Network Working Group K. Kompella, Ed.
Request for Comments: 4761 Y. Rekhter, Ed.
Category: Standards Track Juniper Networks
January 2007
Virtual Private LAN Service (VPLS)
Using BGP for Auto-Discovery and Signaling
Status of This Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The IETF Trust (2007).
IESG Note
The L2VPN Working Group produced two separate documents, RFC 4762 and
this document, that ultimately perform similar functions in different
manners. Be aware that each method is commonly referred to as "VPLS"
even though they are distinct and incompatible with one another.
Abstract
Virtual Private LAN Service (VPLS), also known as Transparent LAN
Service and Virtual Private Switched Network service, is a useful
Service Provider offering. The service offers a Layer 2 Virtual
Private Network (VPN); however, in the case of VPLS, the customers in
the VPN are connected by a multipoint Ethernet LAN, in contrast to
the usual Layer 2 VPNs, which are point-to-point in nature.
This document describes the functions required to offer VPLS, a
mechanism for signaling a VPLS, and rules for forwarding VPLS frames
across a packet switched network.
Kompella & Rekhter Standards Track [Page 1]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
Table of Contents
1. Introduction ....................................................3
1.1. Scope of This Document .....................................3
1.2. Conventions Used in This Document ..........................4
2. Functional Model ................................................4
2.1. Terminology ................................................5
2.2. Assumptions ................................................5
2.3. Interactions ...............................................6
3. Control Plane ...................................................6
3.1. Auto-Discovery .............................................7
3.1.1. Functions ...........................................7
3.1.2. Protocol Specification ..............................7
3.2. Signaling ..................................................8
3.2.1. Label Blocks ........................................8
3.2.2. VPLS BGP NLRI .......................................9
3.2.3. PW Setup and Teardown ..............................10
3.2.4. Signaling PE Capabilities ..........................10
3.3. BGP VPLS Operation ........................................11
3.4. Multi-AS VPLS .............................................13
3.4.1. Method (a): VPLS-to-VPLS Connections at the ASBRs ..13
3.4.2. Method (b): EBGP Redistribution of VPLS
Information between ASBRs ..........................14
3.4.3. Method (c): Multi-Hop EBGP Redistribution
of VPLS Information ................................15
3.4.4. Allocation of VE IDs across Multiple ASes ..........16
3.5. Multi-homing and Path Selection ...........................16
3.6. Hierarchical BGP VPLS .....................................17
4. Data Plane .....................................................18
4.1. Encapsulation .............................................18
4.2. Forwarding ................................................18
4.2.1. MAC Address Learning ...............................18
4.2.2. Aging ..............................................19
4.2.3. Flooding ...........................................19
4.2.4. Broadcast and Multicast ............................20
4.2.5. "Split Horizon" Forwarding .........................20
4.2.6. Qualified and Unqualified Learning .................21
4.2.7. Class of Service ...................................21
5. Deployment Options .............................................21
6. Security Considerations ........................................22
7. IANA Considerations ............................................23
8. References .....................................................24
8.1. Normative References ......................................24
8.2. Informative References ....................................24
Appendix A. Contributors .........................................26
Appendix B. Acknowledgements .....................................26
Kompella & Rekhter Standards Track [Page 2]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
1. Introduction
Virtual Private LAN Service (VPLS), also known as Transparent LAN
Service and Virtual Private Switched Network service, is a useful
service offering. A Virtual Private LAN appears in (almost) all
respects as an Ethernet LAN to customers of a Service Provider.
However, in a VPLS, the customers are not all connected to a single
LAN; the customers may be spread across a metro or wide area. In
essence, a VPLS glues together several individual LANs across a
packet switched network to appear and function as a single LAN [9].
This is accomplished by incorporating MAC address learning, flooding,
and forwarding functions in the context of pseudowires that connect
these individual LANs across the packet switched network.
This document details the functions needed to offer VPLS, and then
goes on to describe a mechanism for the auto-discovery of the
endpoints of a VPLS as well as for signaling a VPLS. It also
describes how VPLS frames are transported over tunnels across a
packet switched network. The auto-discovery and signaling mechanism
uses BGP as the control plane protocol. This document also briefly
discusses deployment options, in particular, the notion of decoupling
functions across devices.
Alternative approaches include: [14], which allows one to build a
Layer 2 VPN with Ethernet as the interconnect; and [13], which allows
one to set up an Ethernet connection across a packet switched
network. Both of these, however, offer point-to-point Ethernet
services. What distinguishes VPLS from the above two is that a VPLS
offers a multipoint service. A mechanism for setting up pseudowires
for VPLS using the Label Distribution Protocol (LDP) is defined in
[10].
1.1. Scope of This Document
This document has four major parts: defining a VPLS functional model;
defining a control plane for setting up VPLS; defining the data plane
for VPLS (encapsulation and forwarding of data); and defining various
deployment options.
The functional model underlying VPLS is laid out in Section 2. This
describes the service being offered, the network components that
interact to provide the service, and at a high level their
interactions.
The control plane described in this document uses Multiprotocol BGP
[4] to establish VPLS service, i.e., for the auto-discovery of VPLS
members and for the setup and teardown of the pseudowires that
constitute a given VPLS instance. Section 3 focuses on this, and
Kompella & Rekhter Standards Track [Page 3]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
also describes how a VPLS that spans Autonomous System boundaries is
set up, as well as how multi-homing is handled. Using BGP as the
control plane for VPNs is not new (see [14], [6], and [11]): what is
described here is based on the mechanisms proposed in [6].
The forwarding plane and the actions that a participating Provider
Edge (PE) router offering the VPLS service must take is described in
Section 4.
In Section 5, the notion of 'decoupled' operation is defined, and the
interaction of decoupled and non-decoupled PEs is described.
Decoupling allows for more flexible deployment of VPLS.
1.2. Conventions Used in This Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [1].
2. Functional Model
This will be described with reference to the following figure.
