Network Working Group C. Perkins
Request for Comments: 3158 USC/ISI
Category: Informational J. Rosenberg
dynamicsoft
H. Schulzrinne
Columbia University
August 2001
RTP Testing Strategies
Status of this Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2001). All Rights Reserved.
Abstract
This memo describes a possible testing strategy for RTP (real-time
transport protocol) implementations.
Table of Contents
1 Introduction. . . . . . . . . . . . . . . . . . . . . . 2
2 End systems . . . . . . . . . . . . . . . . . . . . . . 2
2.1 Media transport . . . . . . . . . . . . . . . . . 3
2.2 RTP Header Extension . . . . . . . . . . . . . . . 4
2.3 Basic RTCP . . . . . . . . . . . . . . . . . . . 4
2.3.1 Sender and receiver reports . . . . . . . . 4
2.3.2 RTCP source description packets . . . . . . 6
2.3.3 RTCP BYE packets . . . . . . . . . . . . . . 7
2.3.4 Application defined RTCP packets . . . . . . 7
2.4 RTCP transmission interval . . . . . . . . . . . . 7
2.4.1 Basic Behavior . . . . . . . . . . . . . . 8
2.4.2 Step join backoff . . . . . . . . . . . . 9
2.4.3 Steady State Behavior . . . . . . . . . . 11
2.4.4 Reverse Reconsideration . . . . . . . . . 12
2.4.5 BYE Reconsideration . . . . . . . . . . . 13
2.4.6 Timing out members . . . . . . . . . . . . 14
2.4.7 Rapid SR's . . . . . . . . . . . . . . . . 15
3 RTP translators . . . . . . . . . . . . . . . . . . . . 15
4 RTP mixers. . . . . . . . . . . . . . . . . . . . . . . 17
5 SSRC collision detection. . . . . . . . . . . . . . . . 18
Perkins, et al. Informational [Page 1]
RFC 3158 RTP Testing Strategies August 2001
6 SSRC Randomization. . . . . . . . . . . . . . . . . . . 19
7 Security Considerations . . . . . . . . . . . . . . . . 20
8 Authors' Addresses. . . . . . . . . . . . . . . . . . . 20
9 References. . . . . . . . . . . . . . . . . . . . . . . 21
Full Copyright Statement. . . . . . . . . . . . . . . . . 22
1 Introduction
This memo describes a possible testing strategy for RTP [1]
implementations. The tests are intended to help demonstrate
interoperability of multiple implementations, and to illustrate
common implementation errors. They are not intended to be an
exhaustive set of tests and passing these tests does not necessarily
imply conformance to the complete RTP specification.
2 End systems
The architecture for testing RTP end systems is shown in Figure 1.
+-----------------+
+--------+ Test instrument +-----+
| +-----------------+ |
| |
+-------+--------+ +-------+--------+
| First RTP | | Second RTP |
| implementation | | implementation |
+----------------+ +----------------+
Figure 1: Testing architecture
Both RTP implementations send packets to the test instrument, which
forwards packets from one implementation to the other. Unless
otherwise specified, packets are forwarded with no additional delay
and without loss. The test instrument is required to delay or
discard packets in some of the tests. The test instrument is
invisible to the RTP implementations - it merely simulates poor
network conditions.
The test instrument is also capable of logging packet contents for
inspection of their correctness.
A typical test setup might comprise three machines on a single
Ethernet segment. Two of these machines run the RTP implementations,
the third runs the test instrument. The test instrument is an
application level packet forwarder. Both RTP implementations are
instructed to send unicast RTP packets to the test instrument, which
forwards packets between them.
Perkins, et al. Informational [Page 2]
RFC 3158 RTP Testing Strategies August 2001
2.1 Media transport
The aim of these tests is to show that basic media flows can be
exchanged between the two RTP implementations. The initial test is
for the first RTP implementation to transmit and the second to
receive. If this succeeds, the process is reversed, with the second
implementation sending and the first receiving.
The receiving application should be able to handle the following edge
cases, in addition to normal operation:
o Verify reception of packets which contain padding.
o Verify reception of packets which have the marker bit set
o Verify correct operation during sequence number wrap-around.
o Verify correct operation during timestamp wrap-around.
o Verify that the implementation correctly differentiates packets
according to the payload type field.
o Verify that the implementation ignores packets with unsupported
payload types
o Verify that the implementation can playout packets containing a
CSRC list and non-zero CC field (see section 4).
