Network Working Group D. Borman
Request for Comments: 2675 Berkeley Software Design
Obsoletes: 2147 S. Deering
Category: Standards Track Cisco
R. Hinden
Nokia
August 1999
IPv6 Jumbograms
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (1999). All Rights Reserved.
Abstract
A "jumbogram" is an IPv6 packet containing a payload longer than
65,535 octets. This document describes the IPv6 Jumbo Payload
option, which provides the means of specifying such large payload
lengths. It also describes the changes needed to TCP and UDP to make
use of jumbograms.
Jumbograms are relevant only to IPv6 nodes that may be attached to
links with a link MTU greater than 65,575 octets, and need not be
implemented or understood by IPv6 nodes that do not support
attachment to links with such large MTUs.
1. Introduction
jumbo (jum'bO),
n., pl. -bos, adj.
-n.
1. a person, animal, or thing very large of its kind.
-adj.
2. very large: the jumbo box of cereal.
[1800-10; orig. uncert.; popularized as the name of a large
elephant purchased and exhibited by P.T. Barnum in 1882]
-- www.infoplease.com
Borman, et al. Standards Track [Page 1]
RFC 2675 IPv6 Jumbograms August 1999
The IPv6 header [IPv6] has a 16-bit Payload Length field and,
therefore, supports payloads up to 65,535 octets long. This document
specifies an IPv6 hop-by-hop option, called the Jumbo Payload option,
that carries a 32-bit length field in order to allow transmission of
IPv6 packets with payloads between 65,536 and 4,294,967,295 octets in
length. Packets with such long payloads are referred to as
"jumbograms".
The Jumbo Payload option is relevant only for IPv6 nodes that may be
attached to links with a link MTU greater than 65,575 octets (that
is, 65,535 + 40, where 40 octets is the size of the IPv6 header).
The Jumbo Payload option need not be implemented or understood by
IPv6 nodes that do not support attachment to links with MTU greater
than 65,575.
On links with configurable MTUs, the MTU must not be configured to a
value greater than 65,575 octets if there are nodes attached to that
link that do not support the Jumbo Payload option and it can not be
guaranteed that the Jumbo Payload option will not be sent to those
nodes.
The UDP header [UDP] has a 16-bit Length field which prevents it from
making use of jumbograms, and though the TCP header [TCP] does not
have a Length field, both the TCP MSS option and the TCP Urgent field
are constrained to 16 bits. This document specifies some simple
enhancements to TCP and UDP to enable them to make use of jumbograms.
An implementation of TCP or UDP on an IPv6 node that supports the
Jumbo Payload option must include the enhancements specified here.
Note: The 16 bit checksum used by UDP and TCP becomes less accurate
as the length of the data being checksummed is increased.
Application designers may want to take this into consideration.
1.1 Document History
This document merges and updates material that was previously
published in two separate documents:
- The specification of the Jumbo Payload option previously appeared
as part of the IPv6 specification in RFC 1883. RFC 1883 has been
superseded by RFC 2460, which no longer includes specification of
the Jumbo Payload option.
- The specification of TCP and UDP enhancements to support
jumbograms previously appeared as RFC 2147. RFC 2147 is obsoleted
by this document.
Borman, et al. Standards Track [Page 2]
RFC 2675 IPv6 Jumbograms August 1999
2. Format of the Jumbo Payload Option
The Jumbo Payload option is carried in an IPv6 Hop-by-Hop Options
header, immediately following the IPv6 header. This option has an
alignment requirement of 4n + 2. (See [IPv6, Section 4.2] for
discussion of option alignment.) The option has the following
format:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Option Type | Opt Data Len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Jumbo Payload Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Option Type 8-bit value C2 (hexadecimal).
Opt Data Len 8-bit value 4.
Jumbo Payload Length 32-bit unsigned integer. Length of the IPv6
packet in octets, excluding the IPv6 header
but including the Hop-by-Hop Options header
and any other extension headers present.
Must be greater than 65,535.
3. Usage of the Jumbo Payload Option
The Payload Length field in the IPv6 header must be set to zero in
every packet that carries the Jumbo Payload option.