-----
/ A1 \
---- ____CE1 |
/ \ -------- -------- / | |
| A2 CE2- / \ / PE1 \ /
\ / \ / \___/ | \ -----
---- ---PE2 | \
| | \ -----
| Service Provider Network | \ / \
| | CE5 A5 |
| ___ | / \ /
|----| \ / \ PE4_/ -----
|u-PE|--PE3 / \ /
|----| -------- -------
---- / | ----
/ \/ \ / \ CE = Customer Edge Device
| A3 CE3 --CE4 A4 | PE = Provider Edge Router
\ / \ / u-PE = Layer 2 Aggregation
---- ---- A<n> = Customer site n
Figure 1: Example of a VPLS
Kompella & Rekhter Standards Track [Page 4]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
2.1. Terminology
Terminology similar to that in [6] is used: a Service Provider (SP)
network with P (Provider-only) and PE (Provider Edge) routers, and
customers with CE (Customer Edge) devices. Here, however, there is
an additional concept, that of a "u-PE", a Layer 2 PE device used for
Layer 2 aggregation. The notion of u-PE is described further in
Section 5. PE and u-PE devices are "VPLS-aware", which means that
they know that a VPLS service is being offered. The term "VE" refers
to a VPLS edge device, which could be either a PE or a u-PE.
In contrast, the CE device (which may be owned and operated by either
the SP or the customer) is VPLS-unaware; as far as the CE is
concerned, it is connected to the other CEs in the VPLS via a Layer 2
switched network. This means that there should be no changes to a CE
device, either to the hardware or the software, in order to offer
VPLS.
A CE device may be connected to a PE or a u-PE via Layer 2 switches
that are VPLS-unaware. From a VPLS point of view, such Layer 2
switches are invisible, and hence will not be discussed further.
Furthermore, a u-PE may be connected to a PE via Layer 2 and Layer 3
devices; this will be discussed further in a later section.
The term "demultiplexor" refers to an identifier in a data packet
that identifies the VPLS to which the packet belongs as well as the
ingress PE. In this document, the demultiplexor is an MPLS label.
The term "VPLS" will refer to the service as well as a particular
instantiation of the service (i.e., an emulated LAN); it should be
clear from the context which usage is intended.
2.2. Assumptions
The Service Provider Network is a packet switched network. The PEs
are assumed to be (logically) fully meshed with tunnels over which
packets that belong to a service (such as VPLS) are encapsulated and
forwarded. These tunnels can be IP tunnels, such as Generic Routing
Encapsulation (GRE), or MPLS tunnels, established by Resource
Reservation Protocol - Traffic Engineering (RSVP-TE) or LDP. These
tunnels are established independently of the services offered over
them; the signaling and establishment of these tunnels are not
discussed in this document.
"Flooding" and MAC address "learning" (see Section 4) are an integral
part of VPLS. However, these activities are private to an SP device,
i.e., in the VPLS described below, no SP device requests another SP
device to flood packets or learn MAC addresses on its behalf.
Kompella & Rekhter Standards Track [Page 5]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
All the PEs participating in a VPLS are assumed to be fully meshed in
the data plane, i.e., there is a bidirectional pseudowire between
every pair of PEs participating in that VPLS, and thus every
(ingress) PE can send a VPLS packet to the egress PE(s) directly,
without the need for an intermediate PE (see Section 4.2.5.) This
requires that VPLS PEs are logically fully meshed in the control
plane so that a PE can send a message to another PE to set up the
necessary pseudowires. See Section 3.6 for a discussion on
alternatives to achieve a logical full mesh in the control plane.
2.3. Interactions
VPLS is a "LAN Service" in that CE devices that belong to a given
VPLS instance V can interact through the SP network as if they were
connected by a LAN. VPLS is "private" in that CE devices that belong
to different VPLSs cannot interact. VPLS is "virtual" in that
multiple VPLSs can be offered over a common packet switched network.
PE devices interact to "discover" all the other PEs participating in
the same VPLS, and to exchange demultiplexors. These interactions
are control-driven, not data-driven.
u-PEs interact with PEs to establish connections with remote PEs or
u-PEs in the same VPLS. This interaction is control-driven.
PE devices can participate simultaneously in both VPLS and IP VPNs
[6]. These are independent services, and the information exchanged
for each type of service is kept separate as the Network Layer
Reachability Information (NLRI) used for this exchange has different
Address Family Identifiers (AFIs) and Subsequent Address Family
Identifiers (SAFIs). Consequently, an implementation MUST maintain a
separate routing storage for each service. However, multiple
services can use the same underlying tunnels; the VPLS or VPN label
is used to demultiplex the packets belonging to different services.
3. Control Plane
There are two primary functions of the VPLS control plane: auto-
discovery, and setup and teardown of the pseudowires that constitute
the VPLS, often called signaling. Section 3.1 and Section 3.2
describe these functions. Both of these functions are accomplished
with a single BGP Update advertisement; Section 3.3 describes how
this is done by detailing BGP protocol operation for VPLS.
Section 3.4 describes the setting up of pseudowires that span
Autonomous Systems. Section 3.5 describes how multi-homing is
handled.
Kompella & Rekhter Standards Track [Page 6]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
3.1. Auto-Discovery
Discovery refers to the process of finding all the PEs that
participate in a given VPLS instance. A PE either can be configured
with the identities of all the other PEs in a given VPLS or can use
some protocol to discover the other PEs. The latter is called auto-
discovery.
The former approach is fairly configuration-intensive, especially
since it is required that the PEs participating in a given VPLS are
fully meshed (i.e., that every PE in a given VPLS establish
pseudowires to every other PE in that VPLS). Furthermore, when the
topology of a VPLS changes (i.e., a PE is added to, or removed from,
the VPLS), the VPLS configuration on all PEs in that VPLS must be
changed.
In the auto-discovery approach, each PE "discovers" which other PEs
are part of a given VPLS by means of some protocol, in this case BGP.
This allows each PE's configuration to consist only of the identity
of the VPLS instance established on this PE, not the identity of
every other PE in that VPLS instance -- that is auto-discovered.
Moreover, when the topology of a VPLS changes, only the affected PE's
configuration changes; other PEs automatically find out about the
change and adapt.
3.1.1. Functions
A PE that participates in a given VPLS instance V must be able to
tell all other PEs in VPLS V that it is also a member of V. A PE
must also have a means of declaring that it no longer participates in
a VPLS. To do both of these, the PE must have a means of identifying
a VPLS and a means by which to communicate to all other PEs.
U-PE devices also need to know what constitutes a given VPLS;
however, they don't need the same level of detail. The PE (or PEs)
to which a u-PE is connected gives the u-PE an abstraction of the
VPLS; this is described in Section 5.
3.1.2. Protocol Specification
The specific mechanism for auto-discovery described here is based on
[14] and [6]; it uses BGP extended communities [5] to identify
members of a VPLS, in particular, the Route Target community, whose
format is described in [5]. The semantics of the use of Route
Targets is described in [6]; their use in VPLS is identical.