The sending application should be verified to correctly handle the
following edge cases:
o If padding is used, verify that the padding length indicator
(last octet of the packet) is correctly set and that the length
of the data section of the packet corresponds to that of this
particular payload plus the padding.
o Verify correct handling of the M bit, as defined by the
profile.
o Verify that the SSRC is chosen randomly.
o Verify that the initial value of the sequence number is
randomly selected.
o Verify that the sequence number increments by one for each
packet sent.
o Verify correct operation during sequence number wrap-around.
Perkins, et al. Informational [Page 3]
RFC 3158 RTP Testing Strategies August 2001
o Verify that the initial value of the timestamp is randomly
selected.
o Verify correct increment of timestamp (dependent on the payload
format).
o Verify correct operation during timestamp wrap-around.
o Verify correct choice of payload type according to the chosen
payload format, profile and any session level control protocol.
2.2 RTP Header Extension
An RTP implementation which does not use an extended header should be
able to process packets containing an extension header by ignoring
the extension.
If an implementation makes use of the header extension, it should be
verified that the profile specific field and the length field of the
extension are set correctly, and that the length of the packet is
consistent.
2.3 Basic RTCP
An RTP implementation is required to send RTCP control packets in
addition to data packets. The architecture for testing basic RTCP
functions is that shown in Figure 1.
2.3.1 Sender and receiver reports
The first test requires both implementations to be run, but neither
sends data. It should be verified that RTCP packets are generated by
each implementation, and that those packets are correctly received by
the other implementation. It should also be verified that:
o all RTCP packets sent are compound packets
o all RTCP compound packets start with an empty RR packet
o all RTCP compound packets contain an SDES CNAME packet
The first implementation should then be made to transmit data
packets. It should be verified that that implementation now
generates SR packets in place of RR packets, and that the second
application now generates RR packets containing a single report
block. It should be verified that these SR and RR packets are
correctly received. The following features of the SR packets should
also be verified:
Perkins, et al. Informational [Page 4]
RFC 3158 RTP Testing Strategies August 2001
o that the length field is consistent with both the length of the
packet and the RC field
o that the SSRC in SR packets is consistent with that in the RTP
data packets
o that the NTP timestamp in the SR packets is sensible (matches
the wall clock time on the sending machine)
o that the RTP timestamp in the SR packets is consistent with
that in the RTP data packets
o that the packet and octet count fields in the SR packets are
consistent with the number of RTP data packets transmitted
In addition, the following features of the RR packets should also be
verified:
o that the SSRC in the report block is consistent with that in
the data packets being received
o that the fraction lost is zero
o that the cumulative number of packets lost is zero
o that the extended highest sequence number received is
consistent with the data packets being received (provided the
round trip time between test instrument and receiver is smaller
than the packet inter-arrival time, this can be directly
checked by the test instrument).
o that the interarrival jitter is small (a precise value cannot
be given, since it depends on the test instrument and network
conditions, but very little jitter should be present in this
scenario).
o that the last sender report timestamp is consistent with that
in the SR packets (i.e., each RR passing through the test
instrument should contain the middle 32 bits from the 64 bit
NTP timestamp of the last SR packet which passed through the
test instrument in the opposite direction).
o that the delay since last SR field is sensible (an estimate may
be made by timing the passage of an SR and corresponding RR
through the test instrument, this should closely agree with the
DLSR field)
Perkins, et al. Informational [Page 5]
RFC 3158 RTP Testing Strategies August 2001
It should also be verified that the timestamps, packet count and
octet count correctly wrap-around after the appropriate interval.
The next test is to show behavior in the presence of packet loss.
The first implementation is made to transmit data packets, which are
received by the second implementation. This time, however, the test
instrument is made to randomly drop a small fraction (1% is
suggested) of the data packets. The second implementation should be
able to receive the data packets and process them in a normal manner
(with, of course, some quality degradation). The RR packets should
show a loss fraction corresponding to the drop rate of the test
instrument and should show an increasing cumulative number of packets
lost.
The loss rate in the test instrument is then returned to zero and it
is made to delay each packet by some random amount (the exact amount
depends on the media type, but a small fraction of the average
interarrival time is reasonable). The effect of this should be to
increase the reported interarrival jitter in the RR packets.
If these tests succeed, the process should be repeated with the
second implementation transmitting and the first receiving.