If a node that understands the Jumbo Payload option receives a packet
whose IPv6 header carries a Payload Length of zero and a Next Header
value of zero (meaning that a Hop-by-Hop Options header follows), and
whose link-layer framing indicates the presence of octets beyond the
IPv6 header, the node must proceed to process the Hop-by-Hop Options
header in order to determine the actual length of the payload from
the Jumbo Payload option.
The Jumbo Payload option must not be used in a packet that carries a
Fragment header.
Higher-layer protocols that use the IPv6 Payload Length field to
compute the value of the Upper-Layer Packet Length field in the
checksum pseudo-header described in [IPv6, Section 8.1] must instead
use the Jumbo Payload Length field for that computation, for packets
that carry the Jumbo Payload option.
Borman, et al. Standards Track [Page 3]
RFC 2675 IPv6 Jumbograms August 1999
Nodes that understand the Jumbo Payload option are required to detect
a number of possible format errors, and if the erroneous packet was
not destined to a multicast address, report the error by sending an
ICMP Parameter Problem message [ICMPv6] to the packet's source. The
following list of errors specifies the values to be used in the Code
and Pointer fields of the Parameter Problem message:
error: IPv6 Payload Length = 0 and
IPv6 Next Header = Hop-by-Hop Options and
Jumbo Payload option not present
Code: 0
Pointer: high-order octet of the IPv6 Payload Length
error: IPv6 Payload Length != 0 and
Jumbo Payload option present
Code: 0
Pointer: Option Type field of the Jumbo Payload option
error: Jumbo Payload option present and
Jumbo Payload Length < 65,536
Code: 0
Pointer: high-order octet of the Jumbo Payload Length
error: Jumbo Payload option present and
Fragment header present
Code: 0
Pointer: high-order octet of the Fragment header.
A node that does not understand the Jumbo Payload option is expected
to respond to erroneously-received jumbograms as follows, according
to the IPv6 specification:
error: IPv6 Payload Length = 0 and
IPv6 Next Header = Hop-by-Hop Options
Code: 0
Pointer: high-order octet of the IPv6 Payload Length
error: IPv6 Payload Length != 0 and
Jumbo Payload option present
Code: 2
Pointer: Option Type field of the Jumbo Payload option
Borman, et al. Standards Track [Page 4]
RFC 2675 IPv6 Jumbograms August 1999
4. UDP Jumbograms
The 16-bit Length field of the UDP header limits the total length of
a UDP packet (that is, a UDP header plus data) to no greater than
65,535 octets. This document specifies the following modification of
UDP to relax that limit: UDP packets longer than 65,535 octets may be
sent by setting the UDP Length field to zero, and letting the
receiver derive the actual UDP packet length from the IPv6 payload
length. (Note that, prior to this modification, zero was not a legal
value for the UDP Length field, because the UDP packet length
includes the UDP header and therefore has a minimum value of 8.)
The specific requirements for sending a UDP jumbogram are as follows:
When sending a UDP packet, if and only if the length of the UDP
header plus UDP data is greater than 65,535, set the Length field
in the UDP header to zero.
The IPv6 packet carrying such a large UDP packet will necessarily
include a Jumbo Payload option in a Hop-by-Hop Options header; set
the Jumbo Payload Length field of that option to be the actual
length of the UDP header plus data, plus the length of all IPv6
extension headers present between the IPv6 header and the UDP
header.
For generating the UDP checksum, use the actual length of the UDP
header plus data, NOT zero, in the checksum pseudo-header [IPv6,
Section 8.1].
The specific requirements for receiving a UDP jumbogram are as
follows:
When receiving a UDP packet, if and only if the Length field in
the UDP header is zero, calculate the actual length of the UDP
header plus data from the IPv6 Jumbo Payload Length field minus
the length of all extension headers present between the IPv6
header and the UDP header.
In the unexpected case that the UDP Length field is zero but no
Jumbo Payload option is present (i.e., the IPv6 packet is not a
jumbogram), use the Payload Length field in the IPv6 header, in
place of the Jumbo Payload Length field, in the above calculation.
For verifying the received UDP checksum, use the calculated length
of the UDP header plus data, NOT zero, in the checksum pseudo-
header.