Kompella & Rekhter Standards Track [Page 7]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
As it has been assumed that VPLSs are fully meshed, a single Route
Target RT suffices for a given VPLS V, and in effect that RT is the
identifier for VPLS V.
A PE announces (typically via I-BGP) that it belongs to VPLS V by
annotating its NLRIs for V (see next subsection) with Route Target
RT, and acts on this by accepting NLRIs from other PEs that have
Route Target RT. A PE announces that it no longer participates in V
by withdrawing all NLRIs that it had advertised with Route Target RT.
3.2. Signaling
Once discovery is done, each pair of PEs in a VPLS must be able to
establish (and tear down) pseudowires to each other, i.e., exchange
(and withdraw) demultiplexors. This process is known as signaling.
Signaling is also used to transmit certain characteristics of the
pseudowires that a PE sets up for a given VPLS.
Recall that a demultiplexor is used to distinguish among several
different streams of traffic carried over a tunnel, each stream
possibly representing a different service. In the case of VPLS, the
demultiplexor not only says to which specific VPLS a packet belongs,
but also identifies the ingress PE. The former information is used
for forwarding the packet; the latter information is used for
learning MAC addresses. The demultiplexor described here is an MPLS
label. However, note that the PE-to-PE tunnels need not be MPLS
tunnels.
Using a distinct BGP Update message to send a demultiplexor to each
remote PE would require the originating PE to send N such messages
for N remote PEs. The solution described in this document allows a
PE to send a single (common) Update message that contains
demultiplexors for all the remote PEs, instead of N individual
messages. Doing this reduces the control plane load both on the
originating PE as well as on the BGP Route Reflectors that may be
involved in distributing this Update to other PEs.
3.2.1. Label Blocks
To accomplish this, we introduce the notion of "label blocks". A
label block, defined by a label base LB and a VE block size VBS, is a
contiguous set of labels {LB, LB+1, ..., LB+VBS-1}. Here's how label
blocks work. All PEs within a given VPLS are assigned unique VE IDs
as part of their configuration. A PE X wishing to send a VPLS update
sends the same label block information to all other PEs. Each
receiving PE infers the label intended for PE X by adding its
(unique) VE ID to the label base. In this manner, each receiving PE
gets a unique demultiplexor for PE X for that VPLS.
Kompella & Rekhter Standards Track [Page 8]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
This simple notion is enhanced with the concept of a VE block offset
VBO. A label block defined by <LB, VBO, VBS> is the set {LB+VBO,
LB+VBO+1, ..., LB+VBO+VBS-1}. Thus, instead of a single large label
block to cover all VE IDs in a VPLS, one can have several label
blocks, each with a different label base. This makes label block
management easier, and also allows PE X to cater gracefully to a PE
joining a VPLS with a VE ID that is not covered by the set of label
blocks that PE X has already advertised.
When a PE starts up, or is configured with a new VPLS instance, the
BGP process may wish to wait to receive several advertisements for
that VPLS instance from other PEs to improve the efficiency of label
block allocation.
3.2.2. VPLS BGP NLRI
The VPLS BGP NLRI described below, with a new AFI and SAFI (see [4])
is used to exchange VPLS membership and demultiplexors.
A VPLS BGP NLRI has the following information elements: a VE ID, a VE
Block Offset, a VE Block Size, and a label base. The format of the
VPLS NLRI is given below. The AFI is the L2VPN AFI (25), and the
SAFI is the VPLS SAFI (65). The Length field is in octets.
+------------------------------------+
| Length (2 octets) |
+------------------------------------+
| Route Distinguisher (8 octets) |
+------------------------------------+
| VE ID (2 octets) |
+------------------------------------+
| VE Block Offset (2 octets) |
+------------------------------------+
| VE Block Size (2 octets) |
+------------------------------------+
| Label Base (3 octets) |
+------------------------------------+
Figure 2: BGP NLRI for VPLS Information
A PE participating in a VPLS must have at least one VE ID. If the PE
is the VE, it typically has one VE ID. If the PE is connected to
several u-PEs, it has a distinct VE ID for each u-PE. It may
additionally have a VE ID for itself, if it itself acts as a VE for
that VPLS. In what follows, we will call the PE announcing the VPLS
NLRI PE-a, and we will assume that PE-a owns VE ID V (either
belonging to PE-a itself or to a u-PE connected to PE-a).
Kompella & Rekhter Standards Track [Page 9]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
VE IDs are typically assigned by the network administrator. Their
scope is local to a VPLS. A given VE ID should belong to only one
PE, unless a CE is multi-homed (see Section 3.5).
A label block is a set of demultiplexor labels used to reach a given
VE ID. A VPLS BGP NLRI with VE ID V, VE Block Offset VBO, VE Block
Size VBS, and label base LB communicates to its peers the following:
label block for V: labels from LB to (LB + VBS - 1), and
remote VE set for V: from VBO to (VBO + VBS - 1).
There is a one-to-one correspondence between the remote VE set and
the label block: VE ID (VBO + n) corresponds to label (LB + n).
3.2.3. PW Setup and Teardown
Suppose PE-a is part of VPLS foo and makes an announcement with VE ID
V, VE Block Offset VBO, VE Block Size VBS, and label base LB. If
PE-b is also part of VPLS foo and has VE ID W, PE-b does the
following:
1. checks if W is part of PE-a's 'remote VE set': if VBO <= W < VBO
+ VBS, then W is part of PE-a's remote VE set. If not, PE-b
ignores this message, and skips the rest of this procedure.
2. sets up a PW to PE-a: the demultiplexor label to send traffic
from PE-b to PE-a is computed as (LB + W - VBO).
3. checks if V is part of any 'remote VE set' that PE-b announced,
i.e., PE-b checks if V belongs to some remote VE set that PE-b
announced, say with VE Block Offset VBO', VE Block Size VBS', and
label base LB'. If not, PE-b MUST make a new announcement as
described in Section 3.3.
4. sets up a PW from PE-a: the demultiplexor label over which PE-b
should expect traffic from PE-a is computed as: (LB' + V - VBO').
If Y withdraws an NLRI for V that X was using, then X MUST tear down
its ends of the pseudowire between X and Y.