2.3.2 RTCP source description packets
Both implementations should be run, but neither is required to
transmit data packets. The RTCP packets should be observed and it
should be verified that each compound packet contains an SDES packet,
that that packet contains a CNAME item and that the CNAME is chosen
according to the rules in the RTP specification and profile (in many
cases the CNAME should be of the form `example@10.0.0.1' but this may
be overridden by a profile definition).
If an application supports additional SDES items then it should be
verified that they are sent in addition to the CNAME with some SDES
packets (the exact rate at which these additional items are included
is dependent on the application and profile).
It should be verified that an implementation can correctly receive
NAME, EMAIL, PHONE, LOC, NOTE, TOOL and PRIV items, even if it does
not send them. This is because it may reasonably be expected to
interwork with other implementations which support those items.
Receiving and ignoring such packets is valid behavior.
It should be verified that an implementation correctly sets the
length fields in the SDES items it sends, and that the source count
and packet length fields are correct. It should be verified that
SDES fields are not zero terminated.
Perkins, et al. Informational [Page 6]
RFC 3158 RTP Testing Strategies August 2001
It should be verified that an implementation correctly receives SDES
items which do not terminate in a zero byte.
2.3.3 RTCP BYE packets
Both implementations should be run, but neither is required to
transmit data packets. The first implementation is then made to exit
and it should be verified that an RTCP BYE packet is sent. It should
be verified that the second implementation reacts to this BYE packet
and notes that the first implementation has left the session.
If the test succeeds, the implementations should be restarted and the
process repeated with the second implementation leaving the session.
It should be verified that implementations handle BYE packets
containing the optional reason for leaving text (ignoring the text is
acceptable).
2.3.4 Application defined RTCP packets
Tests for the correct response to application defined packets are
difficult to specify, since the response is clearly implementation
dependent. It should be verified that an implementation ignores APP
packets where the 4 octet name field is unrecognized.
Implementations which use APP packets should verify that they behave
as expected.
2.4 RTCP transmission interval
The basic architecture for performing tests of the RTCP transmission
interval is shown in Figure 2.
The test instrument is connected to the same LAN as the RTP
implementation being tested. It is assumed that the test instrument
is preconfigured with the addresses and ports used by the RTP
implementation, and is also aware of the RTCP bandwidth and
sender/receiver fractions. The tests can be conducted using either
multicast or unicast.
The test instrument must be capable of sending arbitrarily crafted
RTP and RTCP packets to the RTP implementation. The test instrument
should also be capable of receiving packets sent by the RTP
implementation, parsing them, and computing metrics based on those
packets.
Perkins, et al. Informational [Page 7]
RFC 3158 RTP Testing Strategies August 2001
+--------------+
| test |
| instrument |
+-----+--------+
|
------+-----------+-------------- LAN
|
+-------+--------+
| RTP |
| implementation |
+----------------+
Figure 2: Testing architecture for RTCP
It is furthermore assumed that a number of basic controls over the
RTP implementation exist. These controls are:
o the ability to force the implementation to send or not send RTP
packets at any desired point in time
o the ability to force the application to terminate its
involvement in the RTP session, and for this termination to be
known immediately to the test instrument
o the ability to set the session bandwidth and RTCP sender and
receiver fractions
The second of these is required only for the test of BYE
reconsideration, and is the only aspect of these tests not easily
implementable by pure automation. It will generally require manual
intervention to terminate the session from the RTP implementation and
to convey this to the test instrument through some non-RTP means.
2.4.1 Basic Behavior
The first test is to verify basic correctness of the implementation
of the RTCP transmission rules. This basic behavior consists of:
o periodic transmission of RTCP packets
o randomization of the interval for RTCP packet transmission
o correct implementation of the randomization interval
computations, with unconditional reconsideration
Perkins, et al. Informational [Page 8]
RFC 3158 RTP Testing Strategies August 2001
The RTP implementation acts as a receiver, and never sends any RTP
data packets. The implementation is configured with a large session
bandwidth, say 1 Mbit/s. This will cause the implementation to use
the minimal interval of 5s rather than the small interval based on
the session bandwidth and membership size. The implementation will
generate RTCP packets at this minimal interval, on average. The test
instrument generates no packets, but receives the RTCP packets
generated by the implementation. When an RTCP packet is received,
the time is noted by the test instrument. The difference in time
between each pair of subsequent packets (called the interval) is
computed. These intervals are stored, so that statistics based on
these intervals can be computed. It is recommended that this
observation process operate for at least 20 minutes.
