLuPairOperEntry 3 }
appcLuPairOperSessLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of sessions supported by this partner LU."
::= { appcLuPairOperEntry 4 }
appcLuPairOperSessSec OBJECT-TYPE
SYNTAX INTEGER {
required(1),
accepted(2),
notAllowed(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the type of security information that a local LU
will accept on BIND requests it receives from the partner LU.
required - Specifies that the BIND request must carry
session level verification information that
will be verified upon receipt.
accepted - Specifies that the BIND request may carry
session level verification information that
will be verified upon receipt.
notAllowed - Specifies that the BIND request must not carry
session level verification information."
::= { appcLuPairOperEntry 5 }
appcLuPairOperSecAccept OBJECT-TYPE
SYNTAX INTEGER {
none(1),
conversation(2),
alreadyVerified(3),
persistentVerification(4),
aVandpV(5)
}
MAX-ACCESS read-only
Allen, et. al. Standards Track [Page 41]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
STATUS current
DESCRIPTION
"Specifies support for different levels of security acceptance
information in ATTACH requests received from this partner LU.
Possible values are:
none - No access security information will be
accepted on allocation requests (ATTACH) from
this LU.
conversation
- Allocation requests will not be accepted that
include already verified or persistent
verification indicators. Accept
conversation-level access security
information, which must include both a user
Id and password, and may also include a
profile.
alreadyVerified
- Allocation requests will be accepted that
include already verified indicators.
Persistent verification indicators will not
be accepted.
persistentVerification
- Allocation requests will be accepted that
include persistent verification indicators.
Already verified indicators will not be
accepted.
aVandpV - Allocation requests will be accepted that
include already verified or persistent
verification indicators."
::= { appcLuPairOperEntry 6 }
appcLuPairOperLinkObjId OBJECT-TYPE
SYNTAX InstancePointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the link associated with this partner LU. This
value points to the row in the table containing information on
the link instance. (e.g., the sdlcLSAdminTable of the SNA DLC
MIB module). This object may be NULL if the link is not
specified or if a link is not applicable (as for APPN-level
nodes)."
::= { appcLuPairOperEntry 7 }
appcLuPairOperParaSessSup OBJECT-TYPE
Allen, et. al. Standards Track [Page 42]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Active Parallel Sessions Supported.
Indicates whether or not multiple session between the partner
LU and its associated local LU are permitted. Parallel
session support also indicates that Change Number of Sessions
(CNOS) will be used to negotiate session limits between the
LUs."
::= { appcLuPairOperEntry 8 }
appcLuPairOperParaSessSupLS OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Active Parallel Sessions Supported - last starting value.
This object represents the initial value proposed by the local
LU the last time this capability was negotiated, i.e., when
the first session was bound between the local LU and its
partner."
::= { appcLuPairOperEntry 9 }
appcLuPairOperState OBJECT-TYPE
SYNTAX INTEGER {
inactive (1),
active (2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value identifies the current operational state of this LU
pair:
inactive (1) - no active or pending session exists
between the LUs.
active (2) - an active or pending session exists
Allen, et. al. Standards Track [Page 43]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
between the LUs."
::= { appcLuPairOperEntry 10 }
-- *********************************************************************
-- APPC Mode Admin Table
-- Objects in this table contain default or expected configuration
-- values for session modes.
-- Modes that have active sessions appear in the appcModeOperTable.
-- *********************************************************************
appcModeAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcModeAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"APPC Mode Table"
::= { appcLu 5 }
appcModeAdminEntry OBJECT-TYPE
SYNTAX AppcModeAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry of APPC Mode Information Table."
INDEX { appcModeAdminLocLuName,
appcModeAdminParLuName,
appcModeAdminModeName }
::= { appcModeAdminTable 1 }
AppcModeAdminEntry ::= SEQUENCE {
appcModeAdminLocLuName DisplayString,
appcModeAdminParLuName DisplayString,
appcModeAdminModeName DisplayString,
appcModeAdminCosName DisplayString,
appcModeAdminSessEndTpName DisplayString,
appcModeAdminMaxSessLimit Integer32,
appcModeAdminMinCwinLimit Integer32,
appcModeAdminMinClosLimit Integer32,
appcModeAdminConWinAutoActLmt Integer32,
appcModeAdminRecvPacWinSz Integer32,
appcModeAdminSendPacWinSz Integer32,
appcModeAdminPrefRecvRuSz Integer32,
appcModeAdminPrefSendRuSz Integer32,
appcModeAdminRecvRuSzUpBnd Integer32,
appcModeAdminSendRuSzUpBnd Integer32,
Allen, et. al. Standards Track [Page 44]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcModeAdminRecvRuSzLoBnd Integer32,
appcModeAdminSendRuSzLoBnd Integer32,
appcModeAdminSingSessReinit INTEGER,
appcModeAdminCompression INTEGER,
appcModeAdminInBoundCompLevel INTEGER,
appcModeAdminOutBoundCompLevel INTEGER,
appcModeAdminCompRleBeforeLZ INTEGER,
appcModeAdminSyncLvl INTEGER,
appcModeAdminCrypto INTEGER
}
appcModeAdminLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNA name of the local LU to which this mode definition
applies. This field is from 1 to 17 characters in length,
including a period (.) which separates the NetId from the
NAU name if the NetId is present.
The reserved value '*ALL' indicates that the mode definition
applies to all local LUs for the SNA node identified by
appcLocalCpName, and not just to a single local LU."
::= { appcModeAdminEntry 1 }
appcModeAdminParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNA name of the partner LU to which this mode definition
applies. This field is from 1 to 17 characters in length,
including a period (.) which separates the NetId from the
NAU name if the NetId is present.
The reserved value '*ALL' indicates that the mode definition
applies to all partner LUs for the SNA node identified by
appcModeAdminLocLuName, and not just to a single partner LU."
::= { appcModeAdminEntry 2 }
appcModeAdminModeName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
MAX-ACCESS not-accessible
STATUS current
Allen, et. al. Standards Track [Page 45]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
DESCRIPTION
"Specifies the mode name. A mode defines the characteristics
for a group of sessions. The mode name can be blank (8
space characters). "
::= { appcModeAdminEntry 3 }
appcModeAdminCosName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the class of service (COS) name associated with
this mode. If the implementation does not support COS names,
a null string is returned."
::= { appcModeAdminEntry 4 }
appcModeAdminSessEndTpName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the name of the transaction program (TP) to be
invoked when a session using this mode is deactivated or ended.
If no such TP is defined, this object is a null string. When
the TP name consists entirely of displayable EBCDIC code
points, it is mapped directly to the equivalent ASCII display
string. However, registered TP names always have a non-
displayable EBCDIC code point (value less than or equal to
x'3F') as the first character, so they cannot be directly
mapped to an ASCII display string. These TP names are
converted to a display string that is equivalent to a
hexadecimal display of the EBCDIC code points. For example,
the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte
ASCII display string '06F1' (including the two single quotes).
"
::= { appcModeAdminEntry 5 }
appcModeAdminMaxSessLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the maximum value that the local LU is to use,
during CNOS processing, for the session limit. The local LU,
as a target LU, will negotiate a higher session limit it
Allen, et. al. Standards Track [Page 46]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
receives in the CNOS request down to this maximum value. The
local LU, as a source LU, will restrict the session limit it
sends in a CNOS request to a value less than or equal to this
maximum value."
::= { appcModeAdminEntry 6 }
appcModeAdminMinCwinLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the default minimum contention winner sessions
limit. Some implementations internally issue a
INITIALIZE_SESSION_LIMIT verb when a Mode is created. This
value is the parameter used for the CNOS processing of that
verb. This parameter is not used when issuing an explicit
INITIALIZE_SESSION_LIMIT verb. The equivalent object in
appcCnosCommandTable is used."
::= { appcModeAdminEntry 7 }
appcModeAdminMinClosLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the default minimum contention loser sessions limit.
Some implementations internally issue a
INITIALIZE_SESSION_LIMIT verb when a Mode is created. This
value is the parameter used for the CNOS processing of that
verb. This is the same as target minimum contention winner
sessions. This parameter is not used when issuing an explicit
INITIALIZE_SESSION_LIMIT verb. The equivalent object in
appcCnosCommandTable is used."
::= { appcModeAdminEntry 8 }
appcModeAdminConWinAutoActLmt OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the limit on the number of contention winner
sessions to be automatically activated when the minimum number
of contention winner sessions increases (as a result of CNOS
processing). The actual number of sessions activated is the
lesser of this value and the new minimum number of contention
winner sessions. "
Allen, et. al. Standards Track [Page 47]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
::= { appcModeAdminEntry 9 }
appcModeAdminRecvPacWinSz OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the size of the receive pacing window. This value is
used for negotiation during session activations (SNA BIND).
The meaning of this value when set to 0 depends on whether
adaptive pacing is supported:
adaptive pacing No limit on window size
fixed pacing No pacing is supported"
::= { appcModeAdminEntry 10 }
appcModeAdminSendPacWinSz OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the size of the send pacing window. This value is
used for negotiation during session activations (SNA BIND).
The meaning of this value when set to 0 depends on whether
adaptive pacing is supported:
adaptive pacing No limit on window size
fixed pacing No pacing is supported"
::= { appcModeAdminEntry 11 }
appcModeAdminPrefRecvRuSz OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the preferred receive RU (Request Unit) size of
normal-flow requests on the sessions. This value must be less
than or equal to the value specified in
appcModeAdminRecvRuSzUpBnd and greater than or equal to the
value specified in appcModeAdminRecvRuSzLoBnd.
The local LU specifies this value for the receive maximum RU
size in session activation (SNA BIND) requests and responses.
It will allow negotiation up to the appcModeAdminRecvRuSzUpBnd
value or down to the appcModeAdminRecvRuSzLoBnd value."
Allen, et. al. Standards Track [Page 48]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
::= { appcModeAdminEntry 12 }
appcModeAdminPrefSendRuSz OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the preferred send RU (Request Unit) size of normal-
flow requests on the sessions. This value must be less than or
equal to the value specified in appcModeAdminSendRuSzUpBnd and
greater than or equal to the value specified in
appcModeAdminSendRuSzLoBnd.
The local LU specifies this value for the send maximum RU
size in session activation (SNA BIND) requests and responses.
It will allow negotiation up to the appcModeAdminSendRuSzUpBnd
value or down to the appcModeAdminSendRuSzLoBnd value."
::= { appcModeAdminEntry 13 }
appcModeAdminRecvRuSzUpBnd OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the upper bound for the maximum receive RU
(Request Unit) size of normal-flow requests. This is used
for negotiation during session activations (SNA BIND). "
::= { appcModeAdminEntry 14 }
appcModeAdminSendRuSzUpBnd OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the upper bound for the maximum send RU (Request
Unit) size of normal-flow requests. This is used for
negotiation during session activations (SNA BIND). "
::= { appcModeAdminEntry 15 }
appcModeAdminRecvRuSzLoBnd OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the lower bound for the maximum receive RU (Request
Allen, et. al. Standards Track [Page 49]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
Unit) size of normal-flow requests. This is used for
negotiation during session activations (SNA BIND). "
::= { appcModeAdminEntry 16 }
appcModeAdminSendRuSzLoBnd OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the lower bound for the maximum send RU (Request
Unit) size of normal-flow requests. This is used for
negotiation during session activations (SNA BIND). "
::= { appcModeAdminEntry 17 }
appcModeAdminSingSessReinit OBJECT-TYPE
SYNTAX INTEGER {
notApplicable(1),
operatorControlled(2),
primaryOnly(3),
secondaryOnly(4),
primaryOrSecondary(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the responsibility for session reinitiation of a
single session with the partner LU (when the session goes
down). The local LU uses this parameter to specify the session
reinitiation responsibility in session activation (SNA BIND)
requests and responses.
notApplicable - specifies that this parameter has
no meaning since the value of
appcLuPairAdminParaSessSup is yes.