3.2.4. Signaling PE Capabilities
The following extended attribute, the "Layer2 Info Extended
Community", is used to signal control information about the
pseudowires to be setup for a given VPLS. The extended community
value is to be allocated by IANA (currently used value is 0x800A).
This information includes the Encaps Type (type of encapsulation on
Kompella & Rekhter Standards Track [Page 10]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
the pseudowires), Control Flags (control information regarding the
pseudowires), and the Maximum Transmission Unit (MTU) to be used on
the pseudowires.
The Encaps Type for VPLS is 19.
+------------------------------------+
| Extended community type (2 octets) |
+------------------------------------+
| Encaps Type (1 octet) |
+------------------------------------+
| Control Flags (1 octet) |
+------------------------------------+
| Layer-2 MTU (2 octet) |
+------------------------------------+
| Reserved (2 octets) |
+------------------------------------+
Figure 3: Layer2 Info Extended Community
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
| MBZ |C|S| (MBZ = MUST Be Zero)
+-+-+-+-+-+-+-+-+
Figure 4: Control Flags Bit Vector
With reference to Figure 4, the following bits in the Control Flags
are defined; the remaining bits, designated MBZ, MUST be set to zero
when sending and MUST be ignored when receiving this community.
Name Meaning
C A Control word [7] MUST or MUST NOT be present when
sending VPLS packets to this PE, depending on whether C
is 1 or 0, respectively
S Sequenced delivery of frames MUST or MUST NOT be used
when sending VPLS packets to this PE, depending on
whether S is 1 or 0, respectively
3.3. BGP VPLS Operation
To create a new VPLS, say VPLS foo, a network administrator must pick
an RT for VPLS foo, say RT-foo. This will be used by all PEs that
serve VPLS foo. To configure a given PE, say PE-a, to be part of
VPLS foo, the network administrator only has to choose a VE ID V for
Kompella & Rekhter Standards Track [Page 11]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
PE-a. (If PE-a is connected to u-PEs, PE-a may be configured with
more than one VE ID; in that case, the following is done for each VE
ID). The PE may also be configured with a Route Distinguisher (RD);
if not, it generates a unique RD for VPLS foo. Say the RD is
RD-foo-a. PE-a then generates an initial label block and a remote VE
set for V, defined by VE Block Offset VBO, VE Block Size VBS, and
label base LB. These may be empty.
PE-a then creates a VPLS BGP NLRI with RD RD-foo-a, VE ID V, VE Block
Offset VBO, VE Block Size VBS and label base LB. To this, it
attaches a Layer2 Info Extended Community and an RT, RT-foo. It sets
the BGP Next Hop for this NLRI as itself, and announces this NLRI to
its peers. The Network Layer protocol associated with the Network
Address of the Next Hop for the combination <AFI=L2VPN AFI, SAFI=VPLS
SAFI> is IP; this association is required by [4], Section 5. If the
value of the Length of the Next Hop field is 4, then the Next Hop
contains an IPv4 address. If this value is 16, then the Next Hop
contains an IPv6 address.
If PE-a hears from another PE, say PE-b, a VPLS BGP announcement with
RT-foo and VE ID W, then PE-a knows that PE-b is a member of the same
VPLS (auto-discovery). PE-a then has to set up its part of a VPLS
pseudowire between PE-a and PE-b, using the mechanisms in
Section 3.2. Similarly, PE-b will have discovered that PE-a is in
the same VPLS, and PE-b must set up its part of the VPLS pseudowire.
Thus, signaling and pseudowire setup is also achieved with the same
Update message.
If W is not in any remote VE set that PE-a announced for VE ID V in
VPLS foo, PE-b will not be able to set up its part of the pseudowire
to PE-a. To address this, PE-a can choose to withdraw the old
announcement(s) it made for VPLS foo, and announce a new Update with
a larger remote VE set and corresponding label block that covers all
VE IDs that are in VPLS foo. This, however, may cause some service
disruption. An alternative for PE-a is to create a new remote VE set
and corresponding label block, and announce them in a new Update,
without withdrawing previous announcements.
If PE-a's configuration is changed to remove VE ID V from VPLS foo,
then PE-a MUST withdraw all its announcements for VPLS foo that
contain VE ID V. If all of PE-a's links to its CEs in VPLS foo go
down, then PE-a SHOULD either withdraw all its NLRIs for VPLS foo or
let other PEs in the VPLS foo know in some way that PE-a is no longer
connected to its CEs.
Kompella & Rekhter Standards Track [Page 12]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
3.4. Multi-AS VPLS
As in [14] and [6], the above auto-discovery and signaling functions
are typically announced via I-BGP. This assumes that all the sites
in a VPLS are connected to PEs in a single Autonomous System (AS).
However, sites in a VPLS may connect to PEs in different ASes. This
leads to two issues: 1) there would not be an I-BGP connection
between those PEs, so some means of signaling across ASes is needed;
and 2) there may not be PE-to-PE tunnels between the ASes.
A similar problem is solved in [6], Section 10. Three methods are
suggested to address issue (1); all these methods have analogs in
multi-AS VPLS.
Here is a diagram for reference:
__________ ____________ ____________ __________
/ \ / \ / \ / \
\___/ AS 1 \ / AS 2 \___/
\ /
+-----+ +-------+ | +-------+ +-----+
| PE1 | ---...--- | ASBR1 | ======= | ASBR2 | ---...--- | PE2 |
+-----+ +-------+ | +-------+ +-----+
___ / \ ___
/ \ / \ / \
\__________/ \____________/ \____________/ \__________/
Figure 5: Inter-AS VPLS
As in the above reference, three methods for signaling inter-provider
VPLS are given; these are presented in order of increasing
scalability. Method (a) is the easiest to understand conceptually,
and the easiest to deploy; however, it requires an Ethernet
interconnect between the ASes, and both VPLS control and data plane
state on the AS border routers (ASBRs). Method (b) requires VPLS
control plane state on the ASBRs and MPLS on the AS-AS interconnect
(which need not be Ethernet). Method (c) requires MPLS on the AS-AS
interconnect, but no VPLS state of any kind on the ASBRs.
3.4.1. Method (a): VPLS-to-VPLS Connections at the ASBRs
In this method, an AS Border Router (ASBR1) acts as a PE for all
VPLSs that span AS1 and an AS to which ASBR1 is connected, such as
AS2 here. The ASBR on the neighboring AS (ASBR2) is viewed by ASBR1
as a CE for the VPLSs that span AS1 and AS2; similarly, ASBR2 acts as
a PE for this VPLS from AS2's point of view, and views ASBR1 as a CE.