An implementation passes this test if the intervals have the
following properties:
o the minimum interval is never less than 2 seconds or more than
2.5 seconds;
o the maximum interval is never more than 7 seconds or less than
5.5 seconds;
o the average interval is between 4.5 and 5.5 seconds;
o the number of intervals between x and x+500ms is less than the
number of intervals between x+500ms and x+1s, for any x.
In particular, an implementation fails if the packets are sent with a
constant interval.
2.4.2 Step join backoff
The main purpose of the reconsideration algorithm is to avoid a flood
of packets that might occur when a large number of users
simultaneously join an RTP session. Reconsideration therefore
exhibits a backoff behavior in sending of RTCP packets when group
sizes increase. This aspect of the algorithm can be tested in the
following manner.
The implementation begins operation. The test instrument waits for
the arrival of the first RTCP packet. When it arrives, the test
instrument notes the time and then immediately sends 100 RTCP RR
packets to the implementation, each with a different SSRC and SDES
CNAME. The test instrument should ensure that each RTCP packet is of
the same length. The instrument should then wait until the next RTCP
packet is received from the implementation, and the time of such
reception is noted.
Perkins, et al. Informational [Page 9]
RFC 3158 RTP Testing Strategies August 2001
Without reconsideration, the next RTCP packet will arrive within a
short period of time. With reconsideration, transmission of this
packet will be delayed. The earliest it can arrive depends on the
RTCP session bandwidth, receiver fraction, and average RTCP packet
size. The RTP implementation should be using the exponential
averaging algorithm defined in the specification to compute the
average RTCP packet size. Since this is dominated by the received
packets (the implementation has only sent one itself), the average
will be roughly equal to the length of the RTCP packets sent by the
test instrument. Therefore, the minimum amount of time between the
first and second RTCP packets from the implementation is:
T > 101 * S / ( B * Fr * (e-1.5) * 2 )
Where S is the size of the RTCP packets sent by the test instrument,
B is the RTCP bandwidth (normally five percent of the session
bandwidth), Fr is the fraction of RTCP bandwidth allocated to
receivers (normally 75 percent), and e is the natural exponent.
Without reconsideration, this minimum interval Te would be much
smaller:
Te > MAX( [ S / ( B * Fr * (e-1.5) * 2 ) ] , [ 2.5 / (e-1.5) ] )
B should be chosen sufficiently small so that T is around 60 seconds.
Reasonable choices for these parameters are B = 950 bits per second,
and S = 1024 bits. An implementation passes this test if the
interval between packets is not less than T above, and not more than
3 times T.
Note: in all tests the value chosen for B, the RTCP bandwidth, is
calculated including the lower layer UDP/IP headers. In a typical
IPv4 based implementation, these comprise 28 octets per packet. A
common mistake is to forget that these are included when choosing the
size of packets to transmit.
The test should be repeated for the case when the RTP implementation
is a sender. This is accomplished by having the implementation send
RTP packets at least once a second. In this case, the interval
between the first and second RTCP packets should be no less than:
T > S / ( B * Fs * (e-1.5) * 2 )
Where Fs is the fraction of RTCP bandwidth allocated to senders,
usually 25%. Note that this value of T is significantly smaller than
the interval for receivers.
Perkins, et al. Informational [Page 10]
RFC 3158 RTP Testing Strategies August 2001
2.4.3 Steady State Behavior
In addition to the basic behavior in section 2.4.1, an implementation
should correctly implement a number of other, slightly more advanced
features:
o scale the RTCP interval with the group size;
o correctly divide bandwidth between senders and receivers;
o correctly compute the RTCP interval when the user is a sender
The implementation begins operation as a receiver. The test
instrument waits for the first RTCP packet from the implementation.
When it arrives, the test instrument notes the time, and immediately
sends 50 RTCP RR packets and 50 RTCP SR packets to the
implementation, each with a different SSRC and SDES CNAME. The test
instrument then sends 50 RTP packets, using the 50 SSRC from the RTCP
SR packets. The test instrument should ensure that each RTCP packet
is of the same length. The instrument should then wait until the
next RTCP packet is received from the implementation, and the time of
such reception is noted. The difference between the reception of the
RTCP packet and the reception of the previous is computed and stored.
In addition, after every RTCP packet reception, the 100 RTCP and 50
RTP packets are retransmitted by the test instrument. This ensures
that the sender and member status of the 100 users does not time out.