The field in the SNA BIND is
reserved (set to zero).
operatorControlled - specifies that neither LU will
automatically attempt to reinitiate
the session. The operator on either
side will manually reactivate the
session. A contention race (both
side reinitiating at the same time)
is won by the LU with the
lexicographically greater fully-
qualified LU name.
primaryOnly - specifies that the primary LU will
Allen, et. al. Standards Track [Page 50]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
automatically attempt to reinitiate
the session.
secondaryOnly - specifies that the secondary LU will
automatically attempt to reinitiate
the session.
primaryOrSecondary - specifies that either the primary or
the secondary may automatically
attempt to reinitiate the session.
A contention race is handled the
same way as with operatorControlled.
"
::= { appcModeAdminEntry 18 }
appcModeAdminCompression OBJECT-TYPE
SYNTAX INTEGER {
prohibited(1),
required(2),
negotiable(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether compression is supported. The local LU uses
this value for negotiation during session activation (SNA
BIND).
prohibited - specifies that no compression is to be used.
required - specifies that compression is required.
negotiable - specifies that the usage of compression
is to be negotiated between the LUs. The
level of compression is also negotiated."
::= { appcModeAdminEntry 19 }
appcModeAdminInBoundCompLevel OBJECT-TYPE
SYNTAX INTEGER {
none(1),
rle(2),
lz9(3),
lz10(4),
lz12(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the maximum level of compression supported for
inbound data. The local LU uses this value in conjunction with
appcModeAdminCompression for negotiation during session
Allen, et. al. Standards Track [Page 51]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
activation (SNA BIND).
none - specifies that no compression is to be used.
rle - specifies run-length encoding compression
in which a 1 or 2 byte sequence substitution is
used for each repeated run of the same character.
lz9 - specifies Lempel-Ziv-like compression in which
9 bit codes are used to substitute repeated
substrings in the data stream. These codes are
indices that refer to entries in a common
dictionary generated adaptively at both sender and
receiver as the data flows and compression occurs.
The larger of number bits used for the code, the
more storage space is required for the dictionary,
but the larger the compression ratio.
lz10 - specifies a 10 bit code Lempel-Ziv-like compression.
lz12 - specifies a 12 bit code Lempel-Ziv-like compression."
::= { appcModeAdminEntry 20 }
appcModeAdminOutBoundCompLevel OBJECT-TYPE
SYNTAX INTEGER {
none(1),
rle(2),
lz9(3),
lz10(4),
lz12(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the maximum level of compression supported for
outbound data. The local LU uses this value in conjunction
with appcModeAdminCompression for negotiation during session
activation (SNA BIND).
none - specifies that no compression is to be used.
rle - specifies run-length encoding compression
in which a 1 or 2 byte sequence substitution is
used for each repeated run of the same character.
lz9 - specifies Lempel-Ziv-like compression in which
9 bit codes are used to substitute repeated
substrings in the data stream. These codes are
indices that refer to entries in a common
dictionary generated adaptively at both sender and
receiver as the data flows and compression occurs.
The larger of number bits used for the code, the
more storage space is required for the dictionary,
Allen, et. al. Standards Track [Page 52]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
but the larger the compression ratio.
lz10 - specifies a 10 bit code Lempel-Ziv-like compression.
lz12 - specifies a 12 bit code Lempel-Ziv-like compression."
::= { appcModeAdminEntry 21 }
appcModeAdminCompRleBeforeLZ OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether run-length encoding is to be applied to the
data before applying Lempel-Ziv-like compression. The local LU
uses this value for negotiation during session activation (SNA
BIND). This parameter is only supported if LZ compression is
used."
::= { appcModeAdminEntry 22 }
appcModeAdminSyncLvl OBJECT-TYPE
SYNTAX INTEGER {
none(1),
noneConfirm(2),
noneConfirmSyncPoint(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the sync level support. This value is used for
negotiation during session activations (SNA BIND).
none - No sync level is supported.
noneConfirm - None and Confirm levels supported.
noneConfirmSyncPoint - None, Confirm, and Sync Point is
supported.
"
::= { appcModeAdminEntry 23 }
appcModeAdminCrypto OBJECT-TYPE
SYNTAX INTEGER {
notSupported(1),
mandatory(2),
selective(3)
}
Allen, et. al. Standards Track [Page 53]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether session-level cryptography is supported.
This value is used for negotiation during session activations
(SNA BIND).
notSupported - Specifies session-level cryptography
is not to be used.
mandatory - Specifies session-level cryptography
must be used.
selective - Specifies session-level cryptography
is required just on selected requests
flowing on the sessions."
::= { appcModeAdminEntry 24 }
-- *********************************************************************
-- APPC Mode Oper Table
-- Objects in this table contain current operational values, such
-- as state values or negotiated parameters, for session modes.
--
-- *********************************************************************
appcModeOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcModeOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Operational APPC Mode Information. Two entries are present in
the table when both LUs in a pair are local."
::= { appcLu 6 }
appcModeOperEntry OBJECT-TYPE
SYNTAX AppcModeOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry of APPC mode operational information table. This entry
does not augment the appcModeAdminEntry, but reflects an actual
operational mode for a given local LU - partner LU pair."
INDEX { appcModeOperLocLuName,
appcModeOperParLuName,
appcModeOperModeName }
::= { appcModeOperTable 1 }
Allen, et. al. Standards Track [Page 54]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
AppcModeOperEntry ::= SEQUENCE {
appcModeOperLocLuName DisplayString,
appcModeOperParLuName DisplayString,
appcModeOperModeName DisplayString,
appcModeOperCosName DisplayString,
appcModeOperSessEndTpName DisplayString,
appcModeOperSessLimit Integer32,
appcModeOperMaxSessLimit Integer32,
appcModeOperMinCwinLimit Integer32,
appcModeOperMinClosLimit Integer32,
appcModeOperConWinAutoActLmt Integer32,
appcModeOperRecvPacWinSz Integer32,
appcModeOperSendPacWinSz Integer32,
appcModeOperPrefRecvRuSz Integer32,
appcModeOperPrefSendRuSz Integer32,
appcModeOperRecvRuSzUpBnd Integer32,
appcModeOperSendRuSzUpBnd Integer32,
appcModeOperRecvRuSzLoBnd Integer32,
appcModeOperSendRuSzLoBnd Integer32,
appcModeOperSingSessReinit INTEGER,
appcModeOperCompression INTEGER,
appcModeOperInBoundCompLevel INTEGER,
appcModeOperOutBoundCompLevel INTEGER,
appcModeOperCompRleBeforeLZ INTEGER,
appcModeOperSyncLvl INTEGER,
appcModeOperCrypto INTEGER,
appcModeOperSyncLvlLastStart INTEGER,
appcModeOperCryptoLastStart INTEGER,
appcModeOperCNOSNeg INTEGER,
appcModeOperActCwin Gauge32,
appcModeOperActClos Gauge32,
appcModeOperPndCwin Gauge32,
appcModeOperPndClos Gauge32,
appcModeOperPtmCwin Gauge32,
appcModeOperPtmClos Gauge32,
appcModeOperDrainSelf INTEGER,
appcModeOperDrainPart INTEGER
}
appcModeOperLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNA name of the local LU. This field is from 1 to 17
characters in length, including a period (.) which separates
the NetId from the NAU name if the NetId is present.
Allen, et. al. Standards Track [Page 55]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
If this object has the same value as appcLluOperName,
then the two entries being indexed apply to the same
resource (specifically, to the same local LU)."
::= { appcModeOperEntry 1 }
appcModeOperParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNA name of the partner LU. This field is from 1 to 17
characters in length, including a period (.) which separates
the NetId from the NAU name if the NetId is present.
If this object has the same value as appcLuPairOperParLuName,
then the two entries being indexed apply to the same
resource (specifically, to the same partner LU)."
::= { appcModeOperEntry 2 }
appcModeOperModeName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the mode name. A mode defines the characteristics
for a group of sessions. The mode name can be blank (8
space characters). "
::= { appcModeOperEntry 3 }
appcModeOperCosName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the class of service (COS) name associated with
this mode. If the implementation does not support COS names,
a zero-length string is returned."
::= { appcModeOperEntry 4 }
appcModeOperSessEndTpName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Allen, et. al. Standards Track [Page 56]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
"Specifies the name of the transaction program (TP) to be
invoked when a session using this mode is deactivated or ended.
If the name is NULL, no transaction program is invoked. When
the TP name consists entirely of displayable EBCDIC code
points, it is mapped directly to the equivalent ASCII display
string. However, registered TP names always have a non-
displayable EBCDIC code point (value less than or equal to
x'3F') as the first character, so they cannot be directly
mapped to an ASCII display string. These TP names are
converted to a display string that is equivalent to a
hexadecimal display of the EBCDIC code points. For example,
the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte
ASCII display string '06F1' (including the two single quotes)."
::= { appcModeOperEntry 5 }
appcModeOperSessLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the current session limit of this mode as negotiated
through APPC CNOS (Change Number of Sessions) processing.
Identifies the total number of sessions that can be established
between the local and partner LU using this mode."
::= { appcModeOperEntry 6 }
appcModeOperMaxSessLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the maximum value that the local LU is to use,
during CNOS processing, for the session limit. The local LU,
as a target LU, will negotiate a higher session limit it
receives in the CNOS request down to this maximum value. The
local LU, as a source LU, will restrict the session limit it
sends in a CNOS request to a value less than or equal to this
maximum value."
::= { appcModeOperEntry 7 }
appcModeOperMinCwinLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Allen, et. al. Standards Track [Page 57]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
"Specifies the minimum contention winner sessions limit that
was negotiated via CNOS processing."
::= { appcModeOperEntry 8 }
appcModeOperMinClosLimit OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the minimum contention loser sessions limit that
was negotiated via CNOS processing. This is the same as
target minimum contention winner sessions."
::= { appcModeOperEntry 9 }
appcModeOperConWinAutoActLmt OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the limit on the number of contention winner sessions
to be automatically activated when the minimum number of
contention winner sessions increases (as a result of CNOS
processing). The actual number of sessions activated is the
lesser of this value and the new minimum number of contention
winner sessions. "
::= { appcModeOperEntry 10 }
appcModeOperRecvPacWinSz OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the size of the receive pacing window. This value is
used for negotiation during session activations (SNA BIND).
The meaning of this value when set to 0 depends on whether
adaptive pacing is supported:
adaptive pacing - No limit on window size
fixed pacing - No pacing is supported"
::= { appcModeOperEntry 11 }
appcModeOperSendPacWinSz OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
Allen, et. al. Standards Track [Page 58]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
STATUS current
DESCRIPTION
"Specifies the size of the send pacing window. This value is
used for negotiation during session activations (SNA BIND).
The meaning of this value when set to 0 depends on whether
adaptive pacing is supported:
adaptive pacing No limit on window size
fixed pacing No pacing is supported"
::= { appcModeOperEntry 12 }
appcModeOperPrefRecvRuSz OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the preferred receive RU (Request Unit) size of
normal-flow requests on the sessions. This value must be less
than or equal to the value specified in
appcModeOperRecvRuSzUpBnd and greater than or equal to the
value specified in appcModeOperRecvRuSzLoBnd.
The local LU specifies this value for the receive maximum RU
size in session activation (SNA BIND) requests and responses.
It will allow negotiation up to the appcModeOperRecvRuSzUpBnd
value or down to the appcModeOperRecvRuSzLoBnd value."
::= { appcModeOperEntry 13 }
appcModeOperPrefSendRuSz OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the preferred send RU (Request Unit) size of normal-
flow requests on the sessions. This value must be less than or
equal to the value specified in appcModeOperSendRuSzUpBnd and
greater than or equal to the value specified in
appcModeOperSendRuSzLoBnd.
The local LU specifies this value for the send maximum RU
size in session activation (SNA BIND) requests and responses.
It will allow negotiation up to the appcModeOperSendRuSzUpBnd
value or down to the appcModeOperSendRuSzLoBnd value."