Kompella & Rekhter Standards Track [Page 13]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
This method does not require MPLS on the ASBR1-ASBR2 link, but does
require that this link carry Ethernet traffic and that there be a
separate VLAN sub-interface for each VPLS traversing this link. It
further requires that ASBR1 does the PE operations (discovery,
signaling, MAC address learning, flooding, encapsulation, etc.) for
all VPLSs that traverse ASBR1. This imposes a significant burden on
ASBR1, both on the control plane and the data plane, which limits the
number of multi-AS VPLSs.
Note that in general, there will be multiple connections between a
pair of ASes, for redundancy. In this case, the Spanning Tree
Protocol (STP) [15], or some other means of loop detection and
prevention, must be run on each VPLS that spans these ASes, so that a
loop-free topology can be constructed in each VPLS. This imposes a
further burden on the ASBRs and PEs participating in those VPLSs, as
these devices would need to run a loop detection algorithm for each
such VPLS. How this may be achieved is outside the scope of this
document.
3.4.2. Method (b): EBGP Redistribution of VPLS Information between
ASBRs
This method requires I-BGP peerings between the PEs in AS1 and ASBR1
in AS1 (perhaps via route reflectors), an E-BGP peering between ASBR1
and ASBR2 in AS2, and I-BGP peerings between ASBR2 and the PEs in
AS2. In the above example, PE1 sends a VPLS NLRI to ASBR1 with a
label block and itself as the BGP nexthop; ASBR1 sends the NLRI to
ASBR2 with new labels and itself as the BGP nexthop; and ASBR2 sends
the NLRI to PE2 with new labels and itself as the nexthop.
Correspondingly, there are three tunnels: T1 from PE1 to ASBR1, T2
from ASBR1 to ASBR2, and T3 from ASBR2 to PE2. Within each tunnel,
the VPLS label to be used is determined by the receiving device;
e.g., the VPLS label within T1 is a label from the label block that
ASBR1 sent to PE1. The ASBRs are responsible for receiving VPLS
packets encapsulated in a tunnel and performing the appropriate label
swap operations described next so that the next receiving device can
correctly identify and forward the packet.
The VPLS NLRI that ASBR1 sends to ASBR2 (and the NLRI that ASBR2
sends to PE2) is identical to the VPLS NLRI that PE1 sends to ASBR1,
except for the label block. To be precise, the Length, the Route
Distinguisher, the VE ID, the VE Block Offset, and the VE Block Size
MUST be the same; the Label Base may be different. Furthermore,
ASBR1 must also update its forwarding path as follows: if the Label
Base sent by PE1 is L1, the Label-block Size is N, the Label Base
sent by ASBR1 is L2, and the tunnel label from ASBR1 to PE1 is T,
then ASBR1 must install the following in the forwarding path:
Kompella & Rekhter Standards Track [Page 14]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
swap L2 with L1 and push T,
swap L2+1 with L1+1 and push T, ...
swap L2+N-1 with L1+N-1 and push T.
ASBR2 must act similarly, except that it may not need a tunnel label
if it is directly connected with ASBR1.
When PE2 wants to send a VPLS packet to PE1, PE2 uses its VE ID to
get the right VPLS label from ASBR2's label block for PE1, and uses a
tunnel label to reach ASBR2. ASBR2 swaps the VPLS label with the
label from ASBR1; ASBR1 then swaps the VPLS label with the label from
PE1, and pushes a tunnel label to reach PE1.
In this method, one needs MPLS on the ASBR1-ASBR2 interface, but
there is no requirement that the link layer be Ethernet.
Furthermore, the ASBRs take part in distributing VPLS information.
However, the data plane requirements of the ASBRs are much simpler
than in method (a), being limited to label operations. Finally, the
construction of loop-free VPLS topologies is done by routing
decisions, viz. BGP path and nexthop selection, so there is no need
to run the Spanning Tree Protocol on a per-VPLS basis. Thus, this
method is considerably more scalable than method (a).
3.4.3. Method (c): Multi-Hop EBGP Redistribution of VPLS Information
between ASes
In this method, there is a multi-hop E-BGP peering between the PEs
(or preferably, a Route Reflector) in AS1 and the PEs (or Route
Reflector) in AS2. PE1 sends a VPLS NLRI with labels and nexthop
self to PE2; if this is via route reflectors, the BGP nexthop is not
changed. This requires that there be a tunnel LSP from PE1 to PE2.
This tunnel LSP can be created exactly as in [6], Section 10 (c), for
example using E-BGP to exchange labeled IPv4 routes for the PE
loopbacks.
When PE1 wants to send a VPLS packet to PE2, it pushes the VPLS label
corresponding to its own VE ID onto the packet. It then pushes the
tunnel label(s) to reach PE2.
This method requires no VPLS information (in either the control or
the data plane) on the ASBRs. The ASBRs only need to set up PE-to-PE
tunnel LSPs in the control plane, and do label operations in the data
plane. Again, as in the case of method (b), the construction of
loop-free VPLS topologies is done by routing decisions, i.e., BGP
Kompella & Rekhter Standards Track [Page 15]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
path and nexthop selection, so there is no need to run the Spanning
Tree Protocol on a per-VPLS basis. This option is likely to be the
most scalable of the three methods presented here.
3.4.4. Allocation of VE IDs across Multiple ASes
In order to ease the allocation of VE IDs for a VPLS that spans
multiple ASes, one can allocate ranges for each AS. For example, AS1
uses VE IDs in the range 1 to 100, AS2 from 101 to 200, etc. If
there are 10 sites attached to AS1 and 20 to AS2, the allocated VE
IDs could be 1-10 and 101 to 120. This minimizes the number of VPLS
NLRIs that are exchanged while ensuring that VE IDs are kept unique.
In the above example, if AS1 needed more than 100 sites, then another
range can be allocated to AS1. The only caveat is that there be no
overlap between VE ID ranges among ASes. The exception to this rule
is multi-homing, which is dealt with below.
3.5. Multi-homing and Path Selection
It is often desired to multi-home a VPLS site, i.e., to connect it to
multiple PEs, perhaps even in different ASes. In such a case, the
PEs connected to the same site can be configured either with the same
VE ID or with different VE IDs. In the latter case, it is mandatory
to run STP on the CE device, and possibly on the PEs, to construct a
loop-free VPLS topology. How this can be accomplished is outside the
scope of this document; however, the rest of this section will
describe in some detail the former case. Note that multi-homing by
the SP and STP on the CEs can co-exist; thus, it is recommended that
the VPLS customer run STP if the CEs are able to.