The test instrument should collect the interval measurements figures
for at least 100 RTCP packets.
With 50 senders, the implementation should not try to divide the RTCP
bandwidth between senders and receivers, but rather group all users
together and divide the RTCP bandwidth equally. The test is deemed
successful if the average RTCP interval is within 5% of:
T = 101* S/B
Where S is the size of the RTCP packets sent by the test instrument,
and B is the RTCP bandwidth. B should be chosen sufficiently small
so that the value of T is on the order of tens of seconds or more.
Reasonable values are S=1024 bits and B=3.4 kb/s.
The previous test is repeated. However, the test instrument sends 10
RTP packets instead of 50, and 10 RTCP SR and 90 RTCP RR instead of
50 of each. In addition, the implementation is made to send at least
one RTP packet between transmission of every one of its own RTCP
packets.
Perkins, et al. Informational [Page 11]
RFC 3158 RTP Testing Strategies August 2001
In this case, the average RTCP interval should be within 5% of:
T = 11 * S / (B * Fs)
Where S is the size of the RTCP packets sent by the test instrument,
B is the RTCP bandwidth, and Fs is the fraction of RTCP bandwidth
allocated for senders (normally 25%). The values for B and S should
be chosen small enough so that T is on the order of tens of seconds.
Reasonable choices are S=1024 bits and B=1.5 kb/s.
2.4.4 Reverse Reconsideration
The reverse reconsideration algorithm is effectively the opposite of
the normal reconsideration algorithm. It causes the RTCP interval to
be reduced more rapidly in response to decreases in the group
membership. This is advantageous in that it keeps the RTCP
information as fresh as possible, and helps avoids some premature
timeout problems.
In the first test, the implementation joins the session as a
receiver. As soon as the implementation sends its first RTCP packet,
the test instrument sends 100 RTCP RR packets, each of the same
length S, and a different SDES CNAME and SSRC in each. It then waits
for the implementation to send another RTCP packet. Once it does,
the test instrument sends 100 BYE packets, each one containing a
different SSRC, but matching an SSRC from one of the initial RTCP
packets. Each BYE should also be the same size as the RTCP packets
sent by the test instrument. This is easily accomplished by using a
BYE reason to pad out the length. The time of the next RTCP packet
from the implementation is then noted. The delay T between this (the
third RTCP packet) and the previous should be no more than:
T < 3 * S / (B * Fr * (e-1.5) * 2)
Where S is the size of the RTCP and BYE packets sent by the test
instrument, B is the RTCP bandwidth, Fr is the fraction of the RTCP
bandwidth allocated to receivers, and e is the natural exponent. B
should be chosen such that T is on the order of tens of seconds. A
reasonable choice is S=1024 bits and B=168 bits per second.
This test demonstrates basic correctness of implementation. An
implementation without reverse reconsideration will not send its next
RTCP packet for nearly 100 times as long as the above amount.
In the second test, the implementation joins the session as a
receiver. As soon as it sends its first RTCP packet, the test
instrument sends 100 RTCP RR packets, each of the same length S,
followed by 100 BYE packets, also of length S. Each RTCP packet
Perkins, et al. Informational [Page 12]
RFC 3158 RTP Testing Strategies August 2001
carries a different SDES CNAME and SSRC, and is matched with
precisely one BYE packet with the same SSRC. This will cause the
implementation to see a rapid increase and then rapid drop in group
membership.
The test is deemed successful if the next RTCP packet shows up T
seconds after the first, and T is within:
2.5 / (e-1.5) < T < 7.5 / (e-1.5)
This tests correctness of the maintenance of the pmembers variable.
An incorrect implementation might try to execute reverse
reconsideration every time a BYE is received, as opposed to only when
the group membership drops below pmembers. If an implementation did
this, it would end up sending an RTCP packet immediately after
receiving the stream of BYE's. For this test to work, B must be
chosen to be a large value, around 1Mb/s.
2.4.5 BYE Reconsideration
The BYE reconsideration algorithm works in much the same fashion as
regular reconsideration, except applied to BYE packets. When a user
leaves the group, instead of sending a BYE immediately, it may delay
transmission of its BYE packet if others are sending BYE's.