Borman, et al. Standards Track [Page 5]
RFC 2675 IPv6 Jumbograms August 1999
5. TCP Jumbograms
Because there is no length field in the TCP header, there is nothing
limiting the length of an individual TCP packet. However, the MSS
value that is negotiated at the beginning of the connection limits
the largest TCP packet that can be sent, and the Urgent Pointer
cannot reference data beyond 65,535 bytes.
5.1 TCP MSS
When determining what MSS value to send, if the MTU of the directly
attached interface minus 60 [IPv6, Section 8.3] is greater than or
equal to 65,535, then set the MSS value to 65,535.
When an MSS value of 65,535 is received, it is to be treated as
infinity. The actual MSS is determined by subtracting 60 from the
value learned by performing Path MTU Discovery [MTU-DISC] over the
path to the TCP peer.
5.2 TCP Urgent Pointer
The Urgent Pointer problem could be fixed by adding a TCP Urgent
Pointer Option. However, since it is unlikely that applications
using jumbograms will also use Urgent Pointers, a less intrusive
change similar to the MSS change will suffice.
When a TCP packet is to be sent with an Urgent Pointer (i.e., the URG
bit set), first calculate the offset from the Sequence Number to the
Urgent Pointer. If the offset is less than 65,535, fill in the
Urgent field and continue with the normal TCP processing. If the
offset is greater than 65,535, and the offset is greater than or
equal to the length of the TCP data, fill in the Urgent Pointer with
65,535 and continue with the normal TCP processing. Otherwise, the
TCP packet must be split into two pieces. The first piece contains
data up to, but not including the data pointed to by the Urgent
Pointer, and the Urgent field is set to 65,535 to indicate that the
Urgent Pointer is beyond the end of this packet. The second piece
can then be sent with the Urgent field set normally.
Note: The first piece does not have to include all of the data up to
the Urgent Pointer. It can be shorter, just as long as it ends
within 65,534 bytes of the Urgent Pointer, so that the offset to the
Urgent Pointer in the second piece will be less than 65,535 bytes.
For TCP input processing, when a TCP packet is received with the URG
bit set and an Urgent field of 65,535, the Urgent Pointer is
calculated using an offset equal to the length of the TCP data,
rather than the offset in the Urgent field.
Borman, et al. Standards Track [Page 6]
RFC 2675 IPv6 Jumbograms August 1999
It should also be noted that though the TCP window is only 16-bits,
larger windows can be used through use of the TCP Window Scale option
[TCP-EXT].
6. Security Considerations
The Jumbo Payload option and TCP/UDP jumbograms do not introduce any
known new security concerns.
7. Authors' Addresses
David A. Borman
Berkeley Software Design, Inc.
4719 Weston Hills Drive
Eagan, MN 55123
USA
Phone: +1 612 405 8194
EMail: dab@bsdi.com
Stephen E. Deering
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Phone: +1 408 527 8213
EMail: deering@cisco.com
Robert M. Hinden
Nokia
313 Fairchild Drive
Mountain View, CA 94043
USA
Phone: +1 650 625 2004
EMail: hinden@iprg.nokia.com
Borman, et al. Standards Track [Page 7]
RFC 2675 IPv6 Jumbograms August 1999
8. References
[ICMPv6] Conta, A. and S. Deering, "ICMP for the Internet Protocol
Version 6 (IPv6)", RFC 2463, December 1998.
[IPv6] Deering, S. and R. Hinden, "Internet Protocol Version 6
(IPv6) Specification", RFC 2460, December 1998.
[MTU-DISC] McCann, J., Deering, S. and J. Mogul, "Path MTU Discovery
for IP Version 6", RFC 1981, August 1986.
[TCP] Postel, J., "Transmission Control Protocol", STD 7, RFC
793, September 1981.
[TCP-EXT] Jacobson, V., Braden, R. and D. Borman, "TCP Extensions
for High Performance", RFC 1323, May 1992.
[UDP] Postel, J., "User Datagram Protocol", STD 6, RFC 768,
August 1980.
Borman, et al. Standards Track [Page 8]
RFC 2675 IPv6 Jumbograms August 1999
9. Full Copyright Statement
Copyright (C) The Internet Society (1999). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Borman, et al. Standards Track [Page 9]
|