In the case where the PEs connected to the same site are assigned the
same VE ID, a loop-free topology is constructed by routing
mechanisms, in particular, by BGP path selection. When a BGP speaker
receives two equivalent NLRIs (see below for the definition), it
applies standard path selection criteria such as Local Preference and
AS Path Length to determine which NLRI to choose; it MUST pick only
one. If the chosen NLRI is subsequently withdrawn, the BGP speaker
applies path selection to the remaining equivalent VPLS NLRIs to pick
another; if none remain, the forwarding information associated with
that NLRI is removed.
Two VPLS NLRIs are considered equivalent from a path selection point
of view if the Route Distinguisher, the VE ID, and the VE Block
Offset are the same. If two PEs are assigned the same VE ID in a
given VPLS, they MUST use the same Route Distinguisher, and they
SHOULD announce the same VE Block Size for a given VE Offset.
Kompella & Rekhter Standards Track [Page 16]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
3.6. Hierarchical BGP VPLS
This section discusses how one can scale the VPLS control plane when
using BGP. There are at least three aspects of scaling the control
plane:
1. alleviating the full mesh connectivity requirement among VPLS BGP
speakers;
2. limiting BGP VPLS message passing to just the interested speakers
rather than all BGP speakers; and
3. simplifying the addition and deletion of BGP speakers, whether
for VPLS or other applications.
Fortunately, the use of BGP for Internet routing as well as for IP
VPNs has yielded several good solutions for all these problems. The
basic technique is hierarchy, using BGP Route Reflectors (RRs) [8].
The idea is to designate a small set of Route Reflectors that are
themselves fully meshed, and then establish a BGP session between
each BGP speaker and one or more RRs. In this way, there is no need
for direct full mesh connectivity among all the BGP speakers. If the
particular scaling needs of a provider require a large number of RRs,
then this technique can be applied recursively: the full mesh
connectivity among the RRs can be brokered by yet another level of
RRs. The use of RRs solves problems 1 and 3 above.
It is important to note that RRs, as used for VPLS and VPNs, are
purely a control plane technique. The use of RRs introduces no data
plane state and no data plane forwarding requirements on the RRs, and
does not in any way change the forwarding path of VPLS traffic. This
is in contrast to the technique of Hierarchical VPLS defined in [10].
Another consequence of this approach is that it is not required that
one set of RRs handles all BGP messages, or that a particular RR
handle all messages from a given PE. One can define several sets of
RRs, for example, a set to handle VPLS, another to handle IP VPNs,
and another for Internet routing. Another partitioning could be to
have some subset of VPLSs and IP VPNs handled by one set of RRs, and
another subset of VPLSs and IP VPNs handled by another set of RRs;
the use of Route Target Filtering (RTF), described in [12], can make
this simpler and more effective.
Finally, problem 2 (that of limiting BGP VPLS message passing to just
the interested BGP speakers) is addressed by the use of RTF. This
technique is orthogonal to the use of RRs, but works well in
conjunction with RRs. RTF is also very effective in inter-AS VPLS;
more details on how RTF works and its benefits are provided in [12].
Kompella & Rekhter Standards Track [Page 17]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
It is worth mentioning an aspect of the control plane that is often a
source of confusion. No MAC addresses are exchanged via BGP. All
MAC address learning and aging is done in the data plane individually
by each PE. The only task of BGP VPLS message exchange is auto-
discovery and label exchange.
Thus, BGP processing for VPLS occurs when
1. a PE joins or leaves a VPLS; or
2. a failure occurs in the network, bringing down a PE-PE tunnel or
a PE-CE link.
These events are relatively rare, and typically, each such event
causes one BGP update to be generated. Coupled with BGP's messaging
efficiency when used for signaling VPLS, these observations lead to
the conclusion that BGP as a control plane for VPLS will scale quite
well in terms of both processing and memory requirements.
4. Data Plane
This section discusses two aspects of the data plane for PEs and
u-PEs implementing VPLS: encapsulation and forwarding.
4.1. Encapsulation
Ethernet frames received from CE devices are encapsulated for
transmission over the packet switched network connecting the PEs.
The encapsulation is as in [7].
4.2. Forwarding
VPLS packets are classified as belonging to a given service instance
and associated forwarding table based on the interface over which the
packet is received. Packets are forwarded in the context of the
service instance based on the destination MAC address. The former
mapping is determined by configuration. The latter is the focus of
this section.
4.2.1. MAC Address Learning
As was mentioned earlier, the key distinguishing feature of VPLS is
that it is a multipoint service. This means that the entire Service
Provider network should appear as a single logical learning bridge
for each VPLS that the SP network supports. The logical ports for
the SP "bridge" are the customer ports as well as the pseudowires on
a VE. Just as a learning bridge learns MAC addresses on its ports,
the SP bridge must learn MAC addresses at its VEs.
Kompella & Rekhter Standards Track [Page 18]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
Learning consists of associating source MAC addresses of packets with
the (logical) ports on which they arrive; this association is the
Forwarding Information Base (FIB). The FIB is used for forwarding
packets. For example, suppose the bridge receives a packet with
source MAC address S on (logical) port P. If subsequently, the
bridge receives a packet with destination MAC address S, it knows
that it should send the packet out on port P.
If a VE learns a source MAC address S on logical port P, then later
sees S on a different port P', then the VE MUST update its FIB to
reflect the new port P'. A VE MAY implement a mechanism to damp
flapping of source ports for a given MAC address.
4.2.2. Aging
VPLS PEs SHOULD have an aging mechanism to remove a MAC address
associated with a logical port, much the same as learning bridges do.
This is required so that a MAC address can be relearned if it "moves"
from a logical port to another logical port, either because the
station to which that MAC address belongs really has moved or because
of a topology change in the LAN that causes this MAC address to
arrive on a new port. In addition, aging reduces the size of a VPLS
MAC table to just the active MAC addresses, rather than all MAC
addresses in that VPLS.
The "age" of a source MAC address S on a logical port P is the time
since it was last seen as a source MAC on port P. If the age exceeds
the aging time T, S MUST be flushed from the FIB. This of course
means that every time S is seen as a source MAC address on port P,
S's age is reset.