The test for correctness of this algorithm is as follows. The RTP
implementation joins the group as a receiver. The test instrument
waits for the first RTCP packet. When the test instrument receives
this packet, the test instrument immediately sends 100 RTCP RR
packets, each of the same length S, and each containing a different
SSRC and SDES CNAME. Once the test instrument receives the next RTCP
packet from the implementation, the RTP implementation is made to
leave the RTP session, and this information is conveyed to the test
instrument through some non-RTP means. The test instrument then
sends 100 BYE packets, each with a different SSRC, and each matching
an SSRC from a previously transmitted RTCP packet. Each of these BYE
packets is also of size S. Immediately following the BYE packets,
the test instrument sends 100 RTCP RR packets, using the same
SSRC/CNAMEs as the original 100 RTCP packets.
The test is deemed successful if the implementation either never
sends a BYE, or if it does, the BYE is received by the test
instrument not earlier than T seconds, and not later than 3 * T
seconds, after the implementation left the session, where T is:
T = 100 * S / ( 2 * (e-1.5) * B )
Perkins, et al. Informational [Page 13]
RFC 3158 RTP Testing Strategies August 2001
S is the size of the RTCP and BYE packets, e is the natural exponent,
B is the RTCP bandwidth, and Fr is the RTCP bandwidth fraction for
receivers. S and B should be chosen so that T is on the order of 50
seconds. A reasonable choice is S=1024 bits and B=1.1 kb/s.
The transmission of the RTCP packets is meant to verify that the
implementation is ignoring non-BYE RTCP packets once it decides to
leave the group.
2.4.6 Timing out members
Active RTP participants are supposed to send periodic RTCP packets.
When a participant leaves the session, they may send a BYE, however
this is not required. Furthermore, BYE reconsideration may cause a
BYE to never be sent. As a result, participants must time out other
participants who have not sent an RTCP packet in a long time.
According to the specification, participants who have not sent an
RTCP packet in the last 5 intervals are timed out. This test
verifies that these timeouts are being performed correctly.
The RTP implementation joins a session as a receiver. The test
instrument waits for the first RTCP packet from the implementation.
Once it arrives, the test instrument sends 100 RTCP RR packets, each
with a different SDES and SSRC, and notes the time. This will cause
the implementation to believe that there are now 101 group
participants, causing it to increase its RTCP interval. The test
instrument continues to monitor the RTCP packets from the
implementation. As each RTCP packet is received, the time of its
reception is noted, and the interval between RTCP packets is stored.
The 100 participants spoofed by the test instrument should eventually
time out at the RTP implementation. This should cause the RTCP
interval to be reduced to its minimum.
The test is deemed successful if the interval between RTCP packets
after the first is no less than:
Ti > 101 * S / ( 2 * (e-1.5) * B * Fr)
and this minimum interval is sustained no later than Td seconds after
the transmission of the 100 RR's, where Td is:
Td = 7 * 101 * S / ( B * Fr )
and the interval between RTCP packets after this point is no less
than:
Tf > 2.5 / (e-1.5)
Perkins, et al. Informational [Page 14]
RFC 3158 RTP Testing Strategies August 2001
For this test to work, B and S must be chosen so Ti is on the order
of minutes. Recommended values are S = 1024 bits and B = 1.9 kbps.
2.4.7 Rapid SR's
The minimum interval for RTCP packets can be reduced for large
session bandwidths. The reduction applies to senders only. The
recommended algorithm for computing this minimum interval is 360
divided by the RTP session bandwidth, in kbps. For bandwidths larger
than 72 kbps, this interval is less than 5 seconds.
This test verifies the ability of an implementation to use a lower
RTCP minimum interval when it is a sender in a high bandwidth
session. The test can only be run on implementations that support
this reduction, since it is optional.
The RTP implementation is configured to join the session as a sender.
The session is configured to use 360 kbps. If the recommended
algorithm for computing the reduced minimum interval is used, the
result is a 1 second interval. If the RTP implementation uses a
different algorithm, the session bandwidth should be set in such a
way to cause the reduced minimum interval to be 1 second.
Once joining the session, the RTP implementation should begin to send
both RTP and RTCP packets. The interval between RTCP packets is
measured and stored until 100 intervals have been collected.
The test is deemed successful if the smallest interval is no less
than 1/2 a second, and the largest interval is no more than 1.5
seconds. The average should be close to 1 second.
3 RTP translators
RTP translators should be tested in the same manner as end systems,
with the addition of the tests described in this section.
The architecture for testing RTP translators is shown in Figure 3.