::= { appcModeOperEntry 14 }
Allen, et. al. Standards Track [Page 59]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcModeOperRecvRuSzUpBnd OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the upper bound for the maximum receive RU
(Request Unit) size of normal-flow requests. This is used
for negotiation during session activations (SNA BIND). "
::= { appcModeOperEntry 15 }
appcModeOperSendRuSzUpBnd OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the upper bound for the maximum send RU (Request
Unit) size of normal-flow requests. This is used for
negotiation during session activations (SNA BIND). "
::= { appcModeOperEntry 16 }
appcModeOperRecvRuSzLoBnd OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the lower bound for the maximum receive RU
(Request Unit) size of normal-flow requests. This is used
for negotiation during session activations (SNA BIND). "
::= { appcModeOperEntry 17 }
appcModeOperSendRuSzLoBnd OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the lower bound for the maximum send RU
(Request Unit) size of normal-flow requests. This is used
for negotiation during session activations (SNA BIND). "
::= { appcModeOperEntry 18 }
appcModeOperSingSessReinit OBJECT-TYPE
SYNTAX INTEGER {
notApplicable(1),
operatorControlled(2),
Allen, et. al. Standards Track [Page 60]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
primaryOnly(3),
secondaryOnly(4),
primaryOrSecondary(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the responsibility for session reinitiation of a
single session with the partner LU (when the session goes
down). The local LU uses this parameter to specify the session
reinitiation responsibility in session activation (SNA BIND)
requests and responses.
notApplicable - specifies that this parameter has
no meaning since the value of
appcLuPairOperParaSessSup is yes.
The field in the SNA BIND is
reserved (set to zero).
operatorControlled - specifies that neither LU will
automatically attempt to reinitiate
the session. The operator on either
side will manually reactivate the
session. A contention race (both
side reinitiating at the same time)
is won by the LU with the
lexicographically greater fully-
qualified LU name.
primaryOnly - specifies that the primary LU will
automatically attempt to reinitiate
the session.
secondaryOnly - specifies that the secondary LU will
automatically attempt to reinitiate
the session.
primaryOrSecondary - specifies that either the primary or
the secondary may automatically
attempt to reinitiate the session.
A contention race is handled the
same way as with operatorControlled.
"
::= { appcModeOperEntry 19 }
appcModeOperCompression OBJECT-TYPE
SYNTAX INTEGER {
prohibited(1),
required(2),
negotiable(3)
}
MAX-ACCESS read-only
Allen, et. al. Standards Track [Page 61]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
STATUS current
DESCRIPTION
"Specifies whether compression is supported. The local LU uses
this value for negotiation during session activation (SNA
BIND).
prohibited - specifies that no compression is to be used.
required - specifies that compression is required.
negotiable - specifies that the usage of compression
is to be negotiated between the LUs. The
level of compression is also negotiated."
::= { appcModeOperEntry 20 }
appcModeOperInBoundCompLevel OBJECT-TYPE
SYNTAX INTEGER {
none(1),
rle(2),
lz9(3),
lz10(4),
lz12(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the maximum level of compression supported for
inbound data. The local LU uses this value in conjunction with
appcModeOperCompression for negotiation during session
activation (SNA BIND).
none - specifies that no compression is to be used.
rle - specifies run-length encoding compression
in which a 1 or 2 byte sequence substitution is
used for each repeated run of the same character.
lz9 - specifies Lempel-Ziv-like compression in which
9 bit codes are used to substitute repeated
substrings in the data stream. These codes are
indices that refer to entries in a common
dictionary generated adaptively at both sender and
receiver as the data flows and compression occurs.
The larger of number bits used for the code, the
more storage space is required for the dictionary,
but the larger the compression ratio.
lz10 - specifies a 10 bit code Lempel-Ziv-like compression.
lz12 - specifies a 12 bit code Lempel-Ziv-like compression."
::= { appcModeOperEntry 21 }
Allen, et. al. Standards Track [Page 62]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcModeOperOutBoundCompLevel OBJECT-TYPE
SYNTAX INTEGER {
none(1),
rle(2),
lz9(3),
lz10(4),
lz12(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the maximum level of compression supported for
outbound data. The local LU uses this value in conjunction
with appcModeOperCompression for negotiation during session
activation (SNA BIND).
none - specifies that no compression is to be used.
rle - specifies run-length encoding compression
in which a 1 or 2 byte sequence substitution is
used for each repeated run of the same character.
lz9 - specifies Lempel-Ziv-like compression in which
9 bit codes are used to substitute repeated
substrings in the data stream. These codes are
indices that refer to entries in a common
dictionary generated adaptively at both sender and
receiver as the data flows and compression occurs.
The larger of number bits used for the code, the
more storage space is required for the dictionary,
but the larger the compression ratio.
lz10 - specifies a 10 bit code Lempel-Ziv-like compression.
lz12 - specifies a 12 bit code Lempel-Ziv-like compression."
::= { appcModeOperEntry 22 }
appcModeOperCompRleBeforeLZ OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether run-length encoding is to be applied to the
data before applying Lempel-Ziv-like compression. The local LU
uses this value for negotiation during session activation (SNA
BIND). This parameter is only supported if LZ compression is
used."
Allen, et. al. Standards Track [Page 63]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
::= { appcModeOperEntry 23 }
appcModeOperSyncLvl OBJECT-TYPE
SYNTAX INTEGER {
none(1),
noneConfirm(2),
noneConfirmSyncPoint(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the sync level support for sessions involving this
LU pair and mode name.
none - No sync level is supported.
noneConfirm - None and Confirm level supported.
noneConfirmSyncPoint - None, Confirm and Sync Point is
supported.
"
::= { appcModeOperEntry 24 }
appcModeOperCrypto OBJECT-TYPE
SYNTAX INTEGER {
notSupported(1),
mandatory(2),
selective(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether session-level cryptography is supported for
sessions involving this LU pair and mode name.
notSupported - Specifies session-level cryptography
is not being used.
mandatory - Specifies session-level cryptography
in being used on all requests
flowing on the sessions.
selective - Specifies session-level cryptography
is required just on selected
requests flowing on the sessions."
::= { appcModeOperEntry 25 }
appcModeOperSyncLvlLastStart OBJECT-TYPE
SYNTAX INTEGER {
none(1),
Allen, et. al. Standards Track [Page 64]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
noneConfirm(2),
noneConfirmSyncPoint(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the sync level support. This value represents the
initial value proposed by the local LU the last time this
capability was negotiated, i.e., when the first session was
bound between the local LU and its partner.
none - No sync level is supported.
noneConfirm - None and Confirm level supported.
noneConfirmSyncPoint - None, Confirm and Sync Point is
supported.
"
::= { appcModeOperEntry 26 }
appcModeOperCryptoLastStart OBJECT-TYPE
SYNTAX INTEGER {
notSupported(1),
mandatory(2),
selective(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether session-level cryptography is supported.
This value represents the initial value proposed by the local
LU the last time this capability was negotiated, i.e., when
the first session was bound between the local LU and its
partner.
notSupported - Specifies session-level cryptography
is not to be used.
mandatory - Specifies session-level cryptography
must be used.
selective - Specifies session-level cryptography
is required just on selected
requests flowing on the sessions."
::= { appcModeOperEntry 27 }
appcModeOperCNOSNeg OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
Allen, et. al. Standards Track [Page 65]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether CNOS negotiation is in process. CNOS
negotiation is used to set or change the various session limits
for a mode."
::= { appcModeOperEntry 28 }
appcModeOperActCwin OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the number of active contention winner sessions."
::= { appcModeOperEntry 29 }
appcModeOperActClos OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the number of active contention loser sessions."
::= { appcModeOperEntry 30 }
appcModeOperPndCwin OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the number of contention winner sessions that are
pending activation."
::= { appcModeOperEntry 31 }
appcModeOperPndClos OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the number of contention loser sessions that are
pending activation."
::= { appcModeOperEntry 32 }
appcModeOperPtmCwin OBJECT-TYPE
Allen, et. al. Standards Track [Page 66]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the number of contention winner sessions that are
pending termination."
::= { appcModeOperEntry 33 }
appcModeOperPtmClos OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the number of contention loser sessions that are
pending termination."
::= { appcModeOperEntry 34 }
appcModeOperDrainSelf OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether the local LU is draining its conversations
for this mode. When a mode session limit is reset (via a CNOS
RESET_SESSION_LIMIT request), the local LU could be set to
process all queued conversations before deactivating all of the
sessions (using the SNA Bracket Initiation Stopped or BIS
protocol). "
::= { appcModeOperEntry 35 }
appcModeOperDrainPart OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether the partner LU is draining its conversations
for this mode. When a mode session limit is reset (via a CNOS
RESET_SESSION_LIMIT request), the partner LU could be set to
process all queued conversations before deactivating all of the
Allen, et. al. Standards Track [Page 67]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
sessions (using the SNA Bracket Initiation Stop or BIS
protocol). "
::= { appcModeOperEntry 36 }
-- *********************************************************************
-- APPC TP Admin Table
-- Objects in this table contain default or expected configuration
-- values for remotely attachable transaction programs.
-- *********************************************************************
appcTpAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcTpAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"APPC Local TP Table"
::= { appcTp 1 }
appcTpAdminEntry OBJECT-TYPE
SYNTAX AppcTpAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry of APPC Local TP Information Table."
INDEX { appcTpAdminLocLuName,
appcTpAdminTpName }
::= { appcTpAdminTable 1 }
AppcTpAdminEntry ::= SEQUENCE {
appcTpAdminLocLuName DisplayString,
appcTpAdminTpName DisplayString,
appcTpAdminFileSpec DisplayString,
appcTpAdminStartParm DisplayString,
appcTpAdminTpOperation INTEGER,
appcTpAdminInAttachTimeout Integer32,
appcTpAdminRcvAllocTimeout Integer32,
appcTpAdminSyncLvl INTEGER,
appcTpAdminInstLmt Integer32,
appcTpAdminStatus INTEGER,
appcTpAdminLongRun INTEGER,
appcTpAdminConvType INTEGER,
appcTpAdminConvDuplex INTEGER,
appcTpAdminConvSecReq INTEGER,
appcTpAdminVerPip INTEGER,
appcTpAdminPipSubNum Integer32
Allen, et. al. Standards Track [Page 68]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
}
appcTpAdminLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNA name of the local LU to which this TP definition
applies. This field is from 1 to 17 characters in length,
including a period (.) which separates the NetId from the NAU
name if the NetId is present.
The reserved value '*ALL' indicates that the TP definition
applies to all local LUs, and not just to a single local LU."
::= { appcTpAdminEntry 1 }
appcTpAdminTpName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..64))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The local transaction program name. This name is sent on an
ATTACH remote allocation request.
When the TP name consists entirely of displayable EBCDIC
code points, it is mapped directly to the equivalent ASCII
display string. However, registered TP names always have a
non-displayable EBCDIC code point (value less than or equal to
x'3F') as the first character, so they cannot be directly
mapped to an ASCII display string. These TP names are
converted to a display string that is equivalent to a
hexadecimal display of the EBCDIC code points. For example,
the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte
ASCII display string '06F1' (including the two single quotes)."
::= { appcTpAdminEntry 2 }
appcTpAdminFileSpec OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..80))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local file specification of the transaction program.
May be a zero-length string if not applicable."
::= { appcTpAdminEntry 3 }
Allen, et. al. Standards Track [Page 69]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcTpAdminStartParm OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A parameter string passed to the transaction program when it
is started. May be a zero-length string if not supported. "
::= { appcTpAdminEntry 4 }
appcTpAdminTpOperation OBJECT-TYPE
SYNTAX INTEGER {
other(1),
queuedOperatorStarted(2),
queuedOperatorPreloaded(3),
queuedAmStarted(4),
nonqueuedAmStarted(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies how the program will be started.
other - Specifies that the program operation is none of
the methods specified. It may be a
product-specific method.
queuedOperatorStarted - Specifies that one version of the
program will be run at a time. If an incoming
attach arrives and the program has not been started
yet, APPC will issue a message to the operator to
start the specified program. Subsequent attaches
that arrive while the program is active will be
queued.
queuedOperatorPreloaded - Specifies that one version of the
program will be run at a time. If an incoming
attach arrives and the program has not been started
yet, the Attach will be rejected. The APPC attach
manager determines that a TP has started upon
reception of an APPC RECEIVE_ALLOCATE verb, or a
CPI-C Accept_Conversation (CMACCP) or
Specify_Local_TP_Name (CMSLTP) call. No message is
sent to the operator. Subsequent attaches that
arrive while the program is active are queued.
queuedAmStarted - Specifies that one version of the
program will be run at a time and will be started
by the APPC attach manager. Subsequent attaches
Allen, et. al. Standards Track [Page 70]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
that arrive while the program is active will be
queued.
nonqueuedAmStarted - Specifies that multiple copies of the
program will be run at a time and will be started
by the APPC attach manager."