An implementation SHOULD provide a configurable knob to set the aging
time T on a per-VPLS basis. In addition, an implementation MAY
accelerate aging of all MAC addresses in a VPLS if it detects certain
situations, such as a Spanning Tree topology change in that VPLS.
4.2.3. Flooding
When a bridge receives a packet to a destination that is not in its
FIB, it floods the packet on all the other ports. Similarly, a VE
will flood packets to an unknown destination to all other VEs in the
VPLS.
In Figure 1 above, if CE2 sent an Ethernet frame to PE2, and the
destination MAC address on the frame was not in PE2's FIB (for that
VPLS), then PE2 would be responsible for flooding that frame to every
Kompella & Rekhter Standards Track [Page 19]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
other PE in the same VPLS. On receiving that frame, PE1 would be
responsible for further flooding the frame to CE1 and CE5 (unless PE1
knew which CE "owned" that MAC address).
On the other hand, if PE3 received the frame, it could delegate
further flooding of the frame to its u-PE. If PE3 was connected to
two u-PEs, it would announce that it has two u-PEs. PE3 could either
announce that it is incapable of flooding, in which case it would
receive two frames, one for each u-PE, or it could announce that it
is capable of flooding, in which case it would receive one copy of
the frame, which it would then send to both u-PEs.
4.2.4. Broadcast and Multicast
There is a well-known broadcast MAC address. An Ethernet frame whose
destination MAC address is the broadcast MAC address must be sent to
all stations in that VPLS. This can be accomplished by the same
means that is used for flooding.
There is also an easily recognized set of "multicast" MAC addresses.
Ethernet frames with a destination multicast MAC address MAY be
broadcast to all stations; a VE MAY also use certain techniques to
restrict transmission of multicast frames to a smaller set of
receivers, those that have indicated interest in the corresponding
multicast group. Discussion of this is outside the scope of this
document.
4.2.5. "Split Horizon" Forwarding
When a PE capable of flooding (say PEx) receives a broadcast Ethernet
frame, or one with an unknown destination MAC address, it must flood
the frame. If the frame arrived from an attached CE, PEx must send a
copy of the frame to every other attached CE, as well as to all other
PEs participating in the VPLS. If, on the other hand, the frame
arrived from another PE (say PEy), PEx must send a copy of the packet
only to attached CEs. PEx MUST NOT send the frame to other PEs,
since PEy would have already done so. This notion has been termed
"split horizon" forwarding and is a consequence of the PEs being
logically fully meshed for VPLS.
Split horizon forwarding rules apply to broadcast and multicast
packets, as well as packets to an unknown MAC address.
Kompella & Rekhter Standards Track [Page 20]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
4.2.6. Qualified and Unqualified Learning
The key for normal Ethernet MAC learning is usually just the
(6-octet) MAC address. This is called "unqualified learning".
However, it is also possible that the key for learning includes the
VLAN tag when present; this is called "qualified learning".
In the case of VPLS, learning is done in the context of a VPLS
instance, which typically corresponds to a customer. If the customer
uses VLAN tags, one can make the same distinctions of qualified and
unqualified learning. If the key for learning within a VPLS is just
the MAC address, then this VPLS is operating under unqualified
learning. If the key for learning is (customer VLAN tag + MAC
address), then this VPLS is operating under qualified learning.
Choosing between qualified and unqualified learning involves several
factors, the most important of which is whether one wants a single
global broadcast domain (unqualified) or a broadcast domain per VLAN
(qualified). The latter makes flooding and broadcasting more
efficient, but requires larger MAC tables. These considerations
apply equally to normal Ethernet forwarding and to VPLS.
4.2.7. Class of Service
In order to offer different Classes of Service within a VPLS, an
implementation MAY choose to map 802.1p bits in a customer Ethernet
frame with a VLAN tag to an appropriate setting of EXP bits in the
pseudowire and/or tunnel label, allowing for differential treatment
of VPLS frames in the packet switched network.
To be useful, an implementation SHOULD allow this mapping function to
be different for each VPLS, as each VPLS customer may have its own
view of the required behavior for a given setting of 802.1p bits.
5. Deployment Options
In deploying a network that supports VPLS, the SP must decide what
functions the VPLS-aware device closest to the customer (the VE)
supports. The default case described in this document is that the VE
is a PE. However, there are a number of reasons that the VE might be
a device that does all the Layer 2 functions (such as MAC address
learning and flooding), and a limited set of Layer 3 functions (such
as communicating to its PE), but, for example, doesn't do full-
fledged discovery and PE-to-PE signaling. Such a device is called a
"u-PE".
Kompella & Rekhter Standards Track [Page 21]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
As both of these cases have benefits, one would like to be able to
"mix and match" these scenarios. The signaling mechanism presented
here allows this. For example, in a given provider network, one PE
may be directly connected to CE devices, another may be connected to
u-PEs that are connected to CEs, and a third may be connected
directly to a customer over some interfaces and to u-PEs over others.
All these PEs perform discovery and signaling in the same manner.
How they do learning and forwarding depends on whether or not there
is a u-PE; however, this is a local matter, and is not signaled.
However, the details of the operation of a u-PE and its interactions
with PEs and other u-PEs are beyond the scope of this document.
6. Security Considerations
The focus in Virtual Private LAN Service is the privacy of data,
i.e., that data in a VPLS is only distributed to other nodes in that
VPLS and not to any external agent or other VPLS. Note that VPLS
does not offer confidentiality, integrity, or authentication: VPLS
packets are sent in the clear in the packet switched network, and a
man-in-the-middle can eavesdrop, and may be able to inject packets
into the data stream. If security is desired, the PE-to-PE tunnels
can be IPsec tunnels. For more security, the end systems in the VPLS
sites can use appropriate means of encryption to secure their data
even before it enters the Service Provider network.
There are two aspects to achieving data privacy in a VPLS: securing
the control plane and protecting the forwarding path. Compromise of
the control plane could result in a PE sending data belonging to some
VPLS to another VPLS, or blackholing VPLS data, or even sending it to
an eavesdropper; none of which are acceptable from a data privacy
point of view. Since all control plane exchanges are via BGP,
techniques such as in [2] help authenticate BGP messages, making it
harder to spoof updates (which can be used to divert VPLS traffic to
the wrong VPLS) or withdraws (denial-of-service attacks). In the
multi-AS methods (b) and (c) described in Section 3, this also means
protecting the inter-AS BGP sessions, between the ASBRs, the PEs, or
the Route Reflectors. One can also use the techniques described in
Section 10 (b) and (c) of [6], both for the control plane and the
data plane. Note that [2] will not help in keeping VPLS labels
private -- knowing the labels, one can eavesdrop on VPLS traffic.