+-----------------+
+--------+ RTP Translator +-----+
| +-----------------+ |
| |
+-------+--------+ +-------+--------+
| First RTP | | Second RTP |
| implementation | | implementation |
+----------------+ +----------------+
Figure 3: Testing architecture for translators
Perkins, et al. Informational [Page 15]
RFC 3158 RTP Testing Strategies August 2001
The first RTP implementation is instructed to send data to the
translator, which forwards the packets to the other RTP
implementation, after translating then as desired. It should be
verified that the second implementation can playout the translated
packets.
It should be verified that the packets received by the second
implementation have the same SSRC as those sent by the first
implementation. The CC should be zero and CSRC fields should not be
present in the translated packets. The other RTP header fields may
be rewritten by the translator, depending on the translation being
performed, for example
o the payload type should change if the translator changes the
encoding of the data
o the timestamp may change if, for example, the encoding,
packetisation interval or framerate is changed
o the sequence number may change if the translator merges or
splits packets
o padding may be added or removed, in particular if the
translator is adding or removing encryption
o the marker bit may be rewritten
If the translator modifies the contents of the data packets it should
be verified that the corresponding change is made to the RTCP
packets, and that the receivers can correctly process the modified
RTCP packets. In particular
o the SSRC is unchanged by the translator
o if the translator changes the data encoding it should also
change the octet count field in the SR packets
o if the translator combines multiple data packets into one it
should also change the packet count field in SR packets
o if the translator changes the sampling frequency of the data
packets it should also change the RTP timestamp field in the SR
packets
o if the translator combines multiple data packets into one it
should also change the packet loss and extended highest
sequence number fields of RR packets flowing back from the
receiver (it is legal for the translator to strip the report
Perkins, et al. Informational [Page 16]
RFC 3158 RTP Testing Strategies August 2001
blocks and send empty SR/RR packets, but this should only be
done if the transformation of the data is such that the
reception reports cannot sensibly be translated)
o the translator should forward SDES CNAME packets
o the translator may forward other SDES packets
o the translator should forward BYE packets unchanged
o the translator should forward APP packets unchanged
When the translator exits it should be verified to send a BYE packet
to each receiver containing the SSRC of the other receiver. The
receivers should be verified to correctly process this BYE packet
(this is different to the BYE test in section 2.3.3 since multiple
SSRCs may be included in each BYE if the translator also sends its
own RTCP information).
4 RTP mixers
RTP mixers should be tested in the same manner as end systems, with
the addition of the tests described in this section.
The architecture for testing RTP mixers is shown in Figure 4.
The first and second RTP implementations are instructed to send data
packets to the RTP mixer. The mixer combines those packets and sends
them to the third RTP implementation. The mixer should also process
RTCP packets from the other implementations, and should generate its
own RTCP reports.
+----------------+
| Second RTP |
| implementation |
+-------+--------+
|
| +-----------+
+-------+ RTP Mixer +-----+
| +-----------+ |
| |
+-------+--------+ +-------+--------+
| First RTP | | Third RTP |
| implementation | | implementation |
+----------------+ +----------------+
Figure 4: Testing architecture for mixers
Perkins, et al. Informational [Page 17]
RFC 3158 RTP Testing Strategies August 2001
It should be verified that the third RTP implementation can playout
the mixed packets. It should also be verified that
o the CC field in the RTP packets received by the third
implementation is set to 2
o the RTP packets received by the third implementation contain 2
CSRCs corresponding to the first and second RTP implementations
o the RTP packets received by the third implementation contain an
SSRC corresponding to that of the mixer
It should next be verified that the mixer generates SR and RR packets
for each cloud. The mixer should generate RR packets in the
direction of the first and second implementations, and SR packets in
the direction of the third implementation.
It should be verified that the SR packets sent to the third
implementation do not reference the first or second implementations,
and vice versa.
It should be verified that SDES CNAME information is forwarded across
the mixer. Other SDES fields may optionally be forwarded.
Finally, one of the implementations should be quit, and it should be
verified that the other implementations see the BYE packet. This
implementation should then be restarted and the mixer should be quit.
It should be verified that the implementations see both the mixer and
the implementations on the other side of the mixer quit (illustrating
response to BYE packets containing multiple sources).
5 SSRC collision detection
RTP has provision for the resolution of SSRC collisions. These
collisions occur when two different session participants choose the
same SSRC. In this case, both participants are supposed to send a
BYE, leave the session, and rejoin with a different SSRC, but the
same CNAME. The purpose of this test is to verify that this function
is present in the implementation.