::= { appcTpAdminEntry 5 }
appcTpAdminInAttachTimeout OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the number of seconds incoming attaches
will be queued waiting for an APPC program to issue a
RECEIVE_ALLOCATE verb or for a CPI-C program to issue an
Accept_Conversation (CMACCP) call. This parameter is
meaningful only when appcTpAdminTpOperation has one of the
following values:
queuedOperatorStarted
queuedOperatorPreloaded
queuedAmStarted
A value of zero indicates that there is no timeout."
::= { appcTpAdminEntry 6 }
appcTpAdminRcvAllocTimeout OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object specifies the number of seconds an APPC program's
RECEIVE_ALLOCATE verb or a CPI-C program's Accept_Conversation
(CMACCP) call will wait for an incoming attach to arrive.
A value of zero indicates that there is no timeout."
::= { appcTpAdminEntry 7 }
appcTpAdminSyncLvl OBJECT-TYPE
SYNTAX INTEGER {
none(1),
confirm(2),
noneAndConfirm(3),
syncpoint(4),
noneAndSyncpoint(5),
Allen, et. al. Standards Track [Page 71]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
confirmAndSyncpoint(6),
all(7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the synchronization level or levels that the
transaction program supports. The levels are defined as
follows:
none - allocation requests indicating a
synchronization level of none are allowed to
start the program.
confirm - allocation requests indicating a
synchronization level of confirm are allowed
to start the program.
syncpoint - allocation requests indicating a
synchronization level of sync point are
allowed to start the program."
::= { appcTpAdminEntry 8 }
appcTpAdminInstLmt OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of concurrent instances of this transaction
program that will be supported for a local LU. A value of
zero indicates that there is no limit."
::= { appcTpAdminEntry 9 }
appcTpAdminStatus OBJECT-TYPE
SYNTAX INTEGER {
enabled(1),
tempDisabled(2),
permDisabled(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the status of the TP relative to starting execution
when the local LU receives an allocation (ATTACH) request
naming this program.
enabled - the local LU can start the program.
tempDisabled - the local LU cannot start the
Allen, et. al. Standards Track [Page 72]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
program. The local LU rejects the
request with an indication that the
TP is not available but retry is
possible.
permDisabled - the local LU cannot start the
program. The local LU rejects the
request with an indication that the
TP is not available and retry is
not possible."
::= { appcTpAdminEntry 10 }
appcTpAdminLongRun OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether this is a long-running transaction program
(i.e., one that stays around even after the conversation goes
away)."
::= { appcTpAdminEntry 11 }
appcTpAdminConvType OBJECT-TYPE
SYNTAX INTEGER {
basic(1),
mapped(2),
basicOrMapped(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the conversation type (basic or mapped) that will be
used by the TP. This value is verified upon receipt of an
incoming attach. The acceptable values are:
basic - Indicates that this transaction program
supports basic conversations.
mapped - Indicates that this transaction program
supports mapped conversations.
basicOrMapped - Indicates that this transaction program
supports both basic and mapped
conversations."
Allen, et. al. Standards Track [Page 73]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
::= { appcTpAdminEntry 12 }
appcTpAdminConvDuplex OBJECT-TYPE
SYNTAX INTEGER {
half(1),
full(2),
halfOrFull(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the conversation duplex type (half or full) that
will be used by the TP. This value is verified upon receipt of
an incoming attach. The acceptable values are:
half - Indicates that this transaction program
supports half duplex conversations.
full - Indicates that this transaction program
supports full duplex conversations.
halfOrFull - Indicates that this transaction program
supports either half or full duplex
conversations."
::= { appcTpAdminEntry 13 }
appcTpAdminConvSecReq OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether conversation-level security information is
required on incoming attaches designating this TP name.
Conversation-level security verification is always performed on
those requests that include security information.
yes - Indicates that conversation-level security
information is required. ATTACHs designating the
transaction program must carry a user_id and
either a password or an already verified
indicator.
no - Indicates that no security information is
required. ATTACHs designating the transaction
Allen, et. al. Standards Track [Page 74]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
program can omit or include security information."
::= { appcTpAdminEntry 14 }
appcTpAdminVerPip OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether the number of PIP (Program Initialization
Parameters) subfields should be verified against the number
expected (appcTpAdminPipSubNum)."
::= { appcTpAdminEntry 15 }
appcTpAdminPipSubNum OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the number of PIP subfields expected by the TP."
::= { appcTpAdminEntry 16 }
-- *********************************************************************
-- APPC Active Session Table
-- ---------------------------------------------------------------------
-- This table contains information about active APPC sessions.
-- *********************************************************************
appcActSessTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcActSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of active APPC sessions. Two entries are present in the
table when both session partners are local."
::= { appcSession 1 }
appcActSessEntry OBJECT-TYPE
SYNTAX AppcActSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Allen, et. al. Standards Track [Page 75]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
"Entry of APPC Session Information Table. Indexed by LU pair
and integer-valued session index."
INDEX { appcActSessLocLuName,
appcActSessParLuName,
appcActSessIndex }
::= { appcActSessTable 1 }
AppcActSessEntry ::= SEQUENCE {
appcActSessLocLuName DisplayString,
appcActSessParLuName DisplayString,
appcActSessIndex Integer32,
appcActSessPcidCpName DisplayString,
appcActSessPcid OCTET STRING,
appcActSessPluIndicator INTEGER,
appcActSessModeName DisplayString,
appcActSessCosName DisplayString,
appcActSessTransPriority INTEGER,
appcActSessEnhanceSecSup INTEGER,
appcActSessSendPacingType INTEGER,
appcActSessSendRpc Gauge32,
appcActSessSendNxWndwSize Gauge32,
appcActSessRecvPacingType INTEGER,
appcActSessRecvRpc Gauge32,
appcActSessRecvNxWndwSize Gauge32,
appcActSessRscv OCTET STRING,
appcActSessInUse INTEGER,
appcActSessMaxSndRuSize INTEGER,
appcActSessMaxRcvRuSize INTEGER,
appcActSessSndPacingSize INTEGER,
appcActSessRcvPacingSize INTEGER,
appcActSessOperState INTEGER,
appcActSessUpTime TimeTicks,
appcActSessRtpNceId OCTET STRING,
appcActSessRtpTcid OCTET STRING,
appcActSessLinkIndex InstancePointer
}
appcActSessLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the name of the local LU for the session. This
field is from 1 to 17 characters in length, including a period
(.) which separates the NetId from the NAU name if the NetId is
Allen, et. al. Standards Track [Page 76]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
present.
If this object has the same value as appcLluOperName, then the
two entries being indexed apply to the same resource
(specifically, to the same local LU)."
::= { appcActSessEntry 1 }
appcActSessParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the name of the partner LU for the session. This
field is from 1 to 17 characters in length, including a period
(.) which separates the NetId from the NAU name if the NetId is
present.
If this object has the same value as appcLuPairOperParLuName,
then the two entries being indexed apply to the same resource
(specifically, to the same partner LU)."
::= { appcActSessEntry 2 }
appcActSessIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This value identifies the index of the session, which is
unique for this LU pair. It is recommended that an Agent not
reuse the index of a deactivated session for a significant
period of time (e.g., one week)."
::= { appcActSessEntry 3 }
appcActSessPcidCpName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0 | 3..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network-qualified CP name of the node at which the session
and PCID originated. For APPN and LEN nodes, this is either CP
name of the APPN node at which the origin LU is located or the
CP name of the NN serving the LEN node at which the origin LU
is located. This field is from 3 to 17 characters in length,
including a period (.) which separates the NetId from the NAU
name. A null string indicates that the value is unknown."
Allen, et. al. Standards Track [Page 77]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
::= { appcActSessEntry 4 }
appcActSessPcid OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0|8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The procedure correlation identifier (PCID) of a session. It
is an 8-octet value assigned by the control point providing
session services for the primary LU. A null string indicates
that the value is unknown."
::= { appcActSessEntry 5 }
appcActSessPluIndicator OBJECT-TYPE
SYNTAX INTEGER {
localLuIsPlu(1),
partnerLuIsPlu(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates which LU is the PLU for this session. For
independent LUs, the PLU (primary LU) is the one that initiated
the session (sent BIND), while the SLU (secondary LU) is the
one that accepted the session initiation (received BIND).
The 'local' LU is the one identified by appcLluOperName.
The 'partner' LU is the one identified by
appcLuPairOperParLuName."
::= { appcActSessEntry 6 }
appcActSessModeName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The mode name used for this session."
::= { appcActSessEntry 7 }
appcActSessCosName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
Allen, et. al. Standards Track [Page 78]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
"The Class of Service (COS) name used for this session.
A null string indicates that the value is unknown."
::= { appcActSessEntry 8 }
appcActSessTransPriority OBJECT-TYPE
SYNTAX INTEGER {
unknown(1),
low(2),
medium(3),
high(4),
network(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transmission priority of this session.
1 = unknown priority
2 = low priority
3 = medium priority
4 = high priority
5 = network priority
"
::= { appcActSessEntry 9 }
appcActSessEnhanceSecSup OBJECT-TYPE
SYNTAX INTEGER {
none(1),
level1(2),
level2(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Enhanced security supported. Indicates the level of enhanced
security support:
1 = none
2 = level 1
3 = level 2
"
::= { appcActSessEntry 10 }
appcActSessSendPacingType OBJECT-TYPE
SYNTAX INTEGER {
none(1),
Allen, et. al. Standards Track [Page 79]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
fixed(2),
adaptive(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of pacing being used for sending data."
::= { appcActSessEntry 11 }
appcActSessSendRpc OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The send residual pace count. This represents the number of
MUs that can still be sent in the current session window."
::= { appcActSessEntry 12 }
appcActSessSendNxWndwSize OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The size of the next window which will be used to send data."
::= { appcActSessEntry 13 }
appcActSessRecvPacingType OBJECT-TYPE
SYNTAX INTEGER {
none(1),
fixed(2),
adaptive(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of pacing being used for receiving data."
::= { appcActSessEntry 14 }
appcActSessRecvRpc OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The receive residual pace count. This represents the number
Allen, et. al. Standards Track [Page 80]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
of MUs that can still be received in the current session
window."
::= { appcActSessEntry 15 }
appcActSessRecvNxWndwSize OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The size of the next window which will be used to receive
data."
::= { appcActSessEntry 16 }
appcActSessRscv OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The route selection control vector (RSCV CV2B) used for this
session. It is present for APPN-level implementations.
LEN-level implementations will return a null string. The
internal format of this vector is described in SNA Formats.
This object contains an uninterpreted copy of the control
vector (including the length and key fields)."
::= { appcActSessEntry 17 }
appcActSessInUse OBJECT-TYPE
SYNTAX INTEGER {
no(1),
yes(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether the session is currently in use (i.e., in
bracket with a conversation)."
::= { appcActSessEntry 18 }
appcActSessMaxSndRuSize OBJECT-TYPE
SYNTAX INTEGER (1..8192)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum RU size used on this session for sending RUs."
Allen, et. al. Standards Track [Page 81]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
::= { appcActSessEntry 19 }
appcActSessMaxRcvRuSize OBJECT-TYPE
SYNTAX INTEGER (1..8192)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum RU size used on this session for receiving RUs."
::= { appcActSessEntry 20 }
appcActSessSndPacingSize OBJECT-TYPE
SYNTAX INTEGER (1..63)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The size of the send pacing window on this session."
::= { appcActSessEntry 21 }
appcActSessRcvPacingSize OBJECT-TYPE
SYNTAX INTEGER (1..63)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The size of the receive pacing window on this session."
::= { appcActSessEntry 22 }
appcActSessOperState OBJECT-TYPE
SYNTAX INTEGER {
unbound (1),
pendingBind (2),
bound (3),
pendingUnbind (4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value indicates the current operational state of the
session.