However, this requires access to the data path within a Service
Provider network.
There can also be misconfiguration leading to unintentional
connection of CEs in different VPLSs. This can be caused, for
example, by associating the wrong Route Target with a VPLS instance.
This problem, shared by [6], is for further study.
Kompella & Rekhter Standards Track [Page 22]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
Protecting the data plane requires ensuring that PE-to-PE tunnels are
well-behaved (this is outside the scope of this document), and that
VPLS labels are accepted only from valid interfaces. For a PE, valid
interfaces comprise links from P routers. For an ASBR, a valid
interface is a link from an ASBR in an AS that is part of a given
VPLS. It is especially important in the case of multi-AS VPLSs that
one accept VPLS packets only from valid interfaces.
MPLS-in-IP and MPLS-in-GRE tunneling are specified in [3]. If it is
desired to use such tunnels to carry VPLS packets, then the security
considerations described in Section 8 of that document must be fully
understood. Any implementation of VPLS that allows VPLS packets to
be tunneled as described in that document MUST contain an
implementation of IPsec that can be used as therein described. If
the tunnel is not secured by IPsec, then the technique of IP address
filtering at the border routers, described in Section 8.2 of that
document, is the only means of ensuring that a packet that exits the
tunnel at a particular egress PE was actually placed in the tunnel by
the proper tunnel head node (i.e., that the packet does not have a
spoofed source address). Since border routers frequently filter only
source addresses, packet filtering may not be effective unless the
egress PE can check the IP source address of any tunneled packet it
receives, and compare it to a list of IP addresses that are valid
tunnel head addresses. Any implementation that allows MPLS-in-IP
and/or MPLS-in-GRE tunneling to be used without IPsec MUST allow the
egress PE to validate in this manner the IP source address of any
tunneled packet that it receives.
7. IANA Considerations
IANA allocated value (25) for AFI for L2VPN information. This should
be the same as the AFI requested by [11].
IANA allocated an extended community value (0x800a) for the Layer2
Info Extended Community.
Kompella & Rekhter Standards Track [Page 23]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
8. References
8.1. Normative References
[1] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
[2] Heffernan, A., "Protection of BGP Sessions via the TCP MD5
Signature Option", RFC 2385, August 1998.
[3] Worster, T., Rekhter, Y., and E. Rosen, "Encapsulating MPLS in
IP or Generic Routing Encapsulation (GRE)", RFC 4023,
March 2005.
[4] Bates, T., Katz, D., and Y. Rekhter, "Multiprotocol Extensions
for BGP-4", RFC 4760, January 2007.
[5] Sangli, S., Tappan, D., and Y. Rekhter, "BGP Extended
Communities Attribute", RFC 4360, February 2006.
[6] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private Networks
(VPNs)", RFC 4364, February 2006.
[7] Martini, L., Rosen, E., El-Aawar, N., and G. Heron,
"Encapsulation Methods for Transport of Ethernet over MPLS
Networks", RFC 4448, April 2006.
8.2. Informative References
[8] Bates, T., Chen, E., and R. Chandra, "BGP Route Reflection: An
Alternative to Full Mesh Internal BGP (IBGP)", RFC 4456,
April 2006.
[9] Andersson, L. and E. Rosen, "Framework for Layer 2 Virtual
Private Networks (L2VPNs)", RFC 4664, September 2006.
[10] Lasserre, M., Ed. and V. Kompella, Ed., "Virtual Private LAN
Service (VPLS) Using Label Distribution Protocol (LDP)
Signaling", RFC 4762, January 2007.
[11] Ould-Brahim, H., "Using BGP as an Auto-Discovery Mechanism for
VR-based Layer-3 VPNs", Work in Progress, April 2006.
[12] Marques, P., "Constrained VPN Route Distribution", Work in
Progress, June 2005.
Kompella & Rekhter Standards Track [Page 24]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
[13] Martini, L., Rosen, E., El-Aawar, N., Smith, T., and G. Heron,
"Pseudowire Setup and Maintenance Using the Label Distribution
Protocol (LDP)", RFC 4447, April 2006.
[14] Kompella, K., "Layer 2 VPNs Over Tunnels", Work in Progress,
January 2006.
[15] Institute of Electrical and Electronics Engineers, "Information
technology - Telecommunications and information exchange
between systems - Local and metropolitan area networks - Common
specifications - Part 3: Media Access Control (MAC) Bridges:
Revision. This is a revision of ISO/IEC 10038: 1993, 802.1j-
1992 and 802.6k-1992. It incorporates P802.11c, P802.1p and
P802.12e. ISO/IEC 15802-3: 1998.", IEEE Standard 802.1D,
July 1998.
Kompella & Rekhter Standards Track [Page 25]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
Appendix A. Contributors
The following contributed to this document:
Javier Achirica, Telefonica
Loa Andersson, Acreo
Giles Heron, Tellabs
Sunil Khandekar, Alcatel-Lucent
Chaitanya Kodeboyina, Nuova Systems
Vach Kompella, Alcatel-Lucent
Marc Lasserre, Alcatel-Lucent
Pierre Lin
Pascal Menezes
Ashwin Moranganti, Appian
Hamid Ould-Brahim, Nortel
Seo Yeong-il, Korea Tel
Appendix B. Acknowledgements
Thanks to Joe Regan and Alfred Nothaft for their contributions. Many
thanks too to Eric Ji, Chaitanya Kodeboyina, Mike Loomis, and Elwyn
Davies for their detailed reviews.
Kompella & Rekhter Standards Track [Page 26]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
Editors' Addresses
Kireeti Kompella
Juniper Networks
1194 N. Mathilda Ave.
Sunnyvale, CA 94089
US
EMail: kireeti@juniper.net
Yakov Rekhter
Juniper Networks
1194 N. Mathilda Ave.
Sunnyvale, CA 94089
US
EMail: yakov@juniper.net
Kompella & Rekhter Standards Track [Page 27]
RFC 4761 BGP Auto-Discovery and Signaling for VPLS January 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Kompella & Rekhter Standards Track [Page 28]
|