The test is straightforward. The RTP implementation is made to join
the multicast group as a receiver. A test instrument waits for the
first RTCP packet. Once it arrives, the test instrument notes the
CNAME and SSRC from the RTCP packet. The test instrument then
generates an RTCP receiver report. This receiver report contains an
SDES chunk with an SSRC matching that of the RTP implementation, but
with a different CNAME. At this point, the implementation should
Perkins, et al. Informational [Page 18]
RFC 3158 RTP Testing Strategies August 2001
send a BYE RTCP packet (containing an SDES chunk with the old SSRC
and CNAME), and then rejoin, causing it to send a receiver report
containing an SDES chunk, but with a new SSRC and the same CNAME.
The test is deemed successful if the RTP implementation sends the
RTCP BYE and RTCP RR as described above within one minute of
receiving the colliding RR from the test instrument.
6 SSRC Randomization
According to the RTP specification, SSRC's are supposed to be chosen
randomly and uniformly over a 32 bit space. This randomization is
beneficial for several reasons:
o It reduces the probability of collisions in large groups.
o It simplifies the process of group sampling [3] which depends
on the uniform distribution of SSRC's across the 32 bit space.
Unfortunately, verifying that a random number has 32 bits of uniform
randomness requires a large number of samples. The procedure below
gives only a rough validation to the randomness used for generating
the SSRC.
The test runs as follows. The RTP implementation joins the group as
a receiver. The test instrument waits for the first RTCP packet. It
notes the SSRC in this RTCP packet. The test is repeated 2500 times,
resulting in a collection of 2500 SSRC.
The are then placed into 25 bins. An SSRC with value X is placed
into bin FLOOR(X/(2**32 / 25)). The idea is to break the 32 bit
space into 25 regions, and compute the number of SSRC in each region.
Ideally, there should be 40 SSRC in each bin. Of course, the actual
number in each bin is a random variable whose expectation is 40.
With 2500 SSRC, the coefficient of variation of the number of SSRC in
a bin is 0.1, which means the number should be between 36 and 44.
The test is thus deemed successful if each bin has no less than 30
and no more than 50 SSRC.
Running this test may require substantial amounts of time,
particularly if there is no automated way to have the implementation
join the session. In such a case, the test can be run fewer times.
With 26 tests, half of the SSRC should be less than 2**31, and the
other half higher. The coefficient of variation in this case is 0.2,
so the test is successful if there are more than 8 SSRC less than
2**31, and less than 26.
Perkins, et al. Informational [Page 19]
RFC 3158 RTP Testing Strategies August 2001
In general, if the SSRC is collected N times, and there are B bins,
the coefficient of variation of the number of SSRC in each bin is
given by:
coeff = SQRT( (B-1)/N )
7 Security Considerations
Implementations of RTP are subject to the security considerations
mentioned in the RTP specification [1] and any applicable RTP profile
(e.g., [2]). There are no additional security considerations implied
by the testing strategies described in this memo.
8 Authors' Addresses
Colin Perkins
USC Information Sciences Institute
3811 North Fairfax Drive
Suite 200
Arlington, VA 22203
EMail: csp@isi.edu
Jonathan Rosenberg
dynamicsoft
72 Eagle Rock Ave.
First Floor
East Hanover, NJ 07936
EMail: jdrosen@dynamicsoft.com
Henning Schulzrinne
Columbia University
M/S 0401
1214 Amsterdam Ave.
New York, NY 10027-7003
EMail: schulzrinne@cs.columbia.edu
Perkins, et al. Informational [Page 20]
RFC 3158 RTP Testing Strategies August 2001
9 References
[1] Schulzrinne, H., Casner, S., Frederick R. and V. Jacobson, "RTP:
A Transport Protocol to Real-Time Applications", Work in Progress
(update to RFC 1889), March 2001.
[2] Schulzrinne H. and S. Casner, "RTP Profile for Audio and Video
Conferences with Minimal Control", Work in Progress (update to
RFC 1890), March 2001.
[3] Rosenberg, J. and Schulzrinne, H. "Sampling of the Group
Membership in RTP", RFC 2762, February 2000.
Perkins, et al. Informational [Page 21]
RFC 3158 RTP Testing Strategies August 2001
Full Copyright Statement
Copyright (C) The Internet Society (2001). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Perkins, et al. Informational [Page 22]
|