'unbound (1)' - session has been unbound;
in this state it will be removed from the
session table by the Agent.
'pendingBind (2)' - this state has different
meanings for dependent and independent LUs;
Allen, et. al. Standards Track [Page 82]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
for dependent LU - waiting for BIND from
the host, for independent LU - waiting for
BIND response. When a session enters this
state, the corresponding entry in the
session table is created by the Agent.
'bound (3)' - session has been successfully bound.
'pendingUnbind (4)' - session enters this state
when an UNBIND is sent and before the
rsp(UNBIND) is received.
Session deactivation:
If a session is in the operational state
'bound (3)' then setting the value of this
object to 'unbound (1)' will initiate the
session shutdown.
If a session is in the operational state
'pendingBind (2)' then setting the value of this
object to 'unbound (1)' will initiate the session
shutdown.
If a session is in the operational state
'pendingUnbind (4)' for an abnormally long period
of time (e.g., three minutes) then setting the value
of this object to 'unbound (1)' will change the
session operational state to 'unbound (1)'. "
::= { appcActSessEntry 23 }
appcActSessUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length of time the session has been active, measured in
hundredths of a second."
::= { appcActSessEntry 24 }
appcActSessRtpNceId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local HPR Network Connection Endpoint of the session."
Allen, et. al. Standards Track [Page 83]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
::= { appcActSessEntry 25 }
appcActSessRtpTcid OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0|8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The local RTP connection TCID of the session."
::= { appcActSessEntry 26 }
appcActSessLinkIndex OBJECT-TYPE
SYNTAX InstancePointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This value identifies the link over which the session passes.
This value points to the row in the table containing
information on the link instance. (e.g., the sdlcLSAdminTable
of the SNA DLC MIB module). This object may be NULL if the
link is not specified or if a link is not applicable (as for
APPN-level nodes)."
::= { appcActSessEntry 27 }
-- ***************************************************************
-- The following table contains session statistics for APPC sessions.
-- ***************************************************************
appcSessStatsTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcSessStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table contains dynamic statistical information relating
to active APPC sessions. The entries in this table cannot be
created by a Management Station. Two entries are present in
the table when both session partners are local. This table is
populated only when the value of appcCntrlOperStat is
'active'."
::= { appcSession 2 }
appcSessStatsEntry OBJECT-TYPE
SYNTAX AppcSessStatsEntry
MAX-ACCESS not-accessible
STATUS current
Allen, et. al. Standards Track [Page 84]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
DESCRIPTION
"Contains statistics information for an APPC session. Each
entry is created by the Agent. Objects in this table have
read-only access. Each session from appcActSessTable has one
entry in this table."
INDEX { appcSessStatsLocLuName,
appcSessStatsParLuName,
appcSessStatsSessIndex }
::= { appcSessStatsTable 1 }
AppcSessStatsEntry ::= SEQUENCE {
appcSessStatsLocLuName DisplayString,
appcSessStatsParLuName DisplayString,
appcSessStatsSessIndex Integer32,
appcSessStatsSentFmdBytes Counter32,
appcSessStatsSentNonFmdBytes Counter32,
appcSessStatsRcvdFmdBytes Counter32,
appcSessStatsRcvdNonFmdBytes Counter32,
appcSessStatsSentFmdRus Counter32,
appcSessStatsSentNonFmdRus Counter32,
appcSessStatsRcvdFmdRus Counter32,
appcSessStatsRcvdNonFmdRus Counter32,
appcSessStatsCtrUpTime TimeTicks
}
appcSessStatsLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the name of the local LU for the session. This
field is from 1 to 17 characters in length, including a period
(.) which separates the NetId from the NAU name if the NetId is
present.
If this object has the same value as appcLluOperName, then the
two entries being indexed apply to the same resource
(specifically, to the same local LU)."
::= { appcSessStatsEntry 1 }
appcSessStatsParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Allen, et. al. Standards Track [Page 85]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
"Specifies the name of the partner LU for the session. This
field is from 1 to 17 characters in length, including a period
(.) which separates the NetId from the NAU name if the NetId is
present.
If this object has the same value as appcLuPairOperParLuName,
then the two entries being indexed apply to the same resource
(specifically, to the same partner LU)."
::= { appcSessStatsEntry 2 }
appcSessStatsSessIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This value identifies the index of the session, which is
unique for this LU pair. It is recommended that an Agent not
reuse the index of a deactivated session for a significant
period of time (e.g., one week).
If this object has the same value as appcActSessIndex for the
same LU pair, then the two entries being indexed apply to the
same resource (specifically, to the same session)."
::= { appcSessStatsEntry 3 }
appcSessStatsSentFmdBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of function management data (FMD) bytes sent by the
local LU."
::= { appcSessStatsEntry 4 }
appcSessStatsSentNonFmdBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of non-function management data (non-FMD) bytes
sent by the local LU."
::= { appcSessStatsEntry 5 }
appcSessStatsRcvdFmdBytes OBJECT-TYPE
Allen, et. al. Standards Track [Page 86]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of function management data (FMD) bytes received by
the local LU."
::= { appcSessStatsEntry 6 }
appcSessStatsRcvdNonFmdBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of non-function management data (non-FMD) bytes
received by the local LU."
::= { appcSessStatsEntry 7 }
appcSessStatsSentFmdRus OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of function management data (FMD) RUs sent by the
local LU."
::= { appcSessStatsEntry 8 }
appcSessStatsSentNonFmdRus OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of non-function management data (non-FMD) RUs sent
by the local LU."
::= { appcSessStatsEntry 9 }
appcSessStatsRcvdFmdRus OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of function management data (FMD) RUs received by
the local LU."
::= { appcSessStatsEntry 10 }
Allen, et. al. Standards Track [Page 87]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcSessStatsRcvdNonFmdRus OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of non-function management data (non-FMD) RUs
received by the local LU."
::= { appcSessStatsEntry 11 }
appcSessStatsCtrUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length of time the counters for this session have been
active, measured in hundredths of a second."
::= { appcSessStatsEntry 12 }
-- *********************************************************************
-- APPC Historical Session Table
-- ---------------------------------------------------------------------
-- This table contains historical information about APPC sessions that
-- terminated abnormally. It is an implementation choice how long to
-- retain information on a given session.
-- *********************************************************************
appcHistSessTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcHistSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of historical information about APPC sessions that
terminated abnormally. Two entries may be present in the table
when both session partners are local. It is an implementation
choice how long to retain information about a given session."
::= { appcSession 3 }
appcHistSessEntry OBJECT-TYPE
SYNTAX AppcHistSessEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry of APPC Session History Table. This table is indexed by
an integer which is continuously incremented until it
eventually wraps."
Allen, et. al. Standards Track [Page 88]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
INDEX
{ appcHistSessIndex }
::= { appcHistSessTable 1 }
AppcHistSessEntry ::= SEQUENCE {
appcHistSessIndex INTEGER,
appcHistSessTime DateAndTime,
appcHistSessType INTEGER,
appcHistSessLocLuName DisplayString,
appcHistSessParLuName DisplayString,
appcHistSessModeName DisplayString,
appcHistSessUnbindType OCTET STRING,
appcHistSessSenseData SnaSenseData,
appcHistSessComponentId DisplayString,
appcHistSessDetectModule DisplayString
}
appcHistSessIndex OBJECT-TYPE
SYNTAX INTEGER (0..2147483647)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table index. The value of the index begins at zero
and is incremented up to a maximum value of 2**31-1
(2,147,483,647) before wrapping."
::= { appcHistSessEntry 1 }
appcHistSessTime OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time at which the session was either terminated or
failed to be established."
::= { appcHistSessEntry 2 }
appcHistSessType OBJECT-TYPE
SYNTAX INTEGER {
recvNegBindRsp(1),
sendNegBindRsp(2),
sessActRejected(3),
unbindSent(4),
unbindReceived(5)
}
Allen, et. al. Standards Track [Page 89]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the type of event that caused the entry to be made:
recvNegBindRsp - Received a negative bind response from
the partner LU.
sendNegBindRsp - Sent a negative bind response to the
partner LU.
sessActRejected - Session activation rejected by the
partner LU.
unbindSent - Unbind sent to the partner LU.
unbindReceived - Unbind received from the partner LU.
These event types correspond to the five SNA/MS Alerts
LU62001 through LU62005, documented in the SNA Management
Services Reference."
::= { appcHistSessEntry 3 }
appcHistSessLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network-qualified local LU name. This field is from 3 to
17 characters in length, including a period (.) which separates
the NetId from the NAU name if the NetId is present."
::= { appcHistSessEntry 4 }
appcHistSessParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (3..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network-qualified partner LU name. This field is from 3
to 17 characters in length, including a period (.) which
separates the NetId from the NAU name if the NetId is present."
::= { appcHistSessEntry 5 }
appcHistSessModeName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The mode name of the session."
Allen, et. al. Standards Track [Page 90]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
::= { appcHistSessEntry 6 }
appcHistSessUnbindType OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The type of unbind which terminated the session. This
value is consists of one (1) octet; and its meaning
is defined in SNA Formats."
::= { appcHistSessEntry 7 }
appcHistSessSenseData OBJECT-TYPE
SYNTAX SnaSenseData
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sense data associated with the termination of the
session, taken from the negative BIND response or UNBIND
request."
::= { appcHistSessEntry 8 }
appcHistSessComponentId OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The implementation-specific name of the component which
detected the problem."
::= { appcHistSessEntry 9 }
appcHistSessDetectModule OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The implementation-specific name of the module which
detected the problem."
::= { appcHistSessEntry 10 }
-- *********************************************************************
-- APPC Session RTP Connection Table
-- ---------------------------------------------------------------------
Allen, et. al. Standards Track [Page 91]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
-- This table contains information on APPC sessions that are being
-- transported on RTP connections by High Performance Routing (HPR).
-- *********************************************************************
appcSessRtpTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcSessRtpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A table indicating how many APPC sessions terminating in this
node are transported by each RTP connection."
::= { appcSession 4 }
appcSessRtpEntry OBJECT-TYPE
SYNTAX AppcSessRtpEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry of APPC session RTP table."
INDEX { appcSessRtpNceId,
appcSessRtpTcid }
::= { appcSessRtpTable 1 }
AppcSessRtpEntry ::= SEQUENCE {
appcSessRtpNceId OCTET STRING,
appcSessRtpTcid OCTET STRING,
appcSessRtpSessions Gauge32
}
appcSessRtpNceId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (1..8))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The local Network Connection Endpoint of the RTP connection."
::= { appcSessRtpEntry 1 }
appcSessRtpTcid OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (8))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The local TCID of the RTP connection."
::= { appcSessRtpEntry 2 }
Allen, et. al. Standards Track [Page 92]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcSessRtpSessions OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of APPC sessions terminating in this node
that are using this RTP connection."
::= { appcSessRtpEntry 3 }
-- *********************************************************************
-- APPC Active Conversation Table
-- This table contains information about active APPC conversations.
-- *********************************************************************
appcActiveConvTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcActiveConvEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of information about active APPC Conversations. In this
context 'active' means that a conversation is currently
associated with a particular session. Two entries are present
in the table when both LUs for the session are local."
::= { appcConversation 1 }
appcActiveConvEntry OBJECT-TYPE
SYNTAX AppcActiveConvEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry representing one active APPC Conversation."
INDEX { appcActiveConvLocLuName,
appcActiveConvParLuName,
appcActiveConvSessIndex }
::= { appcActiveConvTable 1}
AppcActiveConvEntry ::= SEQUENCE {
appcActiveConvLocLuName DisplayString,
appcActiveConvParLuName DisplayString,
appcActiveConvSessIndex Integer32,
appcActiveConvId OCTET STRING,
appcActiveConvState INTEGER,
appcActiveConvType INTEGER,
Allen, et. al. Standards Track [Page 93]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcActiveConvCorrelator OCTET STRING,
appcActiveConvSyncLvl INTEGER,
appcActiveConvSource INTEGER,
appcActiveConvDuplex INTEGER,
appcActiveConvUpTime TimeTicks,
appcActiveConvSendBytes Counter32,
appcActiveConvRcvBytes Counter32,
appcActiveConvUserid DisplayString,
appcActiveConvPcidNauName DisplayString,
appcActiveConvPcid OCTET STRING,
appcActiveConvModeName DisplayString,
appcActiveConvLuwIdName DisplayString,
appcActiveConvLuwIdInstance OCTET STRING,
appcActiveConvLuwIdSequence OCTET STRING,
appcActiveConvTpName DisplayString
}
appcActiveConvLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNA name of the local LU for the conversation. This field
is from 1 to 17 characters in length, including a period (.)
which separates the NetId from the NAU name if the NetId is
present.
If this object has the same value as appcLluOperName,
then the two entries being indexed apply to the same
resource (specifically, to the same local LU)."
::= { appcActiveConvEntry 1 }
appcActiveConvParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNA name of the partner LU for the conversation. This
field is from 1 to 17 characters in length, including a period
(.) which separates the NetId from the NAU name if the NetId is
present.
If this object has the same value as appcLuPairOperParLuName,
then the two entries being indexed apply to the same
resource (specifically, to the same partner LU)."
::= { appcActiveConvEntry 2 }
Allen, et. al. Standards Track [Page 94]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcActiveConvSessIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of entry in appcActSessTable that is associated with
this conversation. If this object has the same value as
appcActSessIndex for the same LU pair, then the two entries
being indexed apply to the same resource (specifically, to the
same session)."
::= { appcActiveConvEntry 3 }
appcActiveConvId OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (4))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The 4-byte ID of the conversation."
::= { appcActiveConvEntry 4 }
appcActiveConvState OBJECT-TYPE
SYNTAX INTEGER {
reset(1),
send(2),
receive(3),
confirm(4),
confirmSend(5),
confirmDealloc(6),
pendingDeallocate(7),
pendingPost(8),
sendReceive(9),
sendOnly(10),
receiveOnly(11),
deferReceive(12),
deferDeallocate(13),
syncpoint(14),
syncpointSend(15),
syncpointDeallocate(16),
backoutRequired(17)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the state of the conversation at the instant when
the information was retrieved. The values are:
Allen, et. al. Standards Track [Page 95]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
reset
The conversation is reset (i.e., deallocated).
send
The conversation can send data. This value also
is returned if the conversation is in
Send-Pending state.
receive
The conversation can receive data.
confirm
The conversation has received a confirm
indicator. It can issue an [MC_]CONFIRMED or
[MC_]SEND_ERROR verb to change state. It will
continue in Receive state if an [MC_]CONFIRMED
verb is issued.
confirmSend
The conversation is in Confirm state and changes
to Send state when an [MC_]CONFIRMED verb is
issued.
confirmDealloc
The conversation is in Confirm state and becomes
inactive when an [MC_]CONFIRMED verb is issued.
pendingDeallocate
The conversation is in Pending-Deallocate state
while it waits for (MC_)DEALLOCATE TYPE
(sync_level) to complete.
pendingPost
The conversation is in Pending-Post state while
it waits for the [MC_]RECEIVE_AND_POST verb to
complete its receive function.
sendReceive
The full-duplex conversation can send or receive
data.
sendOnly
The full-duplex conversation can send data, but
it does not have permission to receive data,
because the partner TP has already deallocated
its side of the conversation.
receiveOnly
The full-duplex conversation can receive data,
but it does not have permission to send data,
because it has already deallocated its side of
the conversation.
deferReceive
Waiting for a successful SYNCPT verb operation to
go into the receive state.
deferDeallocate
Waiting for a successful SYNCPT verb operation to
go into the reset state.
Allen, et. al. Standards Track [Page 96]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
syncpoint
Need to response to a SYNCPT verb issued. After
successful operation, the next state will be
receive.
syncpointSend
Need to response to a SYNCPT verb issued. After
successful operation, the next state will be
send.
syncpointDeallocate
Need to response to a SYNCPT verb issued. After
successful operation, the next state will be
reset.
backoutRequired
TP must execute a BACKOUT verb to backout the
transaction."
::= { appcActiveConvEntry 5 }
appcActiveConvType OBJECT-TYPE
SYNTAX INTEGER {
basic(1),
mapped(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the type of conversation. The values are:
basic
Indicates that this conversation supports
basic verbs.
mapped
Indicates that this conversation supports
mapped verbs."
::= { appcActiveConvEntry 6 }
appcActiveConvCorrelator OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This is an 8-byte identifier that the source LU assigns to the
conversation; the source LU is the one that sent the allocation
request. The conversation correlator is included on the
allocation request. The conversation correlator uniquely
Allen, et. al. Standards Track [Page 97]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
identifies a conversation, from among all conversations,
between the local and partner LUs. It may be used, for
example, during problem determination associated with a
conversation. A length of 0 indicates that no conversation
correlator is defined."
::= { appcActiveConvEntry 7 }
appcActiveConvSyncLvl OBJECT-TYPE
SYNTAX INTEGER {
none(1),
confirm(2),
syncpt(3)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the highest sync level support for the conversation.
The values are:
none
Indicates that no sync-level processing can be
performed on this conversation. The
transaction program does not issue verbs or
recognize any returned parameters
relating to any sync-level function.
confirm
Indicates that confirmation processing can be
performed on this conversation. The
transaction program can issue verbs and
recognize returned parameters relating to
confirmation.
syncpt
Indicates that syncpt and confirmation processing
can be performed on this conversation. The
transaction program can issue verbs and recognize
returned parameters relating to syncpt and
confirmation."
::= { appcActiveConvEntry 8 }
appcActiveConvSource OBJECT-TYPE
SYNTAX INTEGER {
localLu(1),
partnerLu(2)
}
Allen, et. al. Standards Track [Page 98]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates whether the local or partner LU is the source of the
conversation, that is, which LU started the conversation by
sending the allocation request.
localLu
The local LU is the source of the conversation,
and the partner LU is the target of the
conversation.
partnerLu
The partner LU is the source of the
conversation, and the local LU is the target of
the conversation."
::= { appcActiveConvEntry 9 }
appcActiveConvDuplex OBJECT-TYPE
SYNTAX INTEGER {
half(1),
full(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the conversation duplex style in effect for the
conversation.
half Indicates that information can be transferred in
both directions, but only in one direction at a
time.
full Indicates that information can be transferred in
both directions at the same time."
::= { appcActiveConvEntry 10 }
appcActiveConvUpTime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The length of time since the conversation started, measured in
hundredths of a second."
::= { appcActiveConvEntry 11 }
Allen, et. al. Standards Track [Page 99]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcActiveConvSendBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the number of bytes that was sent on the
conversation. The count includes all SNA RU bytes sent,
including those in the FMH-5 (Attach), FMH-7 (Error
Description), SIGNAL, LUSTAT, and SNA responses; it does not
include SNA TH and RH bytes."
::= { appcActiveConvEntry 12 }
appcActiveConvRcvBytes OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates the number of bytes that was received on the
conversation. The count includes all SNA RU bytes sent,
including those in the FMH-5 (Attach), FMH-7 (Error
Description), SIGNAL, LUSTAT, and SNA responses; it does not
include SNA TH and RH bytes."
::= { appcActiveConvEntry 13 }
appcActiveConvUserid OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..10))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The user ID that the initiating program provided in the
incoming attach."
::= { appcActiveConvEntry 14 }
appcActiveConvPcidNauName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0 | 3..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network-qualified NAU name of the
node at which the session and PCID originated. For APPN
and LEN nodes, this is either CP name of the APPN node at
which the origin LU is located or the CP name of the
NN serving the LEN node at which the origin LU is
located. This field is from 3 to 17 characters in
length, including a period (.) which separates the
Allen, et. al. Standards Track [Page 100]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
NetId from the NAU name. A null string indicates
that the value is unknown."
::= { appcActiveConvEntry 15 }
appcActiveConvPcid OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0|8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The procedure correlation identifier (PCID) of the session.
It is an 8-octet value assigned by the control point providing
session services for the primary LU. A null string indicates
that the value is unknown."
::= { appcActiveConvEntry 16 }
appcActiveConvModeName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Mode Name used for this conversation.
This is a 1-8 character name."
::= { appcActiveConvEntry 17 }
appcActiveConvLuwIdName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The SNA name of the LU that initiated the logical unit of work
that is associated with this active TP. This field is from
1 to 17 characters in length, including a period (.) which
separates the NetId from the LU name if the NetId is present."
::= { appcActiveConvEntry 18 }
appcActiveConvLuwIdInstance OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..6))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The instance identifier for the logical unit of work."
::= { appcActiveConvEntry 19 }
Allen, et. al. Standards Track [Page 101]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcActiveConvLuwIdSequence OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sequence identifier for the logical unit of work."
::= { appcActiveConvEntry 20 }
appcActiveConvTpName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transaction program name which started this conversation.
This name could either be from a FMH5 ATTACH for a remotely
started conversation, otherwise it could the name of the local
TP if available.
When the TP name consists entirely of displayable EBCDIC code
points, it is mapped directly to the equivalent ASCII display
string. However, registered TP names always have a non-
displayable EBCDIC code point (value less than or equal to
x'3F') as the first character, so they cannot be directly
mapped to an ASCII display string. These TP names are
converted to a display string that is equivalent to a
hexadecimal display of the EBCDIC code points. For example,
the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte
ASCII display string '06F1' (including the two single quotes).
This name is NULL if the conversation is started locally
(i.e., not with a FMH5 ATTACH)."
::= { appcActiveConvEntry 21 }
-- *********************************************************************
-- APPC Historical Conversation Table
-- This table contains historical information about APPC
-- conversations that ended abnormally. It is an implementation
-- choice how long to retain information on a given conversation.
-- *********************************************************************
appcHistConvTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcHistConvEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Table of historical information about APPC Conversations that
Allen, et. al. Standards Track [Page 102]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
ended in error. Possible categories of error conditions that
could be saved in this table are:
- allocation errors,
- deallocate abend,
- program errors, and
- service errors."
::= { appcConversation 2 }
appcHistConvEntry OBJECT-TYPE
SYNTAX AppcHistConvEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry representing one APPC Conversation."
INDEX
{ appcHistConvIndex }
::= { appcHistConvTable 1}
AppcHistConvEntry ::= SEQUENCE {
appcHistConvIndex Integer32,
appcHistConvEndTime DateAndTime,
appcHistConvLocLuName DisplayString,
appcHistConvParLuName DisplayString,
appcHistConvTpName DisplayString,
appcHistConvPcidNauName DisplayString,
appcHistConvPcid OCTET STRING,
appcHistConvSenseData SnaSenseData,
appcHistConvLogData OCTET STRING,
appcHistConvEndedBy INTEGER
}
appcHistConvIndex OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index for entry in Conversation table. This value identifies
the unique index of the conversation. It is recommended that
an Agent not reuse the index of a deactivated conversation for
a significant period of time (e.g. one week)."
::= { appcHistConvEntry 1 }
appcHistConvEndTime OBJECT-TYPE
Allen, et. al. Standards Track [Page 103]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time at which the conversation ended."
::= { appcHistConvEntry 2 }
appcHistConvLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The name of the local LU for this conversation. This field is
from 1 to 17 characters in length, including a period (.) which
separates the NetId from the NAU name if the NetId is present."
::= { appcHistConvEntry 3 }
appcHistConvParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The SNA name of the partner LU for the conversation. This
field is from 1 to 17 characters in length, including a period
(.) which separates the NetId from the NAU name if the NetId is
present."
::= { appcHistConvEntry 4 }
appcHistConvTpName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The transaction program name which started this conversation.
This name could either be from a FMH5 ATTACH for a remotely
started conversation, otherwise it could the name of the local
TP if available.
When the TP name consists entirely of displayable EBCDIC code
points, it is mapped directly to the equivalent ASCII display
string. However, registered TP names always have a non-
displayable EBCDIC code point (value less than or equal to
x'3F') as the first character, so they cannot be directly
mapped to an ASCII display string. These TP names are
converted to a display string that is equivalent to a
Allen, et. al. Standards Track [Page 104]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
hexadecimal display of the EBCDIC code points. For example,
the 2-byte TP name x'06F1' (CNOS) is converted to the 6-byte
ASCII display string '06F1' (including the two single quotes).
This name is NULL if the conversation is started locally
(i.e., not with a FMH5 ATTACH)."
::= { appcHistConvEntry 5 }
appcHistConvPcidNauName OBJECT-TYPE
SYNTAX DisplayString (SIZE (0 | 3..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The network-qualified NAU name of the
node at which the session and PCID originated. For APPN
and LEN nodes, this is either CP name of the APPN node at
which the origin LU is located or the CP name of the
NN serving the LEN node at which the origin LU is
located. This field is from 3 to 17 characters in
length, including a period (.) which separates the
NetId from the NAU name. A null string indicates that the
value is unknown."
::= { appcHistConvEntry 6 }
appcHistConvPcid OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0|8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The procedure correlation identifier (PCID) of the session.
It is an 8-octet value assigned by the control point providing
session services for the primary LU. A null string indicates
that the value is unknown."
::= { appcHistConvEntry 7 }
appcHistConvSenseData OBJECT-TYPE
SYNTAX SnaSenseData
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The sense data associated with the action that ended this
conversation, e.g., FMH-7 or UNBIND."
::= { appcHistConvEntry 8 }
Allen, et. al. Standards Track [Page 105]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcHistConvLogData OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (0..32))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The first 32 bytes of the data portion of the Log Data GDS
Variable that is associated with the last FMH-7 that occurred
on this conversation. If there was no Log Data GDS Variable
associated with the FMH-7, this object is null.
This object reflects only the data portion of the Log Data
GDS Variable (i.e. not the LL or GDS Id)."
::= { appcHistConvEntry 9 }
appcHistConvEndedBy OBJECT-TYPE
SYNTAX INTEGER {
localLu(1),
partnerLu(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Indicates which LU ended the conversation."
::= { appcHistConvEntry 10 }
-- *********************************************************************
-- APPC CPIC Admin Table
-- Objects in this table contain default or expected configuration
-- values for CPI-C side information.
-- *********************************************************************
appcCpicAdminTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcCpicAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"APPC CPI-C side information table."
::= { appcCPIC 1 }
appcCpicAdminEntry OBJECT-TYPE
SYNTAX AppcCpicAdminEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry of APPC CPI-C side information Table."
Allen, et. al. Standards Track [Page 106]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
INDEX { appcCpicAdminLocLuName,
appcCpicAdminSymbDestName }
::= { appcCpicAdminTable 1 }
AppcCpicAdminEntry ::= SEQUENCE {
appcCpicAdminLocLuName DisplayString,
appcCpicAdminSymbDestName DisplayString,
appcCpicAdminParLuAlias DisplayString,
appcCpicAdminParLuName DisplayString,
appcCpicAdminModeName DisplayString,
appcCpicAdminTpNameType INTEGER,
appcCpicAdminTpName DisplayString,
appcCpicAdminUserid DisplayString,
appcCpicAdminSecurity INTEGER
}
appcCpicAdminLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNA name of the local LU to which this CPI-C side
information definition applies. This field is from 1 to 17
characters in length, including a period (.) which separates
the NetId from the NAU name if the NetId is present.
The reserved value '*ALL' indicates that the definition applies
to all local LUs, and not just to a single local LU."
::= { appcCpicAdminEntry 1 }
appcCpicAdminSymbDestName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the symbolic destination name used by CPI-C
applications to identify this definition."
::= { appcCpicAdminEntry 2 }
appcCpicAdminParLuAlias OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A local alias for the partner LU. If not known or
Allen, et. al. Standards Track [Page 107]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
not applicable, this object contains a zero-length
string."
::= { appcCpicAdminEntry 3 }
appcCpicAdminParLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The SNA name of the partner LU. This field is from 1 to 17
characters in length, including a period (.) which separates
the NetId from the NAU name if the NetId is present."
::= { appcCpicAdminEntry 4 }
appcCpicAdminModeName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the mode name. A mode defines the characteristics
for a group of sessions. The mode name can be blank (8 space
characters)."
::= { appcCpicAdminEntry 5 }
appcCpicAdminTpNameType OBJECT-TYPE
SYNTAX INTEGER {
normal(1),
snaServiceTp(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether the TP name in appcCpicAdminTpName
identifies a normal TP or an SNA service TP. In this context,
a normal TP is one with a name consisting only of displayable
characters, while an SNA service TP has a name containing
octets that do not map to displayable characters."
::= { appcCpicAdminEntry 6 }
appcCpicAdminTpName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..64))
Allen, et. al. Standards Track [Page 108]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the name of the partner TP to be used when a CPI-C
application initiates a conversation specifying this side
information entry.
Display convention
When the TP name consists entirely of displayable EBCDIC
code points, it is mapped directly to the equivalent ASCII
display string. However, registered TP names always have a
non-displayable EBCDIC code point (value less than or equal
to x'3F') as the first character, so they cannot be
directly mapped to an ASCII display string. These TP names
are converted to a display string that is equivalent to a
hexadecimal display of the EBCDIC code points. For
example, the 2-byte TP name x'06F1' (CNOS) is converted to
the 6-byte ASCII display string '06F1' (including the two
single quotes)."
::= { appcCpicAdminEntry 7 }
appcCpicAdminUserid OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..10))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The security userid, if any, associated with the side
information definition."
::= { appcCpicAdminEntry 8 }
appcCpicAdminSecurity OBJECT-TYPE
SYNTAX INTEGER {
none(1),
same(2),
pgm(3),
pgmStrong(4),
distributed(5),
mutual(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the security information to be used for allocating
the conversation.
Allen, et. al. Standards Track [Page 109]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
none - No security information.
same - Use the security environment currently
associated with this TP.
pgm - Use the program-supplied user_id and password.
pgmStrong - Use the program-supplied user_id and password.
The local LU will insure that the password is
not exposed in clear-text form on the physical
network.
distributed - Use the security environment and a distributed
security system to generate the authentication
information for this request. If distributed
security tokens cannot be generated, then fail
the conversation.
mutual - Authenticate both the user to the destination
system and the destination system to the user."
::= { appcCpicAdminEntry 9 }
-- *********************************************************************
-- APPC CPIC Oper Table
-- Objects in this table contain current operational values, such
-- as state values or negotiated parameters, for CPI-C side
-- information.
-- *********************************************************************
appcCpicOperTable OBJECT-TYPE
SYNTAX SEQUENCE OF AppcCpicOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"APPC CPI-C side information operational table."
::= { appcCPIC 2 }
appcCpicOperEntry OBJECT-TYPE
SYNTAX AppcCpicOperEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry of APPC CPI-C side information Table."
INDEX { appcCpicOperLocLuName,
appcCpicOperSymbDestName }
::= { appcCpicOperTable 1 }
Allen, et. al. Standards Track [Page 110]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
AppcCpicOperEntry ::= SEQUENCE {
appcCpicOperLocLuName DisplayString,
appcCpicOperSymbDestName DisplayString,
appcCpicOperParLuAlias DisplayString,
appcCpicOperParLuName DisplayString,
appcCpicOperModeName DisplayString,
appcCpicOperTpNameType INTEGER,
appcCpicOperTpName DisplayString,
appcCpicOperUserid DisplayString,
appcCpicOperSecurity INTEGER
}
appcCpicOperLocLuName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SNA name of the local LU to which this CPI-C side
information definition applies. This field is from 1 to 17
characters in length, including a period (.) which separates
the NetId from the NAU name if the NetId is present.
The reserved value '*ALL' indicates that the definition applies
to all local LUs, and not just to a single local LU."
::= { appcCpicOperEntry 1 }
appcCpicOperSymbDestName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Specifies the symbolic destination name used by CPI-C
applications to identify this definition."
::= { appcCpicOperEntry 2 }
appcCpicOperParLuAlias OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A local alias for the partner LU. If not known or not
applicable, this object contains a zero-length string."
::= { appcCpicOperEntry 3 }
appcCpicOperParLuName OBJECT-TYPE
Allen, et. al. Standards Track [Page 111]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
SYNTAX DisplayString (SIZE (1..17))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The SNA name of the partner LU. This field is from 1 to 17
characters in length, including a period (.) which separates
the NetId from the NAU name if the NetId is present."
::= { appcCpicOperEntry 4 }
appcCpicOperModeName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the mode name. A mode defines the characteristics
for a group of sessions. The mode name can be blank (8 space
characters)."
::= { appcCpicOperEntry 5 }
appcCpicOperTpNameType OBJECT-TYPE
SYNTAX INTEGER {
normal(1),
snaServiceTp(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies whether the TP name in appcCpicOperTpName identifies
a normal TP or an SNA service TP. In this context, a normal TP
is one with a name consisting only of displayable characters,
while an SNA service TP has a name containing octets that do
not map to displayable characters."
::= { appcCpicOperEntry 6 }
appcCpicOperTpName OBJECT-TYPE
SYNTAX DisplayString (SIZE (1..64))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the name of the partner TP to be used when a CPI-C
application initiates a conversation specifying this side
information entry.
Allen, et. al. Standards Track [Page 112]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
Display convention
When the TP name consists entirely of displayable EBCDIC
code points, it is mapped directly to the equivalent ASCII
display string. However, registered TP names always have
a non-displayable EBCDIC code point (value less than or
equal to x'3F') as the first character, so they cannot be
directly mapped to an ASCII display string. These TP
names are converted to a display string that is equivalent
to a hexadecimal display of the EBCDIC code points. For
example, the 2-byte TP name x'06F1' (CNOS) is converted to
the 6-byte ASCII display string '06F1' (including the two
single quotes)."
::= { appcCpicOperEntry 7 }
appcCpicOperUserid OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..10))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The security userid, if any, associated with the active side
information definition."
::= { appcCpicOperEntry 8 }
appcCpicOperSecurity OBJECT-TYPE
SYNTAX INTEGER {
none(1),
same(2),
pgm(3),
pgmStrong(4),
distributed(5),
mutual(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Specifies the security information to be used for allocating
the conversation.
none - No security information.
same - Use the security environment currently
associated with this TP.
pgm - Use the program-supplied user_id and password.
pgmStrong - Use the program-supplied user_id and password.
The local LU will insure that the password is
not exposed in clear-text form on the physical
Allen, et. al. Standards Track [Page 113]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
network.
distributed - Use the security environment and a distributed
security system to generate the authentication
information for this request. If distributed
security tokens cannot be generated, then fail
the conversation.
mutual - Authenticate both the user to the destination
system and the destination system to the user."
::= { appcCpicOperEntry 9 }
-- ***************************************************************
-- Conformance information
-- ***************************************************************
appcConformance OBJECT IDENTIFIER ::= {appcMIB 2 }
appcCompliances OBJECT IDENTIFIER ::= {appcConformance 1 }
appcGroups OBJECT IDENTIFIER ::= {appcConformance 2 }
-- Compliance statements
appcCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for the SNMPv2 entities which
implement the APPC MIB."
MODULE -- this module
-- Unconditionally mandatory groups
MANDATORY-GROUPS {
appcGlobalConfGroup,
appcLluConfGroup,
appcParLuConfGroup,
appcModeConfGroup,
appcTpConfGroup,
appcSessionConfGroup
}
-- Conditionally mandatory groups
GROUP appcControlConfGroup
DESCRIPTION
"The appcControlConfGroup is mandatory only for those
entities which implement activation and deactivation of
specific controls such as statistics collecting and
counting."
Allen, et. al. Standards Track [Page 114]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
GROUP appcCnosConfGroup
DESCRIPTION
"The appcCnosConfGroup is mandatory only for those entities
which implement CNOS. "
GROUP appcCpicConfGroup
DESCRIPTION
"The appcCpicConfGroup is mandatory only for those entities
which implement CPI-C. "
GROUP appcConversationConfGroup
DESCRIPTION
"The appcConversationConfGroup is mandatory only for those
entities which implement session endpoints for non-control
APPC sessions."
-- MIN-ACCESS for objects
OBJECT appcActSessOperState
MIN-ACCESS read-only
DESCRIPTION
"An implementation is not required to support session
deactivation via this object."
::= {appcCompliances 1 }
-- Units of conformance
appcGlobalConfGroup OBJECT-GROUP
OBJECTS {
appcUpTime,
appcDefaultModeName,
appcDefaultLuName,
appcDefaultImplInbndPlu,
appcDefaultMaxMcLlSndSize,
appcDefaultFileSpec,
appcDefaultTpOperation,
appcDefaultTpConvSecRqd,
appcLocalCpName,
appcActiveSessions,
appcActiveHprSessions
}
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation of APPC
global information and defaults."
::= { appcGroups 1 }
Allen, et. al. Standards Track [Page 115]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcLluConfGroup OBJECT-GROUP
OBJECTS {
appcLluAdminDepType,
appcLluAdminLocalAddress,
appcLluAdminSessLimit,
appcLluAdminBindRspMayQ,
appcLluAdminCompression,
appcLluAdminInBoundCompLevel,
appcLluAdminOutBoundCompLevel,
appcLluAdminCompRleBeforeLZ,
appcLluAdminAlias,
appcLluOperDepType,
appcLluOperLocalAddress,
appcLluOperSessLimit,
appcLluOperBindRspMayQ,
appcLluOperCompression,
appcLluOperInBoundCompLevel,
appcLluOperOutBoundCompLevel,
appcLluOperCompRleBeforeLZ,
appcLluOperAlias,
appcLluOperActiveSessions
}
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation of APPC
local LU6.2s."
::= { appcGroups 2 }
appcParLuConfGroup OBJECT-GROUP
OBJECTS {
appcLuPairAdminParLuAlias,
appcLuPairAdminSessLimit,
appcLuPairAdminSessSec,
appcLuPairAdminSecAccept,
appcLuPairAdminLinkObjId,
appcLuPairAdminParaSessSup,
appcLuPairOperParLuAlias,
appcLuPairOperSessLimit,
appcLuPairOperSessSec,
appcLuPairOperSecAccept,
appcLuPairOperLinkObjId,
appcLuPairOperParaSessSup,
appcLuPairOperParaSessSupLS,
appcLuPairOperState
}
Allen, et. al. Standards Track [Page 116]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation of APPC
partner LUs."
::= { appcGroups 3 }
appcModeConfGroup OBJECT-GROUP
OBJECTS {
appcModeAdminCosName,
appcModeAdminSessEndTpName,
appcModeAdminMaxSessLimit,
appcModeAdminMinCwinLimit,
appcModeAdminMinClosLimit,
appcModeAdminConWinAutoActLmt,
appcModeAdminRecvPacWinSz,
appcModeAdminSendPacWinSz,
appcModeAdminPrefRecvRuSz,
appcModeAdminPrefSendRuSz,
appcModeAdminRecvRuSzUpBnd,
appcModeAdminSendRuSzUpBnd,
appcModeAdminRecvRuSzLoBnd,
appcModeAdminSendRuSzLoBnd,
appcModeAdminSingSessReinit,
appcModeAdminCompression,
appcModeAdminInBoundCompLevel,
appcModeAdminOutBoundCompLevel,
appcModeAdminCompRleBeforeLZ,
appcModeAdminSyncLvl,
appcModeAdminCrypto,
appcModeOperCosName,
appcModeOperSessEndTpName,
appcModeOperSessLimit,
appcModeOperMaxSessLimit,
appcModeOperMinCwinLimit,
appcModeOperMinClosLimit,
appcModeOperConWinAutoActLmt,
appcModeOperRecvPacWinSz,
appcModeOperSendPacWinSz,
appcModeOperPrefRecvRuSz,
appcModeOperPrefSendRuSz,
appcModeOperRecvRuSzUpBnd,
appcModeOperSendRuSzUpBnd,
appcModeOperRecvRuSzLoBnd,
appcModeOperSendRuSzLoBnd,
appcModeOperSingSessReinit,
Allen, et. al. Standards Track [Page 117]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcModeOperCompression,
appcModeOperInBoundCompLevel,
appcModeOperOutBoundCompLevel,
appcModeOperCompRleBeforeLZ,
appcModeOperSyncLvl,
appcModeOperCrypto,
appcModeOperSyncLvlLastStart,
appcModeOperCryptoLastStart,
appcModeOperCNOSNeg,
appcModeOperActCwin,
appcModeOperActClos,
appcModeOperPndCwin,
appcModeOperPndClos,
appcModeOperPtmCwin,
appcModeOperPtmClos,
appcModeOperDrainSelf,
appcModeOperDrainPart
}
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation of APPC
modes."
::= { appcGroups 4 }
appcTpConfGroup OBJECT-GROUP
OBJECTS {
appcTpAdminFileSpec,
appcTpAdminStartParm,
appcTpAdminTpOperation,
appcTpAdminInAttachTimeout,
appcTpAdminRcvAllocTimeout,
appcTpAdminSyncLvl,
appcTpAdminInstLmt,
appcTpAdminStatus,
appcTpAdminLongRun,
appcTpAdminConvType,
appcTpAdminConvDuplex,
appcTpAdminConvSecReq,
appcTpAdminVerPip,
appcTpAdminPipSubNum
}
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation of APPC
Transaction Programs."
::= { appcGroups 5 }
Allen, et. al. Standards Track [Page 118]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcSessionConfGroup OBJECT-GROUP
OBJECTS {
appcActSessPcidCpName,
appcActSessPcid,
appcActSessPluIndicator,
appcActSessModeName,
appcActSessCosName,
appcActSessTransPriority,
appcActSessEnhanceSecSup,
appcActSessSendPacingType,
appcActSessSendRpc,
appcActSessSendNxWndwSize,
appcActSessRecvPacingType,
appcActSessRecvRpc,
appcActSessRecvNxWndwSize,
appcActSessRscv,
appcActSessInUse,
appcActSessMaxSndRuSize,
appcActSessMaxRcvRuSize,
appcActSessSndPacingSize,
appcActSessRcvPacingSize,
appcActSessOperState,
appcActSessUpTime,
appcActSessRtpNceId,
appcActSessRtpTcid,
appcActSessLinkIndex,
appcSessStatsSentFmdBytes,
appcSessStatsSentNonFmdBytes,
appcSessStatsRcvdFmdBytes,
appcSessStatsRcvdNonFmdBytes,
appcSessStatsSentFmdRus,
appcSessStatsSentNonFmdRus,
appcSessStatsRcvdFmdRus,
appcSessStatsRcvdNonFmdRus,
appcSessStatsCtrUpTime,
appcHistSessTime,
appcHistSessType,
appcHistSessLocLuName,
appcHistSessParLuName,
appcHistSessModeName,
appcHistSessUnbindType,
appcHistSessSenseData,
appcHistSessComponentId,
appcHistSessDetectModule,
appcSessRtpSessions
Allen, et. al. Standards Track [Page 119]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
}
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation of APPC
LU6.2 sessions."
::= { appcGroups 6 }
appcControlConfGroup OBJECT-GROUP
OBJECTS {
appcCntrlAdminStat,
appcCntrlAdminRscv,
appcCntrlAdminTrace,
appcCntrlAdminTraceParm,
appcCntrlOperStat,
appcCntrlOperStatTime,
appcCntrlOperRscv,
appcCntrlOperRscvTime,
appcCntrlOperTrace,
appcCntrlOperTraceTime,
appcCntrlOperTraceParm
}
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation of APPC
control."
::= { appcGroups 7 }
appcCnosConfGroup OBJECT-GROUP
OBJECTS {
appcCnosCommand,
appcCnosMaxSessLimit,
appcCnosMinCwinLimit,
appcCnosMinClosLimit,
appcCnosDrainSelf,
appcCnosDrainPart,
appcCnosResponsible,
appcCnosForce,
appcCnosTargetLocLuName,
appcCnosTargetParLuName,
appcCnosTargetModeName
}
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation of APPC
CNOS processing."
Allen, et. al. Standards Track [Page 120]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
::= { appcGroups 8 }
appcCpicConfGroup OBJECT-GROUP
OBJECTS {
appcCpicAdminParLuAlias,
appcCpicAdminParLuName,
appcCpicAdminModeName,
appcCpicAdminTpNameType,
appcCpicAdminTpName,
appcCpicAdminUserid,
appcCpicAdminSecurity,
appcCpicOperParLuAlias,
appcCpicOperParLuName,
appcCpicOperModeName,
appcCpicOperTpNameType,
appcCpicOperTpName,
appcCpicOperUserid,
appcCpicOperSecurity
}
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation of APPC
CPI-C side information."
::= { appcGroups 9 }
appcConversationConfGroup OBJECT-GROUP
OBJECTS {
appcActiveConvId,
appcActiveConvState,
appcActiveConvType,
appcActiveConvCorrelator,
appcActiveConvSyncLvl,
appcActiveConvSource,
appcActiveConvDuplex,
appcActiveConvUpTime,
appcActiveConvSendBytes,
appcActiveConvRcvBytes,
appcActiveConvUserid,
appcActiveConvPcidNauName,
appcActiveConvPcid,
appcActiveConvModeName,
appcActiveConvLuwIdName,
appcActiveConvLuwIdInstance,
appcActiveConvLuwIdSequence,
appcActiveConvTpName,
appcHistConvEndTime,
Allen, et. al. Standards Track [Page 121]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
appcHistConvLocLuName,
appcHistConvParLuName,
appcHistConvTpName,
appcHistConvPcidNauName,
appcHistConvPcid,
appcHistConvSenseData,
appcHistConvLogData,
appcHistConvEndedBy
}
STATUS current
DESCRIPTION
"A collection of objects providing the instrumentation of APPC
conversations."
::= { appcGroups 10 }
-- end of conformance statement
END
Allen, et. al. Standards Track [Page 122]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
5. Acknowledgments
This MIB module is the product of the SNA NAU MIB Working Group.
Special thanks to Wayne Clark, Cisco Systems; Rich Daugherty, IBM
Corporation; and Leo Temoshenko, IBM Corporation, for their
contributions and review.
6. References
[1] IBM, Systems Network Architecture Technical Overview, GC30-3073-4,
January, 1994.
[2] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Structure of Management Information for version 2 of
the Simple Network Management Protocol (SNMPv2)", RFC 1902, January
1996.
[3] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Textual Conventions for Version 2 of the Simple
Network Management Protocol (SNMPv2)", RFC 1903, January 1996.
[4] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S.
Waldbusser, "Conformance Statements for Version 2 of the Simple
Network Management Protocol (SNMPv2)", RFC 1904, January 1996.
[5] IBM, Systems Network Architecture Transaction Programmer's
Reference for LU Type 6.2, GC30-3084-05, June, 1993.
[6] IBM, Common Programming Interface Communications Specification 2.0,
SC31-6180-01, June, 1994.
[7] Kielczewski, Z., Kostick D., and K. Shih, "Definition of Managed
Objects for SNA NAUs using SMIv2", RFC 1666, Eicon Technology
Corporation, Bell Communications Research, Novell, August 1994.
7. Security Considerations
Security issues are not discussed in this memo.
Allen, et. al. Standards Track [Page 123]
RFC 2051 SNANAU APPC MIB using SMIv2 October 1996
8. Authors' Addresses
Michael Allen
Wall Data Inc.
P.O.Box 1120, WA 98019, USA
Phone: +1 206 844 3505
EMail: mallen@hq.walldata.com
Bob Clouston
Cisco Systems
7025 Kit Creek Road
PO Box 14987
Research Triangle Park, NC 27709, USA
Phone: +1 919 472 2333
EMail: clouston@cisco.com
Zbigniew Kielczewski
Cisco Systems
7025 Kit Creek Road
PO Box 14987
Research Triangle Park, NC 27709, USA
Phone: +1 919 472 2326
EMail: zbig@cisco.com
William Kwan
Jupiter Technology Inc.
200 Prospect St.
Waltham, MA 02254
Phone: 1 617 894-9300 x423
EMail: billk@jti.com
Bob Moore
IBM Corporation
800 Park Offices Drive
E87/664
P.O. Box 12195
Research Triangle Park, NC 27709, USA
Phone: 1 919 254 4436
EMail: remoore@ralvm6.vnet.ibm.com
Allen, et. al. Standards Track [Page 124]
|
